Many homeowners don’t know when the time is right for home generator repair in Mount Vernon, and will simply allow their generator to go to waste. That’s unfortunate, because a generator can come in handy during a particularly rough storm in terms of supplying power to any of your home’s appliances. You’ll able to tackle some work-related tasks on your computer, binge watch your favorite television show, and store leftovers from last night’s dinner all while a storm blows over. However, you may have to get used to living by candlelight if you don’t seek generator repair soon enough!

Think you need generator repair? Call Beacon for assistance when you notice these 4 signs:

Regardless of bends, twists, or turns, Example of a cut line on LED strip lights

2. You will now have two LED strip lights. Carefully peel back the end portion of the paper strip covering the strip’s adhesive backing, and then remove the 3M VHB adhesive from the solder pads on the bottom side of one of the strips. The strip with its adhesive peeled back will be the top strip when soldered.

5. Align the non-tinned strip segment (strip with adhesive removed) directly over the newly tinned pads, and apply heat. Hold the soldering iron in place until the solder remelts and begins to flow. To strengthen the bond and improve visual appeal, a small portion of solder can be added to the top pad.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split and solder a run of non-weatherproof two-conductor or connecting wires. Peel away the blue wire so that only the positive (red), negative (black), and control (green) wires are left.

*No wires should be peeled away if you’re joining single-color or standard RGB light strips.

3. Properly heat your soldering iron. For best results, clean and tin the tip of the iron immediately before soldering. To tin the iron, touch solder to both sides of the iron’s tip.

4. Next you will need to tin the solder pads on both ends of the split strip light. When soldering, always apply heat to the target area on the strip and not directly to the solder. Once sufficient heat has been applied to the area, start introducing solder.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split, solder, and reseal a

3. Follow steps two through five located at the top of this post for soldering a standard RGB strip light.

4. To reseal the strip light, apply

The LED strip lights are now connected, and power should flow through the entire length of the weatherproof strip.

Make sure that the voltage of your LED light is compatible with the truck’s operating voltage. For example, you wouldn’t want to use a 6-volt light with a 12-volt system. That bulb will burn out very quickly. Or say you use a 24-volt light on a 12-volt truck—if you get any light output at all, it wouldn’t be near what is possible from that light.

When you’re installing new LED truck lighting, lubricate sockets, terminals, or any associated electrical connections with dialectic grease to seal out moisture and prevent corrosion. Because the grease can dry up, you should check connections periodically. It’s important to keep connections lubricated to maintain the functionality of your light. However, too much grease can interfere with the terminal/socket connection and prevent a light from functioning.

Be sure to know and understand the rules set in place in the light’s warranty. Doing unauthorized repairs or disassembling the light will most likely void its warranty. A driver should also know the correct person to contact about their LED truck lighting in case of light malfunctioning. The point of contact could be the fleet’s parts department, the purchaser, or the company from which the light was purchased.

For technical questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

We all know or at least heard that converting from Metal Halide (High Intensity Discharge) to LED will save you money.

But how much? Are there any other reasons or difference you should know about?

In this article, we break down all the factors that you should be aware of before making a decision to convert from Metal Halide to LED. Here are the 9 reasons we think LED wins over Metal Halide.

Let’s take a look at the information on a typical 400 watt metal halide bulb. While specifications may vary, a visit to a popular online website that sells Metal Halide bulbs shows that a brand new bulb has the following specifications:

We have just as many customers wanting to convert to LED because of maintenance savings as they do for energy savings. Think about what we discussed, over the life of the LED retrofit kit, a customer would have to do 5-6 Metal Halide replacements. The higher the installation height, the higher the cost of replacement. And if you have a facility loaded with lights, this becomes a significant budget amount every year that you must take into consideration. Now, we know that reduced maintenance time on lights does not translate into dollars saved because it is highly unlikely that people will lose their jobs over the fact there is much less work to do. However, these people will have time to now work on things that matter, like fixing the machines that make the company money instead on replacing lights that cost the company money.

When you take a measurement of light with a light meter, it reads lumens. And this measurement of all the lights that contribute to the light at that location creates a measurement called foot candles. But let’s think about that light that is being measured. Metal Halide creates all sorts of light, in all spectrum’s, visible or otherwise. This includes UV and IR spectrum’s, visible to the measuring device but not visible to the human eye. LED, on the other hand, does not produce UV and IR. Therefore, its readings using the same light meter is only picking up visible spectrum’s.

So there is a fun little test you can do. Have 2 light sources, LED and Metal Halide. And first ask, which one is brighter? And if the right LED source was selected, they should say LED. And then use a light meter, and the light meter may say the Metal Halide area is producing more foot candles. And so now you know part of the reason, but wait, there’s 2 other pieces of information you need to know.

Click here to see our infographic on Retrofitting vs Replacing.

Conclusion