Conduit · Virtual lab · Beginner · about 22 minutes
Conduit Bending: The 90° Stub-Up in EMT
A stub-up is the bend every electrician makes first and makes most: a 90 that turns a run of conduit up a wall and into a box. Learn why the mark goes at the stub height minus the take-up, then bend one yourself in a 3D workshop that grades the stub you made.
You will learn:
- How a stub-up's height is measured, from the back of the bend to the end
- Why EMT's trade size is a name and what the tubing measures across
- What take-up is and why the mark goes at the stub height minus the take-up
- Which way the hook faces and where the arrow goes
- How a quarter inch at the mark or the arrow becomes a quarter inch at the stub
- How to check a 90 with a level and read what an underbend or overbend does
What this model assumes
- The tube keeps a round cross-section and its centerline keeps its length through the bend. Real EMT stretches a little on the outside of a bend and squeezes on the inside; the centerline model is what bending tables are built on.
- There is no springback: the tube holds exactly the angle where you stop. Klein Tools' guide says some overbending may be needed on real conduit, and no maker publishes an amount for EMT.
- The bend is a circular arc at the bender's published centerline radius, and the arrow sits where that maker's published take-up puts it. The lab's bender is a generic tool built from those two numbers, so read the marks on your own tool.
- The leg on the floor stays still while the bender rolls along it, the way a floor bend is made with the handle up. Air bends are left for the offset lesson.
- The lab's tolerances, 1/8 in on height and 1° on the angle, are practice numbers. They are not a trade, code or examination standard.
What a stub-up is and how it is measured
A stub-up is a 90° bend that turns a run of conduit from one surface onto another: up a wall from the floor, down from a ceiling, or up out of a slab into a panel. Klein Tools' Conduit Bender Guide calls it the most common bend and the building block for the rest, because a back-to-back bend, a box offset and most layouts start from the same arithmetic.
A stub is specified by its height, measured from the back of the bend to the end of the conduit. The back of the bend is the outside of the other leg. With the run lying on the floor, that outside surface sits on the floor, so a 12 in stub has its end 12 in above the floor. Measure a finished stub the same way: hold the tape against the end and read it at the floor, along the back of the run.
Before any of that, know what you are bending. Electrical metallic tubing (EMT) is thin-wall galvanized steel tubing, sold in 10 ft lengths. Its trade size is a name, so 1/2 in EMT does not measure half an inch anywhere. The table gives the outside diameter and wall of the sizes this lesson uses, as the tubing makers publish them under the EMT standard.
| Trade size | Outside diameter | Wall | Inside diameter |
|---|---|---|---|
| 1/2 in | 0.706 in | 0.042 in | 0.622 in |
| 3/4 in | 0.922 in | 0.049 in | 0.824 in |
| 1 in | 1.163 in | 0.057 in | 1.049 in |
A hand bender is a cast head on a steel handle. Its shoe is a grooved arc the tube wraps around. The hook at one end of the shoe catches the tube and points at the free end, the end that will rise. Next to the hook, an arrow cast on the shoe is the reference for a stub-up. Along the shoe toward the heel run the rim notches that mark the center of a saddle's bend, the star point for back-to-back bends and the degree lines for partial bends. At the far end, the heel carries a foot step, and the take-up for a 90 is cast on the head.
Why the bender takes up length
Put the bender's arrow on a mark and roll the tube up to 90. The tube between the mark and the end stays straight and stands up. Below the mark, the tube wraps the shoe, and that curve lifts the mark off the floor. When the stub is plumb the mark stands at a height the bender sets, the same every time for that bender and size. That height is the take-up. Klein Tools casts it on each head as the stub height; Greenlee calls it the deduct and casts it beside the arrow.
