CFLs are those new, small fluorescent light bulbs that screw into most regular light fixtures. You can use them to replace regular (incandescent) bulbs to save money and electricity. As the Los Angeles Department of Water and Power gets over 60% of its electricity from fossil fuels, especially coal, any time you replace a regular incandescent bulb with a CFL, it’s one small step towards reducing fossil fuel use in L.A.

CFLs come in all different shapes, but basically they’re a fluorescent tube bent this way or that or twisted into a spiral. “CFL” stands for “Compact Fluorescent Lamp.” They’re more compact than the long fluorescent tubes of our childhoods. They’re lamps, which is electrician-speak for “light bulb.” Here’s why they’re green — they save 75% of the energy that traditional incandescents use.

Here’s why they save you money — they cost more than a regular incandescent, but last a lot longer — 13 times longer. So even though each CFL costs more per bulb (about $4 for a CFL), it will also save you about $4 in bulbs as you won’t have to replace it so often.

Your electric bill will show more significant savings. Lighting costs about $20 out of $100 monthly electric bill. Because CFLs use one-quarter of the electricity of a regular incandescent, if you replace all the bulbs in your house with CFLs, you’ll save about $15 each month on a $100 electric bill.

CFLs are green, but not blue. Many people don’t enjoy the eerie bluish light of the old-fashioned long fluorescent tubes. CFLs can create all different colors of light, including warm tones. A recent study by the magazine Popular Mechanics found that even when people didn’t know which type of bulb was involved, they preferred the light of the CFL over the light from incandescent bulbs. CFLs also don’t buzz as the long tubes did.

CFLs have one downside — they each contain a small amount of mercury, which is a toxin. If a bulb breaks, you’ll need to take care to clean every bit up and to not touch the pieces. You’ll need to recycle spent bulbs or dispose of them as you would paint or other hazardous waste. However, they’re so long lasting that this will come up on the order of years, rather than months.

OK so you have a basic understanding of CFLs, now what can you do that’s simple to save money and electricity? The next time you go to the store, pick up a four-pack of CFLs. Choose four incandescent lights in your home or business that you use often and replace the incandescent bulbs with your new CFLs. You’ll start saving on your electric bill and will decrease the burning of fossil fuels to power Los Angeles.

Click here for more tips on saving electricity.

When you’re talking about electricity, safety is always one of the most important points to be made. Protecting yourself, your home, and your electrical appliances is a big part of having a functional home here in Tampa. And in our area, one of the biggest risks that can come up is a lighting storm. Lightning arresters are a great, effective way of taming these storms, and today we’d like to talk about what they are, how they work, and what they can do for you and your home!

Regardless of bends, twists, or turns, Example of a cut line on LED strip lights

2. You will now have two LED strip lights. Carefully peel back the end portion of the paper strip covering the strip’s adhesive backing, and then remove the 3M VHB adhesive from the solder pads on the bottom side of one of the strips. The strip with its adhesive peeled back will be the top strip when soldered.

5. Align the non-tinned strip segment (strip with adhesive removed) directly over the newly tinned pads, and apply heat. Hold the soldering iron in place until the solder remelts and begins to flow. To strengthen the bond and improve visual appeal, a small portion of solder can be added to the top pad.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split and solder a run of non-weatherproof two-conductor or connecting wires. Peel away the blue wire so that only the positive (red), negative (black), and control (green) wires are left.

*No wires should be peeled away if you’re joining single-color or standard RGB light strips.

3. Properly heat your soldering iron. For best results, clean and tin the tip of the iron immediately before soldering. To tin the iron, touch solder to both sides of the iron’s tip.

4. Next you will need to tin the solder pads on both ends of the split strip light. When soldering, always apply heat to the target area on the strip and not directly to the solder. Once sufficient heat has been applied to the area, start introducing solder.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split, solder, and reseal a

3. Follow steps two through five located at the top of this post for soldering a standard RGB strip light.

4. To reseal the strip light, apply

The LED strip lights are now connected, and power should flow through the entire length of the weatherproof strip.

Some electrical problems are harder to detect than others. That’s why, when trying to diagnose home problems, one of the best ways to quickly get to the bottom of the situation is with an infrared thermographic inspection. But what are the benefits of this inspection? Let the experts at Kolb Electric help!

When combined with traditional home inspection techniques, the infrared thermography inspection method reveals considerably more about your house than can be seen with conventional inspection tools. Some things our infrared thermography inspections have detected include:

Over the years standards for building homes have improved to offer more safety and reliability. Unfortunately, there are still homes out there with old electrical wiring in them that could cause electrical hazards. These old wiring types (knob and tub wiring) should be replaced as they can result in extensive damage to your home over time if not properly taken care of. Know what to look for in your home and upgrade your wiring.

There are several common signs that can indicate your home’s wiring may be old and out-dated. If you notice these issues occurring in your home, it may be time to contact an electrician and have a home electrical inspection. Common signs are:

Knob and wiring tubing can be found in homes built around 50 years ago. If properly maintained, knob and wire tubing can be safely used in your home. But often over the years the wiring can begin to crack and break down leading to exposed wires. Because of the age of the wiring it often will not reach current code and can prevent your home from being insured in some cases. Overtime knob and wire tubing can heat up and requires sufficient air space around the wiring. Any contact with insulation or wood can result in a fire.

In some cases you could experience some of the issues listed above and you don’t have knob and wire tubing. In many cases, when a home was originally built it was brought up to correct standards and has potential hazards all over. If you are unsure of the status of your home’s electrical wiring or you are experiencing some of the signs listed above, we highly recommend that you have you’re home inspected. An electrical inspection can catch potential hazards and also lead to better electrical efficiency.

To schedule a home inspection, contact your local Expert Electric at 604-681-8338.