Distribution · Equipment explorer · Beginner · about 15 minutes
The Electrical Panel in Three Dimensions
A panel drawing shows where things are. Depth shows what sits on what: the bus under the breakers, the rails their ends hook onto, the bars on the insulating base, the cover over all of it. The model below follows one real product, a Square D QO plug-on neutral load center, drawn from the dimensions Schneider Electric publishes. Turn it, take it apart, build it back in order and make a breaker trip.
You will learn:
- What sits in front of what inside a real load center, from the back of the box to the cover
- How a QO breaker mounts: its load end hooks a rail, its line end grips the row's bus connector, and the rows alternate legs
- What a plug-on neutral rail does, and why an AFCI can skip the pigtail a GFCI still carries
- The order a panel goes together, and which pieces arrive fitted from the factory
- How current, an overload, a short circuit and a fault to a grounded case look on the actual parts
What this model assumes
- The model follows one product: Square D QO130M200PC, a 200 A plug-on neutral load center with 30 spaces, drawn from Schneider Electric's published dimension drawing, catalog, installation bulletins and product pages. The box, the breakers, the main breaker, the ground bar kit, the bonding screw and the cover are their published sizes. The interior's heights and the places of its bars and lugs are scaled from Schneider's photographs, and the bus bars under the shield are drawn from the wiring diagram. Square D and QO are trademarks of Schneider Electric, which did not make or check this model.
- The breakers are the panel lesson's example circuits, each in the row that lesson's engine gives it, spread across both columns. The branch conductors follow one tidy installation of our own; Schneider does not publish a wiring layout.
- Every electrical number comes from the lab's engines: loads, bus and neutral currents, heating and trips from the panel lesson's engine, and the ground-fault and arc-fault responses from the circuit protection lesson's engine. The model only draws them.
A panel is built in layers
Open a real load center, with the power off and the cover removed by a qualified person, and you see a flat face: breaker handles in two columns, a main at the top, bars beside it. The face hides the order underneath. Against the wall is the steel enclosure, 14.25 in wide and 29.86 in tall for this panel. Screwed to its back is the interior: a molded base carrying two tin-plated copper bus bars under an insulating shield, one bar per leg, with a short bus connector for each of the 15 rows. The main breaker sits at the head of the bus. The neutral bars stand on the insulating base beside it, and a plug-on neutral rail runs down the outer end of each column of breakers. The breakers plug onto the connectors and hook onto the rails, and the cover goes over everything, leaving only the handles in reach.
The drawing in the panel lesson spreads those layers sideways so each one can be seen. The model on this page keeps them where they are. It follows one product, Square D catalog number QO130M200PC, built from Schneider Electric's dimension drawing, catalog, installation bulletins and product pages, so the box, the breakers, the main, the ground bar kit and the cover are their published sizes. Its circuits are the panel lesson's example panel, and every current and every trip comes from the engines behind that lesson and the circuit protection lesson.
Turn the panel, take it apart
The model opens on request, so the page stays light. Once it is open, drag sideways to turn it, pinch or scroll to zoom, and tap any piece, any breaker, or its name in the lists to find out what it is. The Front view is the flat elevation, the same picture as a drawing; switch to the three-quarter view and the lens opens. The close-ups go to the service end, the bus connectors, the way a breaker mounts and the wiring gutter, and the exploded view lifts every piece away from the wall in the direction it comes out.
Interactive: The load center in three dimensions
Look for three things while it is open. Every row has one bus connector at the center and both columns plug onto it, so the leg depends on the row: row 1 is leg A, row 2 leg B, and so on down. Every breaker's load end hooks the rail 70 mm from its line end, where Schneider's drawings put the clip. And the green screw at the top of a right-hand neutral bar is the one place the neutral and the steel meet.
The What happens if controls run the panel lesson's engine and the protection lesson's engine on this panel. Overload the kitchen circuit and its thermal element warms for about 7 minutes, played in a few seconds, until the handle drops to the center and the trip indicator shows. Short it and the magnetic element opens in about one cycle. Touch a hot conductor to a grounded case and the fault current runs home on the bare conductor, through the ground bar, the steel of the box and the green screw to the neutral. Each event is worked out in real seconds before it plays, then shown slowed down or sped up, so the clock under the model always gives the real time the event takes, and the table beside it compares the currents before, during and after. Turn on Current to see it move. More tools has the close-ups, See inside for the bus shield, the breaker cases and the cover, and Color the legs; pick any part and Show puts it alone, or with only the parts it touches.
Call it before you turn it
Two questions the model can settle. Commit to an answer first.
Predict first
With the cover off, which piece stands furthest out from the wall?
