Demand for the electric cars has been on upward trend over the last few years. However, manufacturers and car owners still face a challenge due to the limited battery capacity which necessitates the need to keep on recharging after traveling a certain distance.

Despite the benefits of charging the electric cars at home, most residential installations, especially the older ones, may not support the systems. But the consumers can upgrade these to accommodate the additional load. The upgrade depends on the existing wiring, panel, capacity and charging station power requirements.

electrical wiring and capacity, and the charger voltage and level. The electric car owner must first decide on the preferred type of charger and time, and then compare its power requirements with the existing capacity at home.

Some chargers require 120V while others work on 240V and each takes different times to fully charge the batteries.  Higher voltages will require dedicated circuits and upgraded wiring, breakers, panel and service entrance.

Other upgrades include the price plan, metering, and compatible outlets or provision for hard-wiring. If you are installing a DC charging is very fast; it uses about 400-volt direct current and is capable of reaching full charge in about 15 minutes. This is a complicated method and may require significant upgrades in the home electrical system. It is also very expensive and rarely used for home charging.

upgrade your wiring or install the product if you system capacity can support it.

It is essential to ensure that the electrical panel and dedicated circuit have the capacity to handle the system. The installation of the charging station is similar to other high power equipment, such as clothes dryer, and should comply with all the electrical codes and requirements.

Each charging station should be on its own dedicated circuit with adequate capacity and protection. However, the it can still be connected to an existing 40 Amp circuit, such as the one for the kitchen, provided that there is a locking mechanism to ensure that only one load is connected at a time.

Charge stations may be hardwired or plug-equipped to connect to the electrical outlet. For the plug type charger, you will need to have an electrician to wire the compatible electrical receptacle according to the codes.

You may add ventilation to improve the cooling of the charge station if it is in a location with poor air circulation.

Charging electric cars at home is the desire of the majority of EV owners. It cuts down on the cost and time to drive and wait at a public charge station. In addition, it does not interfere with the daily activities of the electric car owners since they can charge at night.

Unfortunately, there are several homes without the provision or capacity to support the charging stations. However, the EV owners can consult the car dealers, and then engage qualified electricians in upgrading the existing electrical wiring. This will enable them to conveniently charge at home.

Tube lights are found in many applications and environments such as office buildings, hallways, garages, and really anywhere that has a low and flat ceiling. Although fluorescent tubes contain small amounts of mercury and isn’t a whole lot, you still want to avoid the breaking of a fluorescent tube and any exposure to mercury if possible.

Whether you are simply replacing a burnt out fluorescent tube with a new one or are switching over to a new technology (such as LED), there is a proper way to do it. By following these steps along with others that you may find, you will allow yourself to reduce risk of harm for yourself, staff, or whoever is the one physically replacing the tube lights.

Let’s answer some common questions and issues that people seem to face when tasked with this issue of replacing mercury filled fluorescent tubes…

By recycling rather than simply throwing away your tube lights, you opt-in for the environmentally friendly route of switching out old tubes. If you choose not to recycle, you are allowing toxic mercury to freely enter the environment, which of course is not good.

Not only do you prevent mercury from freely entering the environment by recycling, but you also reduce waste. How exactly? Part of the tube is reused for new tubes that will be resold and used. This allows for less waste and this goes back to the saying “Reduce, Reused, Recycle.” So by taking part of fluorescent tube recycling, you allow the process of recycling to continue and prevent waste from entering the landfill!

When taking your tubes out to bring for recycling, this is probably the most difficult step you need to be most cautious with. The best option you have is to be prepared and know what to do if things go “south” as they like to say.

Here is what you can do to prepare for the removal of fluorescent fixtures:

And for one thing that you should always remember for dealing with a broken tube is this: NEVER VACUUM. By vacuuming, you make glass particles go airborne and that is a highly dangerous situation to be in.

For more tips on how to clean up a broken fluorescent or CFL lights, using this tool from Earth911. It allows you to search what you need to recycle and where you are located. So you go to that tool, type in ‘fluorescent’ or ‘CFL’ along with your location and you will surely come across the closest place to recycle fluorescent tubes (along with really anything else you may want to recycle).

If you are in the process of disposing and recycling your fluorescent tubes, what is going in there to replace the ones you are removing? If the answer is “more fluorescent tubes,” may we ask why?

Time to ditch the band posters! Show off a new painting or favorite framed photograph with a battery-operated picture light that installs easily and without messy cords.by Celebrate home ownership by decorating the front door or mailbox  with a customizable house number sign.

Repairs are an inevitable part of home ownership and there’s nothing quite as frustrating as not having the right tools. Cover all of their bases with a 130-piece tool set. Make small repairs and upgrades easy with a flexible work light that can clamp onto surfaces and direct light right where they need it.