You have probably turned on your furnace already this year or pulled out the space heaters to help warm up your room. It won’t be long before you start to see your electric bill rise with the cost of heating your home. There are some things you can do to help keep your electric bill down and more money in your pocket. Your neighborhood electrician has some best practices to help you reduce the amount of electricity you use on a daily basis. For more information, call The Electric Connection.

1-Turn the thermostat down a couple of degrees. You can wear a warm sweater or some thick socks while you are at home. At night, turn the thermostat down a couple more degrees since you will be sleeping with blankets.

2-Unplug your cell phone charger as well as tablet and laptop chargers when you are not using them. It may seem small, but every charger pulls a little electricity even when nothing is plugged in.

3-Switch out your old incandescent bulbs with CFL or LEDs. You may need to change out your light fixture, which your electrician can do for you. The investment in a new fixture will pay for itself when you save money on your monthly lighting bill.

4-Turn down the temperature on your water heater a few degrees. It is unlikely you would use water that is 125 to 140 degrees anyways. If you can’t use water that hot, it doesn’t make sense to waste the electricity heating it to that point.

5-Make it a rule you only wash full loads of dishes in the dishwasher and only full loads in the washer. Try washing clothes with cold water when possible.

6-Invest in heavy curtains to block the chilly air coming in through the glass in the winter and block the heat of the sun in the summer. This will keep your home more comfortable and save you money on your electric bill.

If you have any more questions for your electrician about energy savings, give The Electric Connection a call today to see what else you can do to save some cash.

— Electric Connection (@LAElectricianCA) December 15, 2015

When a fire breaks-out, most people just assume that it’s been caused by some inflammable substance. While that might be the case, it’s important to keep in mind that fires can also be caused by electricity. The one thing to keep in mind is that an electrical fire can’t be doused by water. Faulty or old electrical installations can lead to a fire and cause untold damage to life and property.

There are times when the electrical equipment or appliances in an electrical system can be the cause of overheating & overload, which can end up causing a fire. So, exactly what is it that causes an electrical fire? There are three main reasons, let’s take a detailed look at what these are and what can be done to prevent this from occurring:

Some properties have wiring that is decades old and electrical wires do tend to deteriorate with age. In fact, if the wiring in your house is over 15 years old, the recommendation is that you should get the entire property rewired. Older wiring wasn’t designed to bear the electricity load that current-day appliances demand. At times the electrical contractor might have cut corners and installed wiring of poor quality and this can lead to a similar problem, both of which can result in fires.

Arcing is quite a common problem with electrical wiring. As mentioned earlier, most homes have a range of heavy-duty electrical appliances. When you run a number of these appliances simultaneously in your home, it results in overloading and overheating of the wires. If the wiring is old, it will get heated up which will cause the insulation around it to melt – this results in arcing and an electrical fire may erupt too.

There are times when electrical wires are just too close to an external heat source which causes the outer insulating sheath of the wiring to melt. If this goes unnoticed, it can result in an arcing and fire.

Regardless of what has caused the electrical fire, if you attempt to contain it by pouring water on it that will escalate the issue. Water doesn’t have any effect on electrical fires; in fact, if you try to use water to douse an electrical fire, you can get electrocuted. What you need to deal with an electrical fire is a Class C fire extinguisher.

This type of extinguisher has dry chemicals that help contain the fire. Depending on how severe the fire is, it might be possible to completely bring it under control using a Class C fire extinguisher. If you don’t have this extinguisher, baking soda might help to some extent.

In case there is a break-out of fire on your property, the first thing you should do is switch off the power-mains; this is effective in containing the fire. Ideally every home and commercial establishment should have a Class C fire extinguisher or two, based on the size of the property and that should be used in case of any fire in the electrical wiring. An electrical fire is an electrical emergency and it’s crucial that you keep the number of a local, reliable electrician handy.

Never try to fix any electrical issues on your own. That can only lead to more complications and will compromise the safety of your property. We at Allround Electrical can rectify all types of electrical faults and we provide a range of electrical services. For more information, contact our friendly team today at this number – 1300 169 263. You can also write to us at this email address. You may also reach us through this online contact form.

Thanks for reading,1300 169 263

2017 is here, technology is improving, and we’ve decided to put together of our 4 best warehouse lighting fixtures that we have here on MyLEDLightingGuide. This is not a comparative list, but rather a list of our best lighting technologies for warehouses that is up to date and current for the year 2017.

Although all the lights on this list might not apply to you, surely there will be a few on this list that apply to your needs (e.g warehouse aisle lighting). As we go through the list, keep in mind that these are all currently available and can be inquired about by

In warehouses, replacing old and outdated fixtures entirely can be a pain. Our easy to install LED high bay retrofits make it easy to replace metal halide warehouse bulbs with LED without the costs or hassle that comes with an entire fixture replacement. This is a highly popular option when warehouses look to LED to bring savings in their warehouse or factory.

Since there are so many options of these fixtures,

Maybe you are in need of entirely new fixtures, not just a retrofit kit. Our extensive listings of LED high bay fixtures gives you a great option to fully replace existing fixtures or even an entire lighting redesign.

If you are in an industry which requires explosion proof lighting, our high and low powered options are great to fit in warehouses (factories more often). You have the required explosion proof light that you need with the benefits of LED technology which is going to save you money. learn more about LED warehouse lighting options here.