Electrical Learning Lab
Free interactive lessons on the fundamentals and the equipment behind electrical work. Change the values, flip the switches, take the gear apart and watch what happens. No sign-up needed.
Lessons
- Ohm's Law: Voltage, Current and Resistance. Change the voltage and resistance on a working circuit and watch the current respond. Then use V = I × R the way it gets used in the field. Lesson, beginner, about 12 minutes.
- Series and Parallel Circuits. Wire the same three lamps two ways, then burn one out, short one and overload the breaker. See why buildings are wired in parallel. Lesson, beginner, about 15 minutes.
- How Three-Way Switches Work. Flip two switches and watch one light. Follow the travelers, switch between a schematic and a hallway view, and track down a wiring mistake. Lesson, beginner, about 14 minutes.
- Motor Starters and Overload Protection. Take a starter apart, press START on a three-wire control circuit, overload the motor until the relay trips and learn which device clears a short circuit. Lesson, intermediate, about 18 minutes.
- Transformers and Voltage. Wind the primary and secondary, pick a supply and a load, and watch voltage, current and power follow the turns ratio. Then read a kVA nameplate like a pro. Lesson, intermediate, about 16 minutes.
- Three-Phase Power: Waveforms, Wye and Delta. Watch three voltages 120 degrees apart turn as waves and phasors, derive the square root of three, and size the line current for a balanced load on wye and delta systems. Lesson, intermediate, about 16 minutes.
- Electrical Panels and Circuit Protection. Take a 120/240 V panelboard apart, switch and load its circuits, watch the buses and neutral share the current and learn why an overload and a fault trip a breaker differently. Lesson, beginner, about 17 minutes.
- Data Center Electrical Infrastructure. Walk the power chain from utility to rack, drop the utility and watch the UPS, generator and transfer switch respond, then compare N, N+1 and 2N designs. Lesson, intermediate, about 18 minutes.
- The 120/240 V Service: A Split-Phase Laboratory. Measure a simulated 120/240 V service probe by probe, balance and unbalance the two legs, watch what the neutral carries and see what an open neutral does to the loads. Virtual lab, beginner, about 16 minutes.
- Grounding, Bonding and Subpanels: Inside the Panel. Take a service panel and a subpanel apart, fault an appliance case and follow the current home, measure touch voltage, and learn why neutrals and grounds separate at a subpanel. Equipment explorer, intermediate, about 18 minutes.
- GFCI, AFCI, Overload and Short Circuit: Which Device Responds. Open a GFCI receptacle and an AFCI breaker, then run a shock, a leak, an overload, a short circuit and arcing through one circuit and see which device opens, on which element, and how fast. Virtual lab, intermediate, about 18 minutes.
- Voltage Drop and Wire Size: Calculator and Lab. Open a cable, see what circular mils are, then size real runs with a calculator that shows the drop in volts, percent and watts of heat, and a meter you can put across any two points. Calculator, intermediate, about 16 minutes.
- The Electrical Panel in Three Dimensions. Turn a Square D QO load center in three dimensions, explode it, build it in installation order, and watch the engines' current and trips on the real parts. Equipment explorer, beginner, about 15 minutes.
- Conduit Bending: The 90° Stub-Up in EMT. Measure, mark, line up a hand bender and bend a 90° stub-up in 1/2, 3/4 or 1 in EMT, in a 3D workshop with guided, practice and challenge modes that grade the finished stub. Virtual lab, beginner, about 22 minutes.
- Conduit Bending: Two-Bend Offsets in EMT. Work out an offset's center to center distance and shrink from the makers' table, mark A and B, bend the first on the floor and the second in the air, and grade the piece on a curb in 1/2, 3/4 or 1 in EMT. Virtual lab, intermediate, about 25 minutes.
- Explore the Electrical System of a House. A 3D training house with six branch circuits, a virtual meter, a hidden fault to diagnose and a repair to make safely, a conduit offset to bend for the garage and a living room to lay out with outlets. Troubleshooting workshop, intermediate, about 45 minutes.
- EV Load Calc Lab: Can This Panel Take a Charger?. A 3D house with its range, dryer, water heater, outdoor unit and an electric car: walk the existing-house load calculation step by step, compare real home chargers and size the charger's circuit. Virtual lab, intermediate, about 35 minutes.
How the lab works
Each lesson pairs a plain explanation with a working model you can change, from a single circuit to a motor starter, a transformer or a panel. Move the voltage or flip a switch and the readings respond the way the math says they should.
The lab is written for apprentices getting ready for class and for electricians brushing up on theory. Worked examples show every step, and each lesson ends with a short quiz that explains its answers.
Progress is kept on your own phone or computer. There is no account to make and nothing to install.
- Change real values. Move the voltage, resistance and switches, and the readings follow the same math electricians use.
- Tap any part. Every drawing has a parts list. Tap a part to see what it does and where you meet it in the field.
- Take the challenges. Short hands-on problems check your answer the moment you make it, with the working shown.
- Check yourself. Each lesson ends with a five-question quiz. Wrong answers explain themselves so you learn from them.
Before you start
Code notes in the lessons carry a "Check your local code" tag, because requirements depend on the NEC edition your jurisdiction has adopted and on local amendments.
Lessons are free study material. Finishing one does not certify a skill, count toward a license or replace hands-on training under qualified supervision.
Put it to work
Electrician Jobs Near Me helps electrical contractors hire. When you are ready, see what is open near you or plan your next step.