Residential · Virtual lab · Intermediate · about 35 minutes
EV Load Calc Lab: Can This Panel Take a Charger?
Before a charger goes on the wall, someone has to show the service can carry it. Watch a house go up with its big loads, then walk the calculation electricians use for an existing house one step at a time, with every load stacked on a tower drawn to scale.
You will learn:
- How the existing-house method turns a house into one number: lighting by living area, kitchen and laundry circuits, appliances at nameplate
- Why the demand factor counts the first 8,000 VA in full and the rest at 40 percent, and what changes when heating or cooling is added
- How an EV charger is counted, and why the 2023 edition's 7,200 VA minimum changes the answer for a small charger
- How to compare the result with the service rating, and what to do when a charger won't fit: a lower setting, energy management or a bigger service
- How to size the charger's breaker and conductors at 125 percent of its setting
- When a year of meter data can replace the room-by-room count
What this model assumes
- The house is the training house from the home page and the house lesson, drawn as a cut-away model. The numbers come from the worked example you pick, so the picture stands for any house and its size on screen does not change the calculation.
- The calculation runs at 240 V. Appliances count at their nameplate ratings, and a nameplate in watts is taken as the same number of volt-amperes, which holds for the resistive loads in a house.
- Existing heating or cooling counts with the other loads, at 40 percent beyond the first 8,000 VA, the way most electricians read the method. Some inspectors want it at 100 percent, and the field calculator has a switch for that.
- The charger counts with the other loads too. Some inspectors want it added at 100 percent because it runs for hours, and the field calculator has a switch for that as well.
- An energy management system is modeled as a fixed cap on the charger. Real systems watch the house and adjust the charger as it runs, and the cap they may be credited with depends on their listing and on the inspector.
- The load tower is the calculation drawn to scale, 4 in of height for every 1,000 VA, so a 100 A service stands as tall as the house's walls. It does not show current in the wires; the glow on each circuit only shows its share of the load.
- Conductor sizes are left out on purpose. The conductor is chosen from the ampacity table for its insulation, the terminals' temperature rating and the conditions of the run.
- The chargers are drawn from their makers' published dimensions. The makers did not make or check the models, and a maker's own manual governs its installation.
What the load check answers
A service has a rating: 100 A, 150 A, 200 A. A charger is a big load that runs for hours, so before one goes on the wall someone has to show the service can carry the house and the charger together. Adding up every nameplate in the house does not answer it. A 2,000 sq ft house with an electric range, a dryer, a water heater and central air adds up to 37,000 VA, half again what a 100 A service is rated for, and that house runs fine every day.
The reason is that loads don't all run at once. The range is rarely at full heat while the dryer runs, the water heater recovers and the air conditioner starts. So the method for an existing house counts the loads, then applies a demand factor: the first 8,000 VA counts in full and everything after it counts at 40 percent. The result is the calculated load. Divided by 240 V it becomes amps, and the amps are compared with the service rating.
- General lighting: the living area times 3 VA per square foot, measured from the outside of the walls, with the garage left out.
- Kitchen and laundry circuits: 1,500 VA each, and at least three of them.
- Fixed appliances: the range, the dryer, the water heater and other fastened-in-place loads at their nameplate ratings.
- The charger: its setting times 240 V, with a 7,200 VA minimum in the 2023 edition.
- The demand factor: the first 8,000 VA in full, the rest at 40 percent.
- The comparison: the calculated load divided by 240 V, against the service rating.
Walk the calculation on the house
The lab builds the house on its blueprint, then walks the calculation one step at a time. As each load is counted it lights up in the house, its circuit glows back to the panel, and it drops onto the load tower behind the house as a block drawn to scale. At the demand step the tower closes up above its first 8,000 VA. At the service step a line appears at the service rating, and the tower either stays under it or breaks through.
Interactive: EV Load Calc Lab
- Pick Tight fit and step to the demand factor: watch the tower close up, then step once more to see how close it comes to the 100 A line.