So the finished stub is the straight piece you measured plus the take-up the bend adds under it. Turn that around and you have the layout rule every electrician carries: measure from the end and mark at the stub height minus the take-up.
| Conduit | Take-up | Radius, Klein Tools | Radius, Greenlee |
|---|---|---|---|
| 1/2 in EMT | 5 in | 4-5/8 in (51606) | 4-3/16 in (840A) |
| 3/4 in EMT | 6 in | 5-1/2 in (51607) | 5-1/8 in (841A) |
| 1 in EMT | 8 in | 7-3/8 in (51605) | 6-1/2 in (842A) |
Interactive: Watch the take-up happen
Klein Tools' own example: an 8-1/2 in stub in 3/4 in EMT
Given: 3/4 in EMT; Stub height 8-1/2 in; Take-up 6 in
- Mark = stub height minus take-up
- 8-1/2 in minus 6 in = 2-1/2 in
- Mark the conduit 2-1/2 in from the end, put the arrow on the mark with the hook toward that end, and bend to 90
Answer: Mark at 2-1/2 in from the end
Both makers publish the same take-up for each size; their radii differ. In the ideal model the lab uses, the tube's centerline follows a circle around the bender's center, and after a 90 the mark sits one centerline radius plus half the tube's outside diameter above the floor, plus however far the arrow sits ahead of where the curve begins. For Klein Tools' benders that sum lands within a few hundredths of an inch of the take-up, so the arrow marks the start of the curve. For Greenlee's it falls about half an inch short, so on those heads the arrow sits a little ahead of the curve. Neither maker's documents explain the difference, and the lab keeps each maker's take-up exact.
Predict before you bend
Three setups, three predictions. Commit to an answer, then make the bend in the lab below and see it come out the way the arithmetic says.
Predict first
You need a 12 in stub in 1/2 in EMT and mark the conduit at 12 in, forgetting the take-up. With the arrow on that mark and a perfect 90, how tall is the stub?
- 12 in
- 7 in
- 17 in
- It depends on how long the stick is
What happens
17 in. The bend adds its 5 in take-up under whatever straight piece you marked, so marking at the full height gives the full height plus the take-up. Try it: In the lab, mark at the stub height instead of the stub height minus the take-up and grade the result.
Predict first
Your mark is right, but the arrow sits 1/4 in past the mark, away from the end. What happens to the stub?
- It comes out 1/4 in short
- It comes out 1/4 in tall
- Nothing changes, because the hook sets the height
What happens
It comes out 1/4 in tall. The bend forms behind the arrow, so everything from the arrow to the end becomes stub; a quarter inch more tube ahead of the curve is a quarter inch more height. Try it: Set the bender a quarter inch off the mark in practice mode and read the feedback after grading.
Predict first
Everything is set up right, but you stop the bend at 85° instead of 90°. Where is the end of the stub?
- Exactly at the target height, just leaning
- A little lower than the target, and leaning away from the bend
- Higher than the target
What happens
A little lower, and leaning. An underbent stub tips away from the bend, so its end is both off plumb and short of the height a true 90 would reach. A level on the stub shows it at once. Try it: Stop short of 90 in the lab, put the level on the stub and watch the bubble.
The bending lab
Open the lab to work in a 3D training bay: a stick of EMT on a concrete floor, a 4 in square box on a plywood board, a tape, a marker, a hand bender and a torpedo level. Guided mode walks every step and shows the numbers. Practice mode gives you a new height each time with only what a real tape and level would tell you. Challenge mode picks the size and the height, may hand you the bender turned the wrong way, and grades the stub you bent.
Interactive: The 90° stub-up bending lab
- Make a stub on target in guided mode, then switch to practice and do it without the numbers.
- Mark at the full stub height on purpose and see how far off the stub lands.
- Turn the bender around before you bend and watch which end rises.
- Stop at 85° and at 95°, put the level on the stub and compare what the bubble shows.
- Use the See-through and Cut away views to see where the tube sits in the shoe's groove.
Work the numbers
Two checks. First find the parts that matter for a stub-up on a drawing of the lab's bender. Then work out the mark for three stubs, the way you would on a job, from the stub height and the take-up.
Challenge: Find the parts of the bender
Tap each part on a drawing of a hand bender at rest on EMT: the arrow, the hook, the star point and the foot step at the heel. Each answer explains what the part does in a stub-up.
Challenge: Where does the mark go?
Three stubs: 10 in in 1/2 in EMT, 14-1/2 in in 3/4 in EMT and 9-3/4 in in 1 in EMT, all with the makers' published take-up. Type the mark distance from the end; the answer is checked against the take-up table.
