Smoke alarms have been required in homes, apartment buildings, and offices for many years. Regulations on carbon monoxide detectors are far more recent, but it’s vital to know whether a potential carbon monoxide leak could make your family members sick. The people at Nest, the same company that brought us the Nest Learning Thermostat, recognized a need for a combination smoke detector and CO detector and created a product that alerts you to danger in a unique way that helps you to feel that your home is protected no matter where you are.

We’ll look at the many benefits of integrated fire alarms and CO detectors in this guide, but be sure to call on a professional for installation. At FB Electrical Services, we’ll make sure that the unit is installed in the most accurate location for smoke and CO detection, that all of the electrical components are working properly, and that the detectors in each room are interconnected.

Regardless of bends, twists, or turns, Example of a cut line on LED strip lights

2. You will now have two LED strip lights. Carefully peel back the end portion of the paper strip covering the strip’s adhesive backing, and then remove the 3M VHB adhesive from the solder pads on the bottom side of one of the strips. The strip with its adhesive peeled back will be the top strip when soldered.

5. Align the non-tinned strip segment (strip with adhesive removed) directly over the newly tinned pads, and apply heat. Hold the soldering iron in place until the solder remelts and begins to flow. To strengthen the bond and improve visual appeal, a small portion of solder can be added to the top pad.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split and solder a run of non-weatherproof two-conductor or connecting wires. Peel away the blue wire so that only the positive (red), negative (black), and control (green) wires are left.

*No wires should be peeled away if you’re joining single-color or standard RGB light strips.

3. Properly heat your soldering iron. For best results, clean and tin the tip of the iron immediately before soldering. To tin the iron, touch solder to both sides of the iron’s tip.

4. Next you will need to tin the solder pads on both ends of the split strip light. When soldering, always apply heat to the target area on the strip and not directly to the solder. Once sufficient heat has been applied to the area, start introducing solder.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split, solder, and reseal a

3. Follow steps two through five located at the top of this post for soldering a standard RGB strip light.

4. To reseal the strip light, apply

The LED strip lights are now connected, and power should flow through the entire length of the weatherproof strip.

The commercial electricity for HVAC systems accounts for about 50 percent of a building’s total energy consumption. Being one of the major energy costs in a manufacturing facility, it dominates the building’s peak electricity demand. As such, improving the system’s efficiency, in order to cut energy costs, should be every facility manager’s priority.

The energy consumption depends on the climate, comfort preferences, building design, insulation, the timing of use, the size of the HVAC system, heat generated by electrical equipment, and other site-specific factors.

Building owners and businesses can reduce their energy costs by combining several measures that increase an HVAC system’s efficiency while reducing the demand for heating and cooling.

When selecting HVAC systems, pay attention to its design and controls. Components such as motors can impact heavily on the running costs of equipment because some are usually oversized to meet peak demands. An ideal system should have more variable speed control, inverter controls, economizers, demand controlled ventilation, advanced sensors and monitoring, as well as superior diagnostics. In addition, the system should be the appropriate size; not too small or oversized.

By controlling and running the HVAC motors at speeds based on the heating or cooling needs, consumers are able to realize energy savings of between 30 and 50 percent compared to the conventional constant speed operations. Most manufacturers prefer newer algorithm-driven smart microprocessors.

These provide a refined speed control that responds to the changing load in the building. Instead of using on and off cycling, these controls adjust the system according to the actual cooling or heating needs of the facility. More functions can be added through software add-ons as opposed to costly hardware upgrades.

Some of the ways to optimize HVAC systems include the use of thermostats and control systems, locating the HVAC unit in the best place possible, and modifying the ventilation and distribution. These are discussed more fully below:

A HVAC energy audit helps in identifying the operational deficiencies, hence allowing the building manager to take the necessary measures to enhance performance. The audit is often necessary because it helps in determining the amount of energy use, maintenance and upgrade requirements.

Consumers can then reduce their energy costs by optimizing, replacing or retrofitting the HVAC system to become more energy efficient. This not only increases efficiency and reduces the amount of commercial electricity for the HVAC system, but also improves the air quality.