If you’re in the midst of a renovation or simply rearranging your floor plan, then you’ve likely come across the need to add or relocate a light fixture. Maybe your new dining room table is a little wider than the old one, you’re adding a kitchen island with pendant lights, or you’ve finally convinced your significant other to let you get that pool table you’ve always wanted. In any case, you need to move or add a light fixture – but how and when?

First, it should be noted that, contrary to how it may seem, most light fixtures are not connected to a joist or even drilled into wood. Instead, hanging light fixtures and ceiling lights alike are located between joists and supported by electