One of the questions we’re frequently asked is, “How do I know if I have to replace a light switch in Fairfax, VA?” And that’s a very good question, because most of us don’t think twice about flipping a switch on or off. However, it’s critical that you make sure your light switches are in good working order, because not doing so is likely to end in injury, especially because flipping a switch is an automatic action.

Just think about it: you come home in the dark, and the first thing you do is switch on the light. Or if you wake up in the middle of the night and need to go to the bathroom. That’s three light switches you have to navigate while being barely awake (the one in your bedroom; in the hallway; and in the bathroom). Same thing if you enter your garage on a winter morning: you’re focused on getting in your car and getting to work safely—not on the possibility of getting an electric shock from a faulty light switch.

Signs You Need to Replace a Light Switch in Fairfax, VA

So how can you tell if your light switch needs replacing? Pay attention to the following signs:

If you notice any of these signs, it’s time to call us! The sooner you call, the better, because a faulty light switch can cause electrical shocks (which can in the worst case be fatal!) and electrical fires that can destroy your home and injure your family or worse—cost them their lives. So be responsible, and call Beacon right away!

It’s hard to imagine life without electricity. Those rare times when the power goes out entirely serve as reminders of how much we depend on our electrical systems to get us through the day (and night). You need to take special care of the electricity in your home with prompt repairs whenever they are needed.

Gas prices are fabulous—right now. We all know it is only a matter of time before the gas prices creep back up and we will once again be forced to pull from other areas of our monthly budget to afford to drive our vehicles. Many people have already made the switch to electric cars in an attempt to save money on their gas bills while reducing the strain on natural resources. There are plenty of different models of electric cars available that are sure to suit your needs. When you make an electric car purchase, you will likely also buy a charging station for you car. An electrician in Pasadena has some vital information for you. The team at The Electric Connection can also help answer questions about the electrical requirements of your electric car charging station.

When you buy your car, you will have the choice to buy a Level I or a Level II charging station. A Level I station is essentially a trickle charger. It sends a small charge to your car and can take upwards of 24 hours to fully charge the car. This charging station can be plugged into a standard outlet. However, it will need to be the only item plugged into that outlet and should be on its own breaker. If you need additional outlets or breakers, your electrician can take care of that for you.

A Level II charger is a fast charging system that typically fully charges a car in about 8 hours. This charging station requires a 240-volt outlet, which is not standard in your garage. It is a special outlet that will require installation by an electrician experienced with Pasadena electrical requirements. An inspection of your breaker panel will need to be conducted to make sure you have room for an additional breaker dedicated to your fast charging station. These are all things your electrician will evaluate on the first call. Give The Electric Connection a call today and schedule your consultation.

If you are renovating or updating your kitchen, one common kitchen addition you might be interested is a garbage disposal unit. This little unit sits in your sink and allows you to shred food that you would not normally fit down the drain. This can be a handy appliance, however it may introduce the threat of electrocution into the environment, as water and electricity don’t mix well. If you are looking at having a garbage disposal unit installed in your sink, have one installed safely.

The garbage disposal unit is installed into your existing sink pipe. In order to power the unit, you will require a 120-volt GCFI (ground-fault circuit interrupter). This means that you will need an outlet under your sink to plugin into. If one is not available you will need to have it installed. Often, other appliances may already heavily load kitchen circuits, it is important to check the load on that circuit before installing a new electrical outlet. If you are not careful, every time you run your garbage disposal you could cause the breaker to trip and lose power to your toaster, microwave, or refrigerator.

At times disposal units may need maintenance, become clogged, or break down for some other reason. To identify the problem you may need to open up the sink or motor to get to the part that you need access to. Before you begin any work, shut down the circuit that the garbage disposal is on and unplug the unit. This will not only keep your fingers safe from the motor activating unexpectedly, but it will also help you avoid an electrical related accident. If you start to take apart the pipes and water begins leaking there is a big risk of electrical shock. If you are not familiar with the plumbing or electrical work of the garbage disposal, leave it to a professional. You may think it is a simple job, but one mistake can be costly.

Before having a new garbage disposal installed, inspect your sink and pipes for any leaks. If these leaks make contact with exposed electrical wires or outlets there is risk of electrical shock. If you are not familiar with the plumbing or electrical work involved in installing a garbage disposal unit, call an expert. Our licenced electricians can ensure that your kitchen circuit can handle the unit and install a new electrical outlet.