- Pick Bigger charger: the charger goes from 40 A to 48 A and the house goes just over.
- Pick Edition matters and switch the code edition between 2023 and 2020: only the charger's line moves.
- Tap a gold ring on any load to see its line of the calculation.
Predict before you count
Commit to an answer first. Then let the lab work it out.
Predict first
The 2,000 sq ft house with a 12 kW range, a 5 kW dryer, a 4.5 kW water heater and a 5 kVA air conditioner adds up to 37,000 VA before any charger, more than the 24,000 VA a 100 A service is rated for. Will it take a 40 A charger?
- No, it is already over
- Yes, just
- Only with a bigger service
What happens
Yes, just. With the charger the loads add up to 46,600 VA, but after the demand factor the house calculates to 23,440 VA, or 97.7 A. The first 8,000 VA counts in full and the other 38,600 VA counts at 40 percent. Try it: Pick Tight fit and step to the demand factor and then the service line.
Predict first
The owner sets the same charger to 48 A instead of 40 A, which adds 1,920 VA. What happens?
- It still fits
- It goes just over
- It goes over by more than 10 A
What happens
It goes just over, to 100.9 A on the 100 A service. The extra 1,920 VA lands above the first 8,000 VA, so it only counts at 40 percent, 768 VA, but the house had only 560 VA of room left. Try it: Pick Bigger charger, or set the charger to 48 A in the controls.
Predict first
A 700 sq ft house adds a 16 A charger, a nameplate of 16 A × 240 V = 3,840 VA. Under the minimum the 2023 edition added for chargers, what does it count for?
- 3,840 VA
- 7,200 VA
- 9,600 VA
What happens
7,200 VA. The 2023 edition counts a charger at its nameplate or 7,200 VA, whichever is larger. That rule sits in the standard method, and inspectors differ on applying it in the existing-house method, so the lab lets you switch it. The 2020 and 2017 editions have no minimum, and the same charger counts 3,840 VA. Try it: Pick Edition matters and switch the code edition, then turn the 7,200 VA minimum off in the controls.
Change the house and the charger
Open Change the house in the lab and move one thing at a time. The living area moves the lighting line by 3 VA a square foot. Gas cooking or drying takes a whole appliance off the list. A bigger service raises the line on the tower. Every change runs the same engine the field calculator uses, so the worksheet always matches it.
The charger list holds real home chargers, drawn from their makers' published dimensions. Put one on the wall and the lab counts it at its largest setting; the setting chips show what else it can be set to. Most home chargers are set by the installer to match the breaker, and that setting is the number the calculation counts. Move the charger outside and the car parks in the driveway. Where the charger hangs changes its run, and its load stays the same.
Interactive: Compare home chargers
When a charger won't fit, there are three ways out. Set it lower, so it draws less and its breaker gets smaller too. Add a listed energy management system that watches the house and holds the charger back, so the calculation can count the cap instead of the charger's full setting; the charger's own circuit stays sized for its setting. Or upgrade the service. Try each one on the Bigger charger example.
Make it fit
Three problems from the field. Each one checks your answer with the same engine as the lab.
Challenge: Turn the charger down until it fits
The tight-fit house with a charger that can be set to 48 A, on a 100 A service. Pick the largest setting that keeps the calculated load at or under the service rating.
Challenge: Size the charger's breaker and conductors
For chargers set to 48 A and then 40 A, pick the smallest standard breaker and the smallest conductor ampacity the circuit may have.
Challenge: Which fix brings the house under?
A house replacing its air conditioner with a 10 kVA heat pump while it adds a 40 A charger calculates to 131 A on 100 A. Try five fixes and find the one that works.
