Commercial buildings such as ones that house a large number of offices also consume a significant amount of electricity. Most businesses look for ways and means of saving electricity and making their premises more energy-efficient. There are numerous ways in which you can optimise energy-efficiency on your commercial premises.

For instance you can install high grade insulation, install energy-efficient windows and doors, get blinds, drapes and curtains; and use UV-resistant glass film on the window panes etc. While all of these are important aspects, it’s also very important that you incorporate some cost-saving electrical solutions for your commercial building, such as:

Most people try various energy- saving methods in an effort to reduce their utility bills, but one of the simplest ways of lowering your energy usage is to make the most of natural light. This process of allowing the sun’s rays to light up indoor spaces is referred to as daylighting. It can help reduce your buildings energy requirements, while also improving the health & productivity of your employees.

LED fixtures, such as

With energy consumption that is less than half of what 150-watt LED parking lot light that is a direct replacement for 400-watt metal-halide (MH) fixtures. That’s 250 watts less for the same amount of light!

The average price of electricity per kilowatt-hour (kWh) is 12 cents. To figure out the monthly cost of running 25 LED parking lot lights for 11 hours per day, use this formula: (combined wattage x monthly hours of use)/1,000 x price per kWh. For 25 LED lights, (3,750 x 330)/1,000 x .12) the total would be $148.50 per month or $1,782 per year.

When the same formula is used for 400-watt MH fixtures, the monthly cost is $396, and yearly cost would be $4,752. So, in this situation, switching to LED fixtures would save approximately $3,000 per year. When coupled with the savings on maintenance, LED fixtures can save $6,470 per year. At that rate, the cost of 25 $340 LED fixtures would be recouped within two years.

Left: LED wall packs; Right: HID wall packs

Unlike LED fixtures that light up instantly, HID parking lot lights require a warmup period of up to 10 minutes before they reach full brightness. They also can’t be turned immediately back on after being switched off; this is called restrike time, and it can take up to 15 minutes before they can be turned on again. Attempting to power on the lights before the bulbs have cooled can damage a fixture’s components and cause the HID bulb to fail sooner.

HID lamps consist of a ballast and a quartz tube that contains gas, metal salts, and two tungsten electrodes. In order to create light, an electric arc passes from one electrode to the other through a gas (most commonly mercury, metal halide, or sodium). The mercury used in this process is dangerous if enough is inhaled or released into the environment. If an HID bulb bursts, all contents should be put into a sealed container or sealed bag and taken to a recycling center or hazardous waste facility. If HID fixtures are used indoors, wall packs and canopy lights, are used indoors, the possibility of ultraviolet (UV) radiation exposure should be taken into consideration. HID bulbs emit a substantial amount of UV radiation, but an outer glass envelope prevents the radiation from escaping. However—according to the FDA—”If the outer bulb breaks and the inner tube continues to operate unshielded, intense UV radiation is emitted. UV exposure at this level can cause eye and skin burns, as well as blurred or double vision, headaches, and nausea.” The UV light from an HID bulb with a broken envelope can also lead to discoloration of items and fabric. LEDs emit little to no UV radiation.

In short, LED lights are a better alternative to HID parking lot lights. They offer a great deal in the way of savings, longevity, maintenance reduction, brightness, color, and safety. While it may take a short amount of time to recoup the price of switching to LEDs, all of their qualities make it easy to see why so many businesses have started the process.

For technical questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

Prisons and correctional facilities are full of security threats, it’s just common sense.

That is why it’s a major task and a seemingly forever ongoing one to try everything in the book to reduce threats and increase security for everyone in, near, or even outside the facility.

Today we wanted to address how we can solve 2 major correctional lighting system and things you should look out for when finding fixtures perfect for your building and budget.

Firstly, a LED prison lighting system will reduce indirect stress and irritability in both inmates and staff.

Secondly, LEDs within correctional buildings will improve detection of movement, which we all know is crucial.

How you ask? Well, lets talk about each one individually and break it down a bit more than just one sentence. From there, we will talk about how to go about making the conversion over to LED, like we mentioned at the start.

Have you ever been around a light that was flickering and or buzzing? It can get annoying, and fast. Imagine living under these conditions, everyday all day; no break other than a few hours when you go outside. Sounds like no fun, and it can lead to some serious stress and irritability issues for both inmates and staff.

For obvious reasons, additional stress on inmates will never produce a good outcome for anyone. But, another important point is that this can effect your staff and guards too. It can affect their ability to perform at full capacity, which in combination with highly irritable inmates is not a good mix whatsoever.

With LED technology, they will never be susceptible to flickering nor buzzing. Not even near the end of the lights lifespan will they flicker or buzz, unlike other technologies commonly still used in such facilities. Thus, you can avoid any stress or irritability which may be caused from flickering / buzzing lights.

If you can’t tell where everyone is at every second, you’ve got an issue. This is especially important for outdoors during the time when it is dark out. Sure, some light is better than none; but why jeopardize your operations with a flickering light when you could upgrade to LED and get rid of the issue entirely?

As you may or may not know, flickering lights make it harder to not only detect movement, but also identify humans. Think of a strobe light, it’s a bit harder to actually make out what is going on entirely. This holds true with a flickering light, even if it isn’t as bad as a strobe light is.

Here we are going to list a couple of the other major general benefits that LED technology offers over other technologies such as metal halide, HPS, fluorescent, and similar.

There are really only two routes you can take, LED retrofit lighting kit will work perfectly. On top of that, retrofitting is a much cheaper option (typically) then a full replacement is. So, if you don’t need to fully replace then stick with retrofit kit LEDs and you will save a lot on your lighting system investment.

Conclusion

Flaws can always be picked at, especially in such tedious and unpredictable environments like the one we are discussing in this topic.

It is that time of year when the temperatures drop and things like spiders and mice are seeking shelter in your home. You don’t want to share your living space with the critters and they know that. They will stay hidden for the most part, but that means they are somewhere you can’t see what damage they are causing. Mice will chew anything and everything and they don’t care if they get a little jolt when they bite through a wire. Chewed wires can spark and create an extremely dangerous situation in your home. An electrician in Burbank has a few tips to help you protect your home from the damage a rodent can cause. The team at The Electric Connection is on standby and ready to help you.

Rats are much worse than mice, but both are equally troublesome. They both love the heat the insulation in the walls provides and will make their nests there. These nests often encompass wires that run warm. An overheated wire is another fire hazard. The following will help keep your wires safe from gnawing rodents.

*Your Burbank electrician suggests you hire a pest control service to ensure the rodents stay out of your house. The best cure is prevention. Take action at the first sign of an infestation. If you see one, there are plenty more where that came from.

*Seal up any gaps around the foundation of the home. Mice can squeeze through a hole or crack that is a quarter of an inch thick. Steel wool is a quick and easy fix for small holes.

*Regularly check your crawlspace and attic area for signs of rodents. Use traps if you suspect you have a problem.

*Schedule an electric safety inspection with an electrician. Burbank homeowners who want to know their wiring is safe will feel better once an electrician checks for any issues.

Give The Electric Connection a call today and schedule your inspection to determine if you electrical wiring has already been compromised by a rodent infestation.