video in which Kathleen Packard, their Healthcare Market Development Manager, discusses how some innovations in lighting can positively affect the healing process (and save energy and money). Packard describes hospitals as being historically “institutional and very uncomfortable,” and her mission is to educate the public on the “importance of design” to patient health.

intrinsically photosensitive retinal ganglion cell in the human eye, which senses light and regulates the body’s systems, including melatonin levels, which are directly related to sleep. Visa’s Amber Night Light, she says, creates ambient light that won’t disturb the intrinsically photosensitive retinal ganglion cell. This allows nurses to check on patients without disturbing their sleep.

Of course, all this valuable information leads us to the problems solved by Visa Lighting’s healthcare light fixtures. Packard calls special attention to the benefits of using LED fixtures. She reminds us that LEDs are indeed a great option for hospitals because they are energy efficient and therefore save money, reducing the cost of healthcare; they render color well, which is necessary, so that doctors and nurses can accurately assess skin pallor; and, unlike fluorescent lamps, LEDs contain no mercury.

Regardless of bends, twists, or turns, Example of a cut line on LED strip lights

2. You will now have two LED strip lights. Carefully peel back the end portion of the paper strip covering the strip’s adhesive backing, and then remove the 3M VHB adhesive from the solder pads on the bottom side of one of the strips. The strip with its adhesive peeled back will be the top strip when soldered.

5. Align the non-tinned strip segment (strip with adhesive removed) directly over the newly tinned pads, and apply heat. Hold the soldering iron in place until the solder remelts and begins to flow. To strengthen the bond and improve visual appeal, a small portion of solder can be added to the top pad.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split and solder a run of non-weatherproof two-conductor or connecting wires. Peel away the blue wire so that only the positive (red), negative (black), and control (green) wires are left.

*No wires should be peeled away if you’re joining single-color or standard RGB light strips.

3. Properly heat your soldering iron. For best results, clean and tin the tip of the iron immediately before soldering. To tin the iron, touch solder to both sides of the iron’s tip.

4. Next you will need to tin the solder pads on both ends of the split strip light. When soldering, always apply heat to the target area on the strip and not directly to the solder. Once sufficient heat has been applied to the area, start introducing solder.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split, solder, and reseal a

3. Follow steps two through five located at the top of this post for soldering a standard RGB strip light.

4. To reseal the strip light, apply

The LED strip lights are now connected, and power should flow through the entire length of the weatherproof strip.

By Elisa Voland

So, you’ve realized you need a whole house surge protector installed in your home. Don’t panic – the entire process is a lot less stressful than you think it might be. Mr. Electric will be there to assist and make sure your expensive and sensitive electronics are well protected. We have included some information about the installation process to make this as simple as possible.

Before Mr. Electric arrives, be sure to clear at least three feet around your electrical panel as required by code for proper workspace for the technician. Don't fret about preparing your home beyond that – we understand you have busy schedules, and our experts will be able to take care of the rest. The area where we will be working varies depending on the job, but technicians will mostly be at the main electrical panel. We will be sure to use drop cloths and wear booties wherever we go in your home to prevent any dirt coming inside.

Our technicians will be sure to explain the task performed before beginning work and will answer any questions during the installation. The entire installation process should take under an hour so expect your electricity to be shut off for the duration of the time while we work.

After we install your surge protector, we will properly clean up any messes made during the job, beyond the extra precautions taken with the booties and drop cloths. We will also vacuum any debris created during our work. Mr. Electric warrants all of our work for a year, so if any problem arises with your surge protector, we will not hesitate to assess the problem and find a solution. 

After that, sit back, relax and enjoy the peace of mind knowing that your home electronics are protected when storm season arrives. We’re here to power your tomorrow! Call Mr. Electric today!