Worked example: the tight fit, line by line
Given: 2,000 sq ft of living area; Two kitchen circuits and one laundry circuit; Range 12 kW, dryer 5 kW, water heater 4.5 kW; An existing 5 kVA air conditioner, kept; A charger set to 40 A, on a 100 A service
- General lighting: 2,000 × 3 VA = 6,000 VA
- Kitchen and laundry: 3 × 1,500 VA = 4,500 VA
- Appliances: 12,000 + 5,000 + 4,500 = 21,500 VA, and the air conditioner at 5,000 VA
- Charger: 40 A × 240 V = 9,600 VA, more than the 7,200 VA minimum
- Total: 46,600 VA. The first 8,000 VA counts in full, and the other 38,600 VA × 0.40 = 15,440 VA
- Calculated load: 8,000 + 15,440 = 23,440 VA, and 23,440 VA ÷ 240 V = 97.7 A
- The charger's circuit: 40 A × 1.25 = 50 A, so a 50 A breaker and conductors of at least 50 A ampacity
Answer: 97.7 A on a 100 A service: it fits, with 2.3 A to spare
On the job
On a real call the inputs come from the house. Read the service rating on the main breaker and the meter base, and see that the service conductors match it. Measure the living area from the outside dimensions. Read the nameplates on the range, the dryer, the water heater and the heating and cooling equipment; where a nameplate is missing, the maker's data is the next best source. Ask whether any heating or cooling is changing in the same job, because that changes the method.
If the utility can provide a year of the house's maximum demand, or a recording meets the 30-day rules, the measured method can replace the room-by-room count. The highest demand in the records counts at 125 percent, and the charger goes on top in full. Solar panels, a wind turbine or peak shaving on the service change that, and the editions disagree: the 2017 edition sets no limit, the 2020 edition bars the method for them, and the 2023 edition allows it only with a full year of data. Pick Meter data in the lab to see it: the tower becomes one block for the house and one for the charger, and without qualifying data the lab refuses the method, the way an inspector would.
Whichever method you use, write the inputs and the result down. The lab's Copy the numbers button and the field calculator both give a plain-text record of every line, which is the start of what an inspector or the utility will ask for. Then size the charger's circuit: a breaker of at least 125 percent of the charger's setting, conductors for at least the same 125 percent, a disconnecting means where the equipment calls for one, and GFCI protection when the charger plugs into a receptacle.
Charger installs are everyday work for residential electricians, and running this check on site is how a job gets quoted right the first time. See EV charging jobs, or take the EV-Ready skills check to show what you know.
Check your understanding
1. Under the minimum the 2023 edition added for chargers, what does a 16 A charger count for?
Answer: 7,200 VA. 7,200 VA. The 2023 edition counts a charger at its nameplate or 7,200 VA, whichever is larger, and 16 A × 240 V is only 3,840 VA.
2. What is the smallest standard breaker for a charger set to 48 A?
Answer: 60 A. 60 A. A charger is a continuous load, so its breaker is at least 125 percent of its setting: 48 A × 1.25 = 60 A, which is a standard size.
3. In the existing-house method, what share of the load beyond the first 8,000 VA is counted?
Answer: 40 percent. 40 percent. The first 8,000 VA counts in full and the rest at 40 percent, because a house never runs every load at full power at once.
4. A house calculates to 97.7 A on its 100 A service with a 40 A charger. With the charger at 48 A it calculates to 100.9 A. Which of these does not bring it back under?
Answer: Mounting the charger outside. Mounting it outside. Where the charger hangs changes its run, and its load stays the same. A lower setting, a cap from a listed energy management system or a bigger service each bring the calculated load under the rating.
5. What does the measured method need before it can replace the room-by-room count?
Answer: A year of maximum demand data, or a recording that meets the 30-day rules. A year of maximum demand data, or a continuous recording that meets the 30-day rules. The highest demand then counts at 125 percent, with the charger added on top.
6. Why is the garage left out of the general lighting load?
Answer: The lighting load counts living area only, measured from the outside dimensions. The general lighting load counts the living area, measured from the outside dimensions, without the garage, open porches or unfinished space that can't be used later.
7. A house is replacing its air conditioner with a heat pump in the same job as the charger. What changes in the calculation?
