If you’re dying to install your new instructions for how to install a light bar. These instructions include options for installations with or without a wire harness and for connecting to existing LED lights. Installation will vary based on the type of vehicle, existing lighting setup, and chosen wiring method, but these instructions can serve to give you a general idea of the process. Light bar mounting instructions are also available and are listed by WH-DTS10, WWH-DTD30; (ATP) WH-ATPD20, sdoptional mounting brackets; be sure not to overtighten the hardware (you will need to adjust it in step 7).

3. Route the lighting side of the wiring harness from the battery to the light in a safe, secure manner. Connect the harness to the light. Be sure to avoid heat sources and any moving parts while running your wires. Prolonged chafing of the wires may lead to a short in the circuit. Typically, following the vehicle manufacturer’s wiring harness is a safe path to follow. Some lights may not have DT or ATP connections on them, but the connectors can be added from the harness kit or purchased separately (ATP-FPT).

4. Continue to route the switch portion of the harness to the desired location of the switch. The switch may need to be unplugged from the harness to make routing of the harness easier. An optional remote-controlled switch (RS-x) are also available with different legends.

5. Connect the black (ground) wire with the large ring terminal from the harness to the negative battery terminal. Connect the red (power) wire with the large ring terminal from the harness to the positive battery terminal.

6. Secure the relay to a suitable location, and test the light to make sure the circuit works.

7. Finally, aim the light in the desired direction, and tighten all mounting hardware.

3. Connect the black ground wire of the new light to the ground wire of the old light with solder and heat shrink tubing (PSC-x). Connect the red power wire of the new light to the power wire of the old light.

4. If the new LED work light or off-road light bar has an ATP or DT connector that you wish to utilize, corresponding ATP (DT-MPT) pigtails are available.

5. Finally, aim the lights in the proper direction, and tighten all mounting hardware.

1. Find a suitable mounting location that will allow for running wires and mounting the LED light bar. Mark where your holes will be for the light bar brackets or mounting feet. Check behind drilling locations to ensure nothing will be damaged. Drill appropriate-sized holes.

2. Mount the lights with the provided hardware or with DT-MPT or RRS-SP, RRS-SPx, or RCS-RF25A) under your hood to speed up install time and avoid routing wires through your vehicle’s firewall. Route another run of red wire from the pigtail adapter (connected to the light) to the output terminal of the switch. Be sure to avoid heat sources and any moving parts while running your wires. Prolonged chafing of the wires may lead to a short in the circuit. Typically, following the vehicle manufacturer’s wire harness is a safe path to follow.

4. Be sure to double-check for all obstructions and proper clearance. Drill an appropriate sized hole for the switch, and mount it.

5. Connect your black wire to the negative battery terminal. Connect your red wire to the switch input terminal and to the positive battery terminal with an appropriate-sized fuse holder (MAF-x) installed within 18 inches of the battery. You will have to cut your section of red wire to allow for the fuse holder to be installed between the switch and battery. Connect your other run of red wire to the switch output terminal.

6. Finally, aim the lights in the proper direction and tighten all mounting hardware.

Fuses and circuit breakers are part of any home or business that has electricity. These devices are extremely important to your safety, but what exactly are they?

It can be easy to take the technology around us for granted, and that includes the collection of strange switches in that metal box in the basement you never mess around with. You might have heard something about a “tripped circuit” or a “blown fuse,” possibly around the time the air conditioner shut off when someone plugged in a new appliance. But you might not be clear on what exactly these terms mean. Read on as we uncover the mysteries surrounding fuses and circuit breakers.

Circuit breakers and fuses (which can sometimes be found instead of breakers) are safety mechanisms put in place to ensure you don’t exceed certain current limits. If the wiring in a building has too much electrical current moving through it, these devices stop the flow of electricity until you address the problem.

Doing your own yard work is a rewarding experience. While there is always the option of hiring a landscape company to take care of your lawn needs, it is often a job many homeowners would like to take on themselves. It is an excellent way to get some exercise while working with your hands. One of the biggest motivators to taking care of your own yard work is the cost savings. The money you save by taking care of your own landscaping needs gives you more money to put back into the landscaping. Landscaping is not complete without adequate lighting. Although you may want to do all the work yourself, landscape lighting is one job you will want to hire a Glendale electrician to take care of. The team at The Electric Connection is here to help you.

Many homeowners who tackle their landscaping needs on their own will usually opt to install solar lights. These lights are quick and easy to install and require very little effort. They can be placed anywhere in the landscaping, but that doesn’t necessarily mean they will work effectively. Solar lights need at least 8 hours of sunlight to recharge. If the lights are placed under trees or thick shrubs that get very little sun, the solar lights will not recharge and will not light up when darkness falls.

Electric landscape lights require a little more effort to install, but they will remain lit throughout the night whether the sun shone on the lights or not. Because the lights will require electrical wire, you will want to hire an electrician. Glendale residents will appreciate the reliability of electric landscaping lights. Your electrician will wire the lights into the home’s electric panel. You can opt to have a timer installed for the lights or a manual switch for you to control when the lights are turned off and on. Give The Electric Connection a call today and schedule your landscape lighting installation.