A 14-1/2 in stub in 3/4 in EMT
Given: 3/4 in EMT, take-up 6 in; Stub height 14-1/2 in
- Mark = 14-1/2 in minus 6 in
- = 8-1/2 in from the end
- Arrow on the mark, hook toward the end you measured from
- Bend to 90 and check it with a level
Answer: Mark at 8-1/2 in; the finished stub stands 14-1/2 in
On the job
Read your own bender. The take-up is cast on the head, and it is the number to use for that tool. The radius is where benders differ: Klein Tools' 1/2 in Angle Setter bender bends at 4-5/8 in on the centerline and Greenlee's 840A at 4-3/16 in, so the arrow, the star and the degree lines sit in different places on each head. Learn the marks on the tool in your hands, and check a new bender with a test bend.
Keep the tube from sliding. For a floor bend, Klein Tools' guide says to make sure the conduit is secure, put the pressure on the heel with your foot, and use the handle as a guide more than a lever. The tube should roll around the shoe in the groove; if it slips, the arrow leaves the mark and the stub grows or shrinks by the slip.
Read the angle the way your bender's maker says. Greenlee's guide reads a handle-up bend by sighting straight down over the head and stopping when the sight pin lines up with the angle mark; the lab's bender works the same way. For a 90, check the stub with a level. Expect a little springback: Klein Tools' guide notes that some overbending may be needed so the conduit comes to rest at the angle you want, and Greenlee's describes working an overbent stub back with the handle.
Measure from the right end. The end you measure from is the end that stands up, and the hook points at it. When the stub is done, the long leg is cut to length with a tube cutter or a hacksaw, and the cut end is reamed so the edge cannot damage wire pulled through it.
Check your understanding
1. What take-up do Klein Tools and Greenlee publish for a 90° stub-up in 1/2 in EMT?
Answer: 5 in. Both list 5 in for 1/2 in EMT, 6 in for 3/4 in and 8 in for 1 in. Their bend radii differ, so read the marks on your own head.
2. You need a 10 in stub in 3/4 in EMT on a bender with a 6 in take-up. Where is the mark?
Answer: 4 in from the end. Mark at the stub height minus the take-up: 10 in minus 6 in leaves 4 in from the end.
3. Which way does the hook point for a stub-up?
Answer: At the free end you measured from, the end that rises. The hook points at the free end, the end you measured from, and that end rises. Turned the other way, the long end comes up instead.
4. A stub's height is measured from where to the end of the conduit?
Answer: The back of the bend, which is the floor for a run on the floor. Stub height runs from the back of the bend, the outside of the other leg, to the end. With the run on the floor that is the floor.
5. Why does 1/2 in EMT measure 0.706 in across the outside?
Answer: Trade size is a name; the outside diameter is set by the tubing standard. Trade sizes are names. The EMT standard sets 1/2 in EMT at 0.706 in across the outside, and the bender's groove is cut to fit it.
Where this knowledge gets used
- Commercial openings: Most EMT is run in commercial buildings, where bending a clean stub is everyday work.
- Apprentice openings: Bending is one of the first skills an apprentice is trusted with on a crew.
- Starting as an electrician apprentice: What apprentices learn first and how the role grows.
Sources and further reading
Klein Tools
Conduit Bender Guide (Conduit Bending Basics)The take-up table, the stub-up method, the bender's markings, the floor and air bending technique, the springback note and the safety notes.
United States, EMT and rigid conduit hand benders. 12-page PDF, March 2012.
Klein Tools
Angle Setter conduit bender full assemblies 51606, 51607 and 51605, product pagesThe centerline radius of Klein Tools' 1/2, 3/4 and 1 in EMT benders and Klein's eye protection warning.
United States. Product pages as read on the verification date.
Greenlee
Use Guide, Aluminum and Iron Site-Rite Single and Dual Shoe Hand Benders (52034125 REV 02)Greenlee's radius and deduct for each size, how the angle marks are read, correcting an overbend, and the safety statements.
United States. REV 02, 04/23.
Atkore (Allied Tube & Conduit)
EMT Submittal Package (E-Z Pull EMT)The outside diameter, wall and standard length of EMT.
United States, UL 797 and ANSI C80.3. PDF dated 2024-05-29.
National Fire Protection Association
NFPA 70, National Electrical Code (NEC)The EMT bend rules in Article 358 and the bend radius table in Chapter 9, cited by number.
United States; adopted by jurisdiction. 2026 edition issued August 2025; the 2023, 2020 and 2017 editions remain in force in many states; each state adopts its own edition and amendments.
Lessons are free study material. Finishing one does not certify a skill, count toward a license or replace hands-on training under qualified supervision.