Answer: The larger of the heating or cooling counts at 100 percent on top of the demand factor. With heating or cooling being added, the larger of the two counts at 100 percent on top, instead of at 40 percent with the other loads. That is why the heat pump puts the house over, more than the charger does.
Where this knowledge gets used
- EV charger openings: Contractors who install home and commercial chargers need electricians who can run this check on site.
- EV charging work near you: Openings at contractors that install EV chargers, by state and city.
- The EV-Ready skills check: A short timed check of the charger load calculation and circuit sizing, with a badge to show employers.
Sources and further reading
National Fire Protection Association
NFPA 70, National Electrical Code (NEC)The existing dwelling calculation, the 7,200 VA minimum for EVSE in the 2023 edition, energy management in load calculations, the individual branch circuit, overcurrent protection and conductors at 125 percent, the disconnecting means and GFCI protection for EV charging, and how each changed between the 2017, 2020, 2023 and 2026 editions, cited by number for the reader to check.
United States; adopted by jurisdiction. 2026 edition issued August 2025; the 2023, 2020 and 2017 editions remain in force in many states; each state adopts its own edition and amendments.
National Fire Protection Association
NEC enforcement mapsWhich edition each state enforces, the reason the lab offers three editions.
United States. As of August 3, 2026.
Lawrence Berkeley National Laboratory
NEC load calculations and home electrification, DOE codes webinar slidesHow the existing dwelling method counts chargers and heating, and why the 2026 edition changes it.
United States; NEC. April 18, 2024.
Mike Holt Enterprises
Understanding the 2023 NEC, Volume 2: 625.40 sampleThe 2023 change to the individual branch circuit for EV charging.
US; NEC 2023. 2023 edition.
Tesla
Wall Connector installation manual: product specifications and circuit breaker ratingsThe Tesla Wall Connector's settings, breakers, size, cable, enclosure and power sharing.
North America. Online manual, 2026.
ChargePoint
ChargePoint Home Flex specifications and ordering informationThe ChargePoint Home Flex's settings, its 70 A breaker at 50 A, plug-in limits, size and enclosure.
North America. April 2025.
Wallbox
Pulsar Plus installation guide (North America)The Wallbox Pulsar Plus's current selector, breakers, size and load sharing.
North America. V3, August 28, 2025.
Emporia
Pro EV Charger sell sheetThe Emporia Pro's settings, minimum breakers, size and load management.
North America. 2025 to 2026.
United Chargers
Grizzl-E Classic user manualThe Grizzl-E Classic's DIP switch settings, breakers, size and enclosure.
North America. V3.5, 2024.
Ford Motor Company
Ford Charge Station Pro installation guideThe Ford Charge Station Pro's 80 A setting, 100 A breaker, disconnect and size.
North America. R10, April 2025.
Autel Energy
MaxiCharger AC Elite (Residential) user manualThe Autel MaxiCharger's current selector, its 70 A breaker at 50 A, size and weight.
North America. V2.1, May 2024.
Enphase Energy
IQ EV Charger 2 data sheet (North America)The Enphase IQ EV Charger 2's models, breakers, size and load balancing.
North America. June 2026.
Furniture in this lesson is adapted from the Amazon Berkeley Objects dataset. Credit for the data, including the 3D models, goes to Amazon.com. The dataset was built by Matthieu Guillaumin, Thomas Dideriksen, Kenan Deng, Himanshu Arora, Arnab Dhua, Xi (Brian) Zhang and Tomas Yago-Vicente of Amazon.com, and Jasmine Collins, Shubham Goel and Jitendra Malik of UC Berkeley. The television is adapted from NVIDIA SimReady Assets. Both are licensed under CC BY 4.0 and provided as is, with no warranty. Web-ready versions were prepared by CodePawl (ABO, SimReady). We changed the files: simpler shapes, smaller textures, new file names, names and metadata removed. Amazon, NVIDIA and CodePawl did not make this lesson and do not endorse it or Electrician Jobs Near Me.
Lessons are free study material. Finishing one does not certify a skill, count toward a license or replace hands-on training under qualified supervision.