- The bus connectors
- The branch breakers
- The neutral bars
What happens
The breakers plug onto the bus connectors and stand proud of everything behind them, which is why the cover's trim needs openings only for their handle housings. Try it: turn the model to the side view with the cover off and look along a column.
Predict first
The lighting breaker sits in row 6 of the left column, circuit 11. Which leg does its bus connector come from?
- Leg A, like row 5
- Leg B, the other leg from the rows above and below it
- Both legs
What happens
Rows alternate down the panel, A, B, A, B. Row 6 is even, so its connector rises from bus B, and a breaker beside it in the right column, circuit 12, would be on leg B as well. Try it: open More tools, pick See inside: Bus shield and Color the legs, then follow row 6 from its stab down to its bar.
Build it in order
The second model starts as an empty enclosure on the wall. Move the build slider and the pieces arrive in the order the panel goes together: the factory interior with its bus, main, neutral bars and rails, then the ground bar kit, the bonding screw, the service conductors, the breakers, the branch conductors and the cover. Each breaker arrives the way Schneider's bulletin says to install one: load end hooked onto the rail, then swung down onto its bus connector.
Interactive: Build the panel in order
| Step | Piece | Fitted by |
|---|---|---|
| 1 | Enclosure | Electrician |
| 2 | Interior: bus, shield and bus connectors | Factory |
| 3 | Main breaker | Factory |
| 4 | Neutral bars | Factory |
| 5 | Plug-on neutral rails | Factory |
| 6 | Equipment ground bar kit | Electrician |
| 7 | Main bonding jumper, the green screw | Electrician |
| 8 | Service conductors | Electrician |
| 9 | One-pole breakers | Electrician |
| 10 | Two-pole breakers | Electrician |
| 11 | GFCI and AFCI breakers | Electrician |
| 12 | Branch circuit conductors | Electrician |
| 13 | Cover | Electrician |
Two things worth trying. Stop at step 8, with the service conductors landed and no branch breakers in place: once the utility connects, the full service voltage sits on every bus connector, so the panel stays covered and nobody but qualified people with the power off goes near the interior. Then run the slider back from step 13 and notice that the cover is the first thing off and the conductors and breakers the next: service work follows the build order in reverse.
What depth tells you that a drawing cannot
Look at a breaker from the end of its row and the drawings come to life. A QO breaker is 19 mm wide per pole and about 76 mm from its line end to its load end; the AFCI here is 121 mm and the GFCI 105 mm, because their electronics ride at the load end. At the line end a spring jaw grips the row's bus connector. Seventy millimeters out, a clip under the load end grips the plug-on neutral rail. On a standard breaker that clip holds the breaker in place. On a plug-on neutral breaker it is also the neutral connection, which is why the bedroom AFCI has no pigtail while the bathroom GFCI, a pigtail model, carries a coiled white lead to the neutral bar.
| Row | Directory number | Circuit | Breaker | Leg |
|---|---|---|---|---|
| 1 | 1 | Kitchen small appliance | QO120, 20 A, one pole | Leg A |
| 2 | 4 | Bedroom outlets | QO115PCAFI, 15 A AFCI, one pole | Leg B |
| 3 and 4 | 5 and 7 | Range | QO250, 50 A, two pole | Leg A and leg B |
| 5 | 10 | Bathroom | QO120GFI, 20 A GFCI, one pole | Leg A |
| 6 | 11 | Lighting | QO115, 15 A, one pole | Leg B |
| 7 and 8 | 14 and 16 | Dryer | QO230, 30 A, two pole | Leg A and leg B |
Directory numbers run odd down the left column and even down the right, and both columns of a row share one bus connector, so circuit 1 and circuit 2 are always on the same leg. That is how the panel lesson's rule, positions alternate A, B, A, B, looks on a real two-column panel: a two-pole breaker takes two rows of one column, and the range in rows 3 and 4 gets one pole on each leg and the 240 V between them.
The bars tell a second story. The neutral bars sit on the insulating mains base, so the neutral touches the steel in exactly one place: the green bonding screw, 1/4-20 by 1 in, through the top hole of a neutral bar and into the back of the box. The ground bar kit has no insulation; it screws straight to the back, because its whole purpose is to be the steel. That one difference is why a subpanel, which gets no bonding screw, keeps its neutrals and grounds apart, which the grounding and bonding lesson takes apart in full.
Find it, order it
Two challenges on the same panel. Each one checks your answer at once.
Challenge: Find the part
The lesson names a part of the panel, such as the main bonding jumper or the neutral bar, and you find it on the drawing or pick it from the list.
Challenge: Put it together
Eight moments in a panel's assembly, from the empty enclosure on the wall to the breakers on their rails. At each step, pick what goes in next.
One habit from all of this. When a panel confuses you, read it from the back forward: enclosure, interior and main, bars and rails, bonding screw, conductors, breakers, cover. Every piece in front depends on a piece behind it, and most defects are a piece landed in the wrong layer.
Where seeing the panel in depth pays
Service upgrades, panel changes and subpanel additions are the work where this picture pays first. An electrician who can see the layers knows at a glance whether a breaker is seated on its connector and hooked on its rail, whether the neutrals and grounds are on the right bars, whether the bonding screw belongs, and whether the cover will close. Inspectors read a panel the same way, and so do the estimators who have to price a panel change from a photograph.
The same habit scales up. A commercial panelboard, a switchboard section and a motor control center bucket are the same layers at a larger size: an enclosure, a bus assembly, protective devices clipped or bolted to it, and a cover that leaves only the operators exposed. If this is the kind of work you want more of, the openings below are residential and service roles where panel work is routine.
Check your understanding
1. With the cover off, which piece of the load center stands furthest out from the wall?
Answer: The branch breakers. The breakers plug onto the bus connectors and stand in front of everything behind them. The cover's trim is cut for their handle housings.
2. A one-pole breaker sits in row 5, in either column. Which leg does it draw from?
Answer: Leg A. Rows alternate legs from the top, and both columns of a row share one bus connector. Row 5 is odd, so leg A, and 120 V to the neutral.
3. Where do the neutral and the steel meet in this panel?
Answer: Only at the green bonding screw through a neutral bar. The neutral bars sit on the insulating mains base. At the service the green bonding screw makes the one deliberate connection, which is what turns a fault to a grounded case into a current the breaker can see.
4. Which piece never moves in the exploded view?
Answer: The enclosure. Everything else is mounted to the enclosure, so the enclosure stays on the wall and every other piece lifts away from it.
5. In the build order the model follows, what goes on last and comes off first?
Answer: The cover. The cover, with its dead front trim and door, closes over the finished panel and is the first thing removed for service, by qualified people with the power off.
Where this knowledge gets used
- Residential openings: Panel changes, service upgrades and subpanels are everyday residential work.
- Service and repair openings: Service electricians read a panel in depth before they touch it: seating, bars, bond, cover.
- Working as a journeyman: What journeyman electricians are expected to know and how the role grows.
Sources and further reading
National Fire Protection Association
NFPA 70, National Electrical Code (NEC)Article 408 on panelboards and their enclosures, 250.28 on the main bonding jumper, 110.26 working space and 110.27 guarding.
United States; adopted by jurisdiction. 2026 edition issued August 2025; the 2023, 2020 and 2017 editions remain in force in many states; each state adopts its own edition and amendments.
US Occupational Safety and Health Administration
29 CFR 1910 Subpart S, Electrical (general industry), 1910.303 GeneralGuarding of electrical equipment and working space in general industry.
United States, general industry. Current CFR text as published by OSHA.
Schneider Electric
QO Load Centers, General Purpose NEMA Type 1 Enclosure, Indoor (drawing PWFDS-SYRS-0203)The box outline, keyholes, knockouts, finish, ratings and wiring diagram the model's enclosure and rows follow.
United States. September 2020.
Schneider Electric
Square D QO and Homeline Load Centers and Enclosures Catalog (1100CT0501)Box number 9 dimensions, the shielded tin-plated copper bus, split neutrals, plug-on neutral interiors, the QOM2 main, the ground bar kit and the bonding screw.
United States; UL 67 panelboards. Rev. 03 (file dated 2026-06-24).
Schneider Electric
QO and Homeline Load Centers, Instruction Bulletin S1B33894How a QO breaker hooks the mounting rail and rotates onto its bus connector, the bonding screw through the neutral bar, twistouts and cover screws.
United States and Mexico. 10/2023.
Schneider Electric
QO130M200PC load center, product pageThe product's ratings, spaces, materials, height and width, and the breaker, main, cover and ground bar kit dimensions on the related product pages.
United States. Product page as read on the verification date.
Schneider Electric
QO and QOB Combination AFCI Circuit Breaker (CAFI), Pigtail and Plug-on Neutral, Instruction Bulletin 48840-248-01The plug-on neutral AFCI's neutral connection to the load center rail and the handle tripping to the center position.
United States and Canada. Rev. 06, 09/2020.
UL Standards and Engagement
UL 943, Standard for Ground-Fault Circuit-InterruptersThe Class A ground-fault trip curve the protection engine uses for the bathroom GFCI event.
United States and Canada. Current edition as listed by UL.
Lessons are free study material. Finishing one does not certify a skill, count toward a license or replace hands-on training under qualified supervision.