If you’re in the midst of a renovation or simply rearranging your floor plan, then you’ve likely come across the need to add or relocate a light fixture. Maybe your new dining room table is a little wider than the old one, you’re adding a kitchen island with pendant lights, or you’ve finally convinced your significant other to let you get that pool table you’ve always wanted. In any case, you need to move or add a light fixture – but how and when?

First, it should be noted that, contrary to how it may seem, most light fixtures are not connected to a joist or even drilled into wood. Instead, hanging light fixtures and ceiling lights alike are located between joists and supported by electrical boxes that grip a wide surface area of the sheetrock that makes up your ceiling to support the weight of the fixture below; for heavier fixtures, like large chandeliers or ceiling fans, there are larger, even joist-secured boxes that will need to be used.

If you’re moving a light fixture, it is important to note that there are certain limitations as to where the fixture itself can go. If you wish to relocate the fixture to a place where a joist exists just above, then you’re likely going to have to use a swag hook and chain to anchor the fixture in place, as a box under a joist is not an option. That said, if you’re moving the housing for the fixture itself, you’ll need to know which direction the joists above run, then choose to move it either through the same joist cavity or drill through a joist to run the current wiring to the new housing. Other things to consider include which switch controls the light and where it is located, as it is a safe bet that a wire will have already crossed all joists above (at some point). This can prevent your electrician from drilling needlessly by allowing them to fish the wire back to the earlier point. If your switch is further away than the destination, you can bet they’ll have to do some drilling. Jumping through, between, and around the joists in the ceiling represents the largest obstacle your electrician (and light fixture) will face.

Once your location is set, all that is left is to get your electrician out to assess and perform the work for moving your box. If you’re planning on doing one large fixture over a pool table, island, or entire room, then you’ll want to take into account the power output of the fixture compared to what that circuit can safely allow for as well as the weight of the fixture. A typical rule of thumb is that anything under about 35 pounds can be handled by a standard drywall box, but something more (or with a fan) will need extra stabilization. Surprisingly, if you’re running numerous small pendant lights, the electrician may have an even easier time running the circuit and ensuring that your lights are up and running in no time. Just be sure to discuss the fixtures you have in mind with your electrician before you purchase them to know what they believe your limitations are!

Whenever you need electrical work done around your Des Moines home, contact the experienced professionals at Electrical Gurus. We are proud to offer the finest licensed local electricians in the area and are always more than happy to help out on your household projects.

You Can Be Liable for Unlicensed Electrical Work

07/30/15

Revamping your home's electrical work can be a big headache. You need to find a qualified electrician and write what could be a hefty check for work that might require opening holes in your walls and temporarily making a mess of your home. The last thing you want after a big electrical project is to have to tear it all out and redo the job all over again. That could be the scenario you face, however, if you cut corners and don't hire a licensed electrician to take on the task. Fly-by-night contractors might be cheaper at the outset, but they can cost you big time in the end if they don't follow the local building code, leaving you liable for the faults in your home wiring.

Fanning the Building Code Fires

Some contractors might complain about having to follow local code, but it's in place for a reason – it helps ensure that any work done on your home is performed safely and effectively. Local code standards are particularly important when it comes to electrical work, because faulty wiring and connections can lead to short circuits or even an electrical fire, putting your family at risk.

That's why technicians who do electrical work are required to maintain a license, secure permits and schedule inspections for many home projects. Unfortunately, there are electricians who are tempted to skip the code requirements in order to avoid the time and expense of compliance. They might quote you a lower price, but shoddy workmanship can leave you on the hook for a lot more money overall.

Limit Your Exposure to Liability

If your local government figures out that you are working on an electrical project, they can send an inspector to check it out. If the work isn't up to code, you'll have to remedy the problem before you pass inspection. And if your electrician isn't licensed, you have little recourse to correct the faulty electrical work besides paying out of pocket for someone else to redo the entire thing. Worse, if your electrical system does cause a fire that leads to injury or death, you could be civilly liable for huge sums.

Licensed electricians, on the other hand, have more incentive to follow the rules to begin with, since they could lose their certification if they don't. Furthermore, you may have an easier time recouping your investment in the event of unsafe or incomplete work if you can prove that you did your due diligence and hired a licensed electrician.

Good Work Done Right

To avoid code and permitting issues, hire only licensed technicians for your electrical work and ask them to show you all the relevant permits. Protect yourself and your home by holding out for competent contractors so you know the work is done right the first time.

The most dangerous time of the year for electrical fires in Des Moines is undoubtedly during the holiday season. Christmas decorations, in particular, lead to a dizzying amount of house fires each year. On average, over 200 homes burn down each year directly because of Christmas Trees and other decorations, and this figure doesn’t include the small, contained fires and those caused by candles. Needless to say, safety should be a major priority when planning out and putting up your holiday decorations.

Many electrical problems are caused by outdated technology and old incandescent Christmas lights; when you start digging out your decorations, ask yourself if it is time for an upgrade. While more expensive, modern LED Christmas lights use far less power, generate less heat, almost never require bulb replacements, and last far longer than their incandescent ancestors and inexpensive alternatives. In terms of cost alone, the new lights will likely pay for themselves in energy savings after only one, maybe two, holiday season(s).

For instance, running 1,000 incandescent Christmas lights for a month in Iowa will likely cost about $122, whereas the same amount in LED bulbs (which shine brighter, by the way) will cost less than $1.50. That extra $120 can go a long way towards buying a few better presents or do some real good in the community. By upgrading your lights this holiday season, you’re ensuring that you don’t have to hike up your energy bill to decorate the house each year while keeping the family much safer than they would be with your old lights.

For any strand you choose to not upgrade this year, be sure to thoroughly check each strand for frayed wires or cracked bulbs. Incandescent bulbs can easily create a completed electrical circuit with a Christmas Tree, gutter, or just about anything else it may be hung upon, creating a very real fire hazard.

If you decide to get out the extra-tall ladder that you seem to only use to decorate and un-decorate the house each year, take special care to avoid power lines. One of the easiest ways to get injured when using a tall ladder isn’t actually from falling, but from electrocution while moving the ladder. Take the time to locate all power lines before beginning work and always get down and collapse the ladder before moving anywhere around power lines.

No carpeting, drapes, curtains, or other fabrics should ever come into contact with your lights. Furthermore, be sure to never wrap cloth-like decorations around your lights. The mesh commonly found at holiday stores is made for wreathing and often contains metallic elements for a shimmering effect, making it especially potent at conducting electricity and starting fires in the event of a short.

We hope you’re safe this holiday season, but if you happen to overload your circuit breakers or have a concern about the lighting of your holiday decorations, be sure to give us a call right away. The electricians at Electrical Gurus want to help to keep every Des Moines family happy and healthy throughout the holiday season.

solar lights to our online store, and there are a handful that I’ve been ogling since the day they took residence on our site. In a strictly professional quest to gain a better understanding of our product offerings (wink, wink) I requested some products for thorough evaluation. The first item to take the spotlight: The Solar LED White Washed Metal Lantern:

The Nitty Gritty:

This lantern would be an attractive addition to just about any style or decor. Use it with a beachy/coastal home or a rustic mountain cabin. I probably wouldn’t choose it as a decoration for an ultra-modern home, as it has a very vintage look.