The electrical system in your home is its most vital component, more so than its gas and plumbing. Without electricity, most basic tasks during the day are impossible—and they become worse than impossible at night. If you have an electrical system that is suffering from repair needs, you can’t wait for a full power loss before calling for repairs. Watch for the warning indicators listed below that will tell you to contact a licensed and experienced electrician immediately.

Call us for these services or for electrical system repairs in Mill Creek, WA.

If you’ve ever watched the show “Holmes on Homes” on HGTV, you’ve likely seen the problems associated with old or faulty wiring.  Mike Holmes tends to get very agitated by safety issues, and for good reason.  Each year, over 40,000 homes suffer fire damage due to home electrical problems.  These electrical fires account for hundreds of deaths and thousands of injuries.  And what’s the main culprit?  Old wiring!

If you live in a classic home built before 1940, chances are you have old wiring in the house.  You may have knob-and-tube or Romex wiring, both of which can become brittle over time.  The insulation dries out and starts to crumble, causing the inner wire to become exposed. The cloth insulation around the wire deteriorates with age and eventually becomes unsafe.

But perhaps one of the biggest threats of Romex and knob-and-tube wiring is that these types of wires aren’t grounded.  That means if one of your appliances shorts out, you could become the path to the ground for the electricity.

Even if your home is only 20 or 30 years old, you could still experience electrical problems at home due to a lack of capacity.  Most homes built more than 10 years ago are not designed to handle the amount of electronics we use today.  Think about it:  if your house was built in 1980, it was built before home PCs and laptops and HDTVs and surround sound and all of the other toys and gadgets we use today.  These appliances can draw a lot of power, and your current electrical wiring may not be up to the task.

If you own one of the one million houses in the DFW area that’s more than 20 years old, it’s a good idea to have a licensed electrician come out and take a look at the wiring.  He or she can make sure that your house will be safe and productive for many years.

We had a call today from a customer. They were looking to retrofit their existing fixtures with LED. The competitor did a quote for them, and had recommended LED Post Tops as the retrofit bulb of choice for them. And this would have been a terrific solution if all their fixtures were acorn style pole mounted lights. But they weren’t, they were high bays, parking lot lights and show room lights. Yes. They are LED. Yes. They will save you money. But if you are trying to plow a field, you don’t buy a Porsche. You buy a tractor. The right vehicle for the job. And the same applies to LED.

First, let’s make sure we set the score right. We sell both. We sell LED Post Tops and we sell LED Retrofit Kits. We are not Post Top biased or Retrofit Kit biased. We even sell new fixtures. We have no biases! We want what is right for you!

contact our team and we’ll get back to you.

If you live in the United States, you’re likely well-familiar with our typical wall-socket setup. Your plug has two flat pieces of metal roughly half of an inch wide, with one side sometimes being slightly wider than the other. Your wall socket has two slots that match this, with one side also being slightly larger than the other. However, sometimes there’s a variance: some plugs have a third prong below and between the normal two, and most electrical sockets also have a third hole to match this plug. What’s the difference between these two types of plugs and is one better than the other?

To put it simply, yes, one is better than the other. When it comes to electrical plugs, the old adage “less is more” does not apply—the three-prong plug is far better than a two-prong. To learn why, let’s discuss the difference between the two.

In order for electricity to flow, you must complete a circuit. A circuit essentially is a connection from your power source to the device, and then from the device back to the power source. The line that brings power from the power source to the device is called your “hot wire”, which is most often red and comes off the positive terminal (noted by the large “+” sign). The line that then returns from the device to the terminal, usually a black wire connected to a “-“ sign, is known as the “neutral wire.” A plug must have both of these lines in order to work.

However, the third prong in a three-prong plug is a “ground” plug, which dramatically improves safety. When an unexpected burst of electricity happens, such a short in the device or a surge from your power supply, the ground plug will take that abundance of additional electricity and move it away from the device and down into the ground where it is safe. This prevents your device from being overloaded which can cause overheating, sparking, and fires in addition to ruining it.

Three-prong plugs didn’t become the standard in homes in North America until the late 1960s. If you have a home that was constructed around this time or after, odds are your wall sockets are probably already of the three-prong variety. Two-prong plugs can work with three-prong sockets just fine, and you’ll rarely experience any issues.

However, if you have any old two-prong plugs, you’ll likely need your electrical system updated in order to upgrade to a three-prong setup. Properly installing ground wires can involve several hours of electrical work and even cutting into your walls in order to do so properly, so it’s a rather large undertaking. However, it’s by far the safest and most prudent option.

Another option that doesn’t involve tearing open your walls is to install a ground fault circuit interrupter outlet, otherwise known as a GFCI. These sockets are two-pronged, but feature a miniature circuit breaker that measures the resistance through a plug and mechanically shuts off when the risk of a shock is present. While this can help you avoid being shocked by a faulty device, there is still no ground wire present so your electronics are not protected from a power surge.