Home > Electrical Learning Lab > Bending a two-bend offset

Conduit · Virtual lab · Intermediate · about 25 minutes

Conduit Bending: Two-Bend Offsets in EMT

An offset moves a run of conduit over or around something and keeps it going the same way: two equal bends in opposite directions. Learn where the two marks go and why, then bend one in a 3D workshop, the second bend in the air, and set the finished piece on the curb it has to climb.

Builds on Bending a 90° stub-up.

You will learn:

  • What an offset is and where electricians use one
  • How the offset table's multiplier sets the distance between the marks
  • Why the run shrinks and where MARK A goes when working toward an obstruction
  • Which way the hook faces for each bend and why the second bend is made in the air
  • Why both bends have to match and stay in one plane
  • How close the table's arithmetic comes to a real bend at the bender's radius
What this model assumes
  • The tube keeps a round cross-section and its centerline keeps its length through each bend, and each bend is a circular arc at the bender's published centerline radius.
  • There is no springback: each bend holds exactly the angle where you stop. Klein Tools' guide says some overbending may be needed on real conduit.
  • The arrow sits where the maker's published take-up puts it, as in the stub-up lesson, and the hook faces away from MARK B for both bends, as Klein Tools sets up an offset.
  • For the second bend the bender stands still on its handle while the free end is bent around the shoe. If the conduit sits turned off the bender's line, the second bend forms in a plane turned by exactly that much, a dog leg, and the lab shows the twisted piece; it does not model the conduit slipping in the shoe.
  • The curb's distance is measured from the end of the conduit to the curb's face, and the curb is as tall as the offset.
  • The lab's tolerances, 1/8 in on the rise, 1° of parallel and 1/4 in on where the climb levels out, are practice numbers. They are not a trade, code or examination standard.
Understand

What an offset is

An offset is two equal bends in opposite directions. The conduit leaves its run at the first bend, crosses at the bend angle, and turns back parallel to where it started at the second, shifted sideways or up by the offset, also called the offset depth. Klein Tools' Conduit Bender Guide lists the everyday uses: staggered joists, running tight on a wall, offsetting into an electrical box, and changes in elevation.

This lesson's job is a change in elevation. A run of EMT lies on the floor and has to climb onto a concrete curb. The curb's face is a measured distance from the end of the conduit, and the curb is as tall as the offset, so the finished piece has its end leg on the floor and its far leg resting on top of the curb.

Two numbers decide an offset: how far apart the bends are, and the angle of both bends. A steeper angle climbs in a shorter distance. Greenlee's Use Guide puts the trade-off plainly: a steeper bend takes more pulling force, and a shallower bend takes more space. Klein Tools' guide leaves the angle to the installer and notes that the location usually decides what will fit. The lab offers 22.5°, 30° and 45°.

Both bends of an offset are made at the bender's arrow, the same mark used for a stub-up; Klein Tools' guide also uses it for the outer marks of a saddle. The degree lines along the shoe show when each bend reaches its angle.

Explore

The offset table: multiplier and shrink

The distance between the two bend marks is the center to center distance. Picture the two legs and the climb between them as straight lines meeting at sharp corners: the climb is the long side of a right triangle whose short side is the offset. Divide the offset by the sine of the bend angle and you have the climb's length. The makers round that cosecant into a multiplier and print it in a table.

Center to center = offset × multiplier
Greenlee and Klein Tools both work an offset this way.

The climb also uses up run. Measured along the floor, the tube covers less ground than it did straight, so a mark measured from the end lands closer to the end once the offset is bent. That loss is the shrink, and the table gives it per inch of offset. Working toward an obstruction, Greenlee's guide adds the total shrink to the distance so the climb still lands at the obstruction.

Total shrink = offset × shrink per inch
MARK A = distance to the obstruction + total shrink, and MARK B = MARK A − center to center.
Offset multipliers and shrink as the makers print them
Bend angleMultiplierShrink per inch of offsetCosecant of the angle
10°6.01/16 in5.759
15°3.861/8 in3.864
22.5°2.63/16 in2.613
30°2.01/4 in2.000
45°1.43/8 in1.414
60°1.21/2 in1.155

Klein Tools and Greenlee print the same rows; the 15° row is Greenlee's alone. The multipliers are the cosecants rounded for the tape, and the shrink figures run a little under the sharp-corner value, which is the tangent of half the angle. A real bend is a curve, and the explorer below shows how close the arithmetic comes on a real radius.

Interactive: See what the table's numbers do

A side view of 1/2 in EMT climbing onto a curb 26 in from its end, bent on a Klein Tools bender with a 4-5/8 in radius. Pick 22.5, 30 or 45 degrees and the offset height; the drawing shows the finished piece to scale with MARK A and MARK B, and the readout compares the table's multiplier and shrink with the exact values and gives the bent tube's real rise. At 45 degrees and 4 in the marks land at 27-1/2 in and 21-7/8 in and the tube rises 4-1/8 in. The simulator runs in your browser with JavaScript turned on.

Greenlee's worked example: 10 in of 45° offset toward an obstruction

Given: Offset 10 in at 45°: multiplier 1.4, shrink 3/8 in per inch; Obstruction 30 in from the end

  1. Center to center = 10 in × 1.4 = 14 in
  2. Total shrink = 10 in × 3/8 in = 3-3/4 in
  3. MARK A = 30 in + 3-3/4 in = 33-3/4 in
  4. MARK B = 33-3/4 in − 14 in = 19-3/4 in

Answer: MARK A at 33-3/4 in and MARK B at 19-3/4 in from the end

Predict

Predict before you bend

Three setups for the 4 in, 45° offset onto the curb. Commit to an answer, then try it in the lab below.

Predict first

You put MARK A at the curb's distance, 26 in, and forget the 1-1/2 in of shrink. MARK B still goes 5.6 in back from it. Where does the climb level out?

  1. Right at the curb face
  2. 1-1/2 in sooner, short of the curb
  3. 1-1/2 in later, past the curb face
  4. It does not level out
What happens

1-1/2 in sooner. Both marks moved 1-1/2 in toward the end, so the whole offset did too: the rise is the same, but the climb finishes short of the curb and the far leg starts out over bare floor. Try it: In practice mode, mark MARK A at the curb's distance and grade the piece.

Predict first

Your MARK B sits 1 in too close to MARK A, so the marks are 4.6 in apart instead of 5.6 in. How high does the offset come out?

  1. 4 in, the same
  2. About 3/4 in lower
  3. About 1 in lower
  4. About 1 in higher
What happens

About 3/4 in lower. The climb runs at 45°, so an inch less between the bends is the sine of 45°, about 0.71 in, less rise. At 30° it would be half an inch. Try it: Mark B an inch close in practice mode and read the rise in the results.

Predict first

The first bend goes to 45° and you stop the second at 40°. What does the finished piece do?

  1. Nothing; the rise is all that matters
  2. The far leg runs 5° out of parallel and will not sit flat on the curb
  3. The offset gets taller
What happens

The far leg runs 5° out of parallel. The two bends have to match for the legs to come out parallel, so the far leg tips and rests on one point of the curb. Try it: Stop the second bend short in the lab and look at the piece on the curb from the side.

Experiment

The bending lab: an offset onto a curb

Open the lab to work in the same 3D training bay as the stub-up, with a concrete curb behind the bending line. Work out the marks, mark the conduit, set the bender for the first bend on the floor, then turn it over for the second bend in the air. When you are done the piece is set on the curb with its end where you measured from, and the grade compares it with a perfect piece made from the same marks.

Interactive: The two-bend offset bending lab

A full-screen 3D workshop for bending a 22.5, 30 or 45 degree offset in 1/2, 3/4 or 1 in EMT with Klein Tools or Greenlee bender data. Work out the shrink, the center to center distance and both marks from the maker's table, mark them with the tape and marker, set the bender with the hook facing away from MARK B and roll the first bend on the floor, then turn the bender over on its handle, slide MARK B to the arrow and bring the free end around the shoe. The finished piece is set on the curb, and the grade measures the rise, the legs' parallel and where the climb levels out. Works with touch, mouse and keyboard, and falls back to a drawing where 3D is not available. The simulator runs in your browser with JavaScript turned on.
  • Make an offset on target in guided mode, then switch to practice and do it from the table alone.
  • Forget the shrink on purpose and see where the climb lands against the curb.
  • Stop the second bend short and look at the far leg on the curb.
  • Try the same 4 in offset at 30° and at 45° and compare how far apart the marks are.
  • Use the Rise and Run to the curb readouts to measure the piece the way you would with a tape.
Solve

Work the marks

Three offsets to lay out the way you would on a job: the two the makers work in their own guides, and one at 30°. Each needs both marks, measured from the end.

Challenge: Where do MARK A and MARK B go?

Three offsets: Greenlee's 10 in at 45 degrees toward an obstruction 30 in away, Klein Tools' 6 in at 45 degrees with the obstacle 20 in away, and a 4 in offset at 30 degrees onto a curb 24 in away. Type both marks; each is checked against the maker's table.

Klein Tools' worked example: a 6 in offset at 45°

Given: Offset 6 in at 45°: multiplier 1.4, shrink 3/8 in per inch; Obstacle 20 in from the end

  1. Total shrink = 6 in × 3/8 in = 2-1/4 in
  2. First mark = 20 in + 2-1/4 in = 22-1/4 in
  3. Between the marks = 6 in × 1.4 = 8.4 in
  4. Second mark = 22-1/4 in − 8.4 in = 13.85 in, 13-7/8 in on the tape

Answer: Marks at 22-1/4 in and 13-7/8 in from the end

Apply

On the job

Set the bender the way its maker shows. Klein Tools places the bender for the first bend with the hook facing away from the second mark and the arrow on the first mark, then rolls up the free end on the floor to the angle. The long end of the stick is the free end for that bend. Greenlee's steps are the same in substance: the arrow on MARK A, bend, turn the conduit 180°, the arrow on MARK B, bend to the same angle.

Make the second bend in the air. Once the conduit is turned half a turn, the first bend points down, so Klein Tools' guide flips the bender and the conduit together, stands the bender on its handle's hilt, lets the conduit turn half a turn in the cradle, slides it until the second mark is at the arrow, and bends the free end around the cradle until the angle is reached. The half turn is what makes the second bend go the opposite way.

Keep both bends in one plane. Klein Tools' guide warns that if the first bend is not in the same plane as the second, the legs of the offset come out skewed and the piece will not lie flat; some correcting is possible, depending on how far out it is. Line the first bend up with the plane of the second before you bend.

Know which way you are working. Greenlee's guide lays out an offset two ways. Working past an obstruction, MARK A goes where the first bend should start and MARK B one center to center distance farther on. Working toward an obstruction, MARK A goes at the distance plus the total shrink and MARK B one center to center back toward the end, which is the job in this lesson's lab.

Expect the real tube to differ a little from the table. The lab bends each arc at the maker's published radius: on the 1/2 in benders a perfect 45° offset comes out within about 1/8 in of the table's rise, while on the 1 in benders it runs about 1/8 to 3/16 in high. Check the first offset you bend on a new tool, and cut the unbent end to length with a tube cutter or a hacksaw, then ream the cut so it cannot damage wire pulled through it, as Klein Tools' guide says.

Check your understanding

1. What multiplier do Klein Tools and Greenlee print for a 45° offset?

Answer: 1.4. Both print 1.4 for 45°, a rounded cosecant of the angle. Multiply the offset by it to get the distance between the marks.

2. A 5 in offset at 30°: how far apart are the two marks?

Answer: 10 in. Center to center is the offset times the multiplier: 5 in times 2.0 is 10 in.

3. Working toward an obstruction 24 in from the end, you need a 4 in offset at 30°. Where does MARK A go?

Answer: 25 in. MARK A is the distance plus the total shrink: 4 in times 1/4 in is 1 in of shrink, so 25 in from the end.

4. In Klein Tools' guide, which way does the hook face for the first bend of an offset?

Answer: Away from the second mark. Klein Tools places the bender with the hook facing away from the second mark and the arrow on the first mark, then rolls the free end up.

5. What happens if the two bends of an offset are not in the same plane?

Answer: The legs come out skewed and the piece will not lie flat. Klein Tools' guide warns that the legs come out skewed. Line the first bend up before you make the second.

Where this knowledge gets used

Sources and further reading

Lessons are free study material. Finishing one does not certify a skill, count toward a license or replace hands-on training under qualified supervision.