Why do breakers trip? Have you ever turned on the vacuum or started the microwave while the toaster was in operation and experienced a tripped breaker? If you have ever dealt with a breaker that trips, you are probably wondering why it happened and want to know what that means for the safety of your home. An electrician in Pasadena is here to explain. You can learn more by calling The Electric Connection.

First of all, it is important to explain what a tripped breaker really is. Your breaker panel is probably located outside or in a hallway or basement area. When a breaker trips, it cuts off all flow of electricity to the outlets and light fixtures that the particular breaker supplies electricity to. When looking at the breaker panel, the tripped breaker will be slightly in the middle instead of all the way left or right. An orange bar is usually used to indicate which breaker has tripped.

As far as why the breaker trips, there are 3 main reasons • Short Circuit

An overloaded circuit is probably one of the most common reasons. If your breaker isn’t powerful enough to run several appliances at once, like the microwave, vacuum and toaster, it becomes overloaded and shuts down. You can address this by distributing your electrical draw to different outlets that are run by different breakers or by having your Pasadena electrical system investigated. You may be in need of additional breakers. A ground fault or short circuit are much more dangerous than an overloaded circuit. Breakers that have bare wires or a bad connection can cause fires. If you don’t see anything out of the ordinary, but are still having trouble with a tripping breaker, give the folks at The Electric Connection a call.

The type of in-wall wiring and cables you choose for your home will largely depend on what kind of signal you need to carry, where you’re going to route the wire, and how far the signal will have to travel between your various peripherals. Whatever type of wiring you choose to go with, you want to be sure you get one that’s rated for in-wall use by the Underwriters Laboratory (UL). This is usually going to be indicated with a CL2 or CL3 rating when it comes to speaker wire and audio/video cables. A good number of Ethernet cables are rated for in-wall use as well, usually indicated with a CM, CMR, or CMP rating. When choosing the right rating for each specific type of wiring, the UL looks at a range of different factors, including the heat being generated from current flowing through the wire, how quickly the cable will catch and spread fire when exposed to flame, and the wire’s vulnerability to damage from external stresses.

It is also important to look for a cable that’s rated for your specific needs. For instance, you are going to want cable that is rated as CL2P or CL3P if you are planning to run it in your heating ducts, or if you are looking to run your cable underground to connect to your outdoor speakers, you will want to make sure your cable is rated for direct burial. It should also be noted that when you are making the decision of what custom wiring you will need for your home, you need to be aware of your local fire codes and make your selections accordingly.

When you are looking for the right type of speaker wire for your home, there are two things you need to factor into your decision: the gauge and number of conductors. The gauge of wiring you choose should depend on how far the wire is going to have to travel from the receiver to the speaker. Significant power loss can occur over long runs of wiring, reducing your system’s performance. This might not be a significant issue in a single-room setup, but it is something to keep in mind if you are looking at a multi-room system. In terms of conductors, speaker cable comes with two or four. Two should be all you need for wiring a single speaker, but if you are looking at doing a multi-room setup, or a system with volume controls, you will mostly likely want four.

No home wiring setup would be complete without a solid Ethernet setup, but knowing which type of wiring to use can be a little confusing. When you are looking to create a wired computer network in your home, or carrying audio/video and control signals all across the home, CAT-5 cables have been the standard for a long time, but a better option these days might be to look at CAT-5e or CAT-6 cables. These newer cables are able to pass more data along the wire at a much faster rate than the older wires. The CAT-5e and CAT-6 wiring options are also backwards compatible with devices that were designed to work with the older CAT-5 wiring, meaning you won’t have to buy all new equipment. Ethernet cabling actually stands up to interference better than almost all audio/visual cables, which is a large reason it has become so popular in recent years for whole-house audio/video systems. It can also be a more cost-effective option to run long lengths of Ethernet cabling than it can be to run the same length in audio/video cable.

Home rewiring is a topic that many people are not familiar with. Besides the value of correcting any electrical safety issues, a new electrical rewire has many other advantages to offer. For example, having upgraded wiring can determine when and how you can use your electrical outlets, if you can accommodate air conditioning, and/or if your home or business can handle the load of today’s heavy duty appliances, multiple computers and more.

Here are some good indicators that a home rewire is in order from a Glendale electrician:

Instead of worrying over the state of your home or business electrical system, why not have an electrician Glendale residents recommend take a look at your home? After all, your home is much more likely to maintain its value over time if it meets both legal and common use electrical standards. Since most homes or businesses today create a high electrical demand, it is a good idea to make sure you have the best and most upgraded electrical system possible.

Finding an electrical contractor with experience in complete rewiring projects is essential. The Electric Connectionhas the expertise you’ll need, and we’re standing by to help you with your rewire or any other type of electrical projects that you might have. Why take chances with your home when professional help is just a few clicks away? Visit TheElectricConnection.com to learn more about our company and our mission to provide fast, friendly service at an affordable price.

The phrase “light recipe” is a good entry point into a conversation about LED lighting as a world-changing technology. While people originally thought of LEDs as a somewhat ineffectual light source good only for small electronic displays and then as a profound energy saver, we now understand that the potential for LEDs to change the world we live in is even more staggering than the way cell phones were first imagined to merely facilitate conversation and grew to be pocket PCs used for managing our social, economic, and artistic lives.