Stay cool as a cucumber this summer without running your electric bill sky high and your finances into the ground. Summer is such a fun time of year that we all look forward to those hot days spent at the beach enjoying the warm ocean breeze. Sometimes, the heat is just too much. We all need a break. We don’t want to be warm all the time, especially when we want to relax or sleep. It is natural to turn the AC down a bit so you can cool down after a long day in the sun. unfortunately, every degree you lower the thermostat is more money you are going to be spending. An electrician in Santa Monica wants you to stay cool and comfortable, without breaking the bank. The team at The Electric Connection has been helping customers like you for years and is here to help.

There are some things you can do this summer to help stay cool without taxing the AC. Your Santa Monica electrician says these are tried and true methods.

Stay cool this summer without having to pinch too many pennies. Give The Electric Connection a call today to schedule your ceiling fan installation.

RGB LED strip lights are a great way to add a pop of color to your above-ground pool. These low-voltage LED lights can be applied to the inside rim of your pool or around your pool deck. With RGB LED strip lights, you can choose from a ton of dynamic color-changing and single-color modes with adjustable brightness and speed control. They’re great for parties or late-night swims and can be easily installed. We’ve included installation instructions for our waterproof LED strip lights. Some cities require above-ground pool lighting to meet National Electrical Code (NEC) Article 680 standards, which would limit possible pool lighting installation locations. Before you purchase LED pool lights, check your city’s code requirements. We also recommend that you have a certified electrician install your lights.

 

1) Before ordering your LED strip lights, measure the diameter of your pool and multiply by 3.14 to find its circumference; this number indicates the total length of strip that you will need. The 21-foot pool used for these installation instructions has a circumference of 65.94 feet and requires 4 runs of 16-foot LED strips.

You will also need to measure the distance between where your power supply will be and both sides of your pool where the amplifiers will be installed (see the setup and wiring illustration below). These distances will tell you how much 18-gauge wire you’ll need for connecting the amplifiers to power. Make sure to account for the distance of any dips or turns that the wires may take along their paths.

Lastly, measure the approximate distance that will be between your controller and where your strip lights begin. This distance will tell you how much 22-gauge wire you’ll need for connecting the controller to your strips. You will also need two small sections of this wire for connecting your first and second strip lights to the amplifiers.

2) Before you’re ready to install your LED strip lights, be sure to drain your pool. Begin by creating or locating a dry area away from your pool for the power supply. The power supply should be contained in a weatherproof box. Power supplies should be installed between a ground fault circuit interrupter (GFCI) protected circuit and the pool’s junction box. It’s crucial to use a GFCI protected circuit as it shuts off if current flows where it’s not supposed to.

Wire the included plug to the power supply, but do not connect to power until the installation is complete.

3) Connect your RGB LED controller to the power supply. Cut the barrel off of the controller wiring. Strip back the remaining wires, and connect its wires to the power supply.

4) Cut the LC2 connector off of the remaining end of the controller, and strip back the wires. Run 22-gauge four-conductor wire to connect the controller to your low-voltage pool lights; use dolphin connectors to join like-colored wires. Connect your first two LED strip lights to the controller by joining each set of like-colored wire with a dolphin connector. You should be connecting four wires of each color (red, blue, green, and black) together. For added protection, cover all wire connections in this installation with electrical tape.

5) You will apply strip 1 clockwise around your pool rim and strip 2 counterclockwise. If you have a flat surface, use mounting clips to secure the strips in place as you go. If you want to mount the strips under your pool rim, drill small holes in the trusses approximately every 2 feet. Use cable ties to anchor the strip to the truss. You can also use speed nuts or cotter pins for strip anchoring to avoid drilling holes.

Solder a small section of 22-gauge four-conductor wire onto the strip’s end terminals. To reseal the LED pool light strip, slide wires through the holes of a 10-mm end cap, fill the cap with silicone, and slide it into place on the end of the strip. Be sure to cover all of the exposed conductive traces to ensure water resistance. Allow a minimum of two to three hours for the sealant to cure.

7) Once the new end wires are attached to the strip, you will mount the amplifier. Use the double-sided 3M foam pad to mount the amplifier in the middle of strip 1 and strip 3. For best results and added security, apply 3M adhesion promoter to the amplifier and its installation location on the pool wall.

8) Using a dolphin connector, join each like-colored wire on strip 1 to the same color on one end of the amplifier. Do the same when connecting strip 3 to the other side of the amplifier. You should be connecting three wires in each color (red, blue, and green) together on each side of the amplifier. The black strip wire will be joined with white amplifier wire. Note that the separate group of just black and red wires are meant to be connected to the power supply. Follow the same instructions for connecting strips 2 and 4 to the amplifier on the other side of the pool.

9) Use 18-gauge wire and dolphin connectors to connect the amplifiers to your power supply.

10) Plug the power supply’s attached cord into an outlet, and enjoy your LED pool lighting system! Refill your pool with water, but make sure to leave space between the water line and the lights.

For more LED pool lighting options, see our entire selection of waterproof color-changing LED strip lights.

 

For technical questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

Electricians have been using copper for electrical wiring since the 1820s. It may surprise you to know that since then, we’ve never found, or needed, a replacement! Copper has numerous properties that make it ideal for electrical wiring. In fact, we can likely expect copper to continue to be used far into the future.

Ductile and Malleable—ductility and malleability are two very useful properties of metals. Something that is ductile can be hammered into a thin wire easily, and something malleable can be manipulated and bent into shapes easily. These properties make copper wires inexpensive to produce and easy to install.

Excellent conductivity—copper’s electrical conductivity is far superior to other types of non-precious metals, which allows it to carry greater amounts of current with a smaller diameter wire.

Non-corrosive—one of the biggest benefits of copper wiring is that it is non-corrosive, able to survive in harsh environments with almost no risk of wear and tear. It’s not uncommon to see copper wires last for 40 years or more!

All of these properties make copper the gold (or should we say copper!) standard in the electrical industry. For both commercial and domestic purposes, copper is considered the go-to material for wiring. In fact, most modern buildings being constructed today are designed to accept copper wiring. The prevalence of copper wiring makes rewiring a lot easier as well.

During the 1960s and 70s, aluminum wiring was used in many homes as a cheaper alternative to copper. Unfortunately, problems were discovered with aluminum wiring. The biggest danger associated with aluminum wiring is that it can react to materials used in outlets, light fixtures, and splices, where it can oxidize, deteriorate, overheat, and catch fire. The CPSC estimates that about 2 million homes were built with aluminum wiring between 1965 and 1973—and many of these homes are located in the MD, VA, and DC area.

The other problem with aluminum wiring is its high electrical resistance, which makes it more difficult for current to flow. As a result, you experience greater losses with aluminum wiring than you would with copper.

More than any other material, copper has stood the test of time for use in residential and commercial applications. If you’ve been thinking about rewiring your home and want to use the best materials possible, call Kolb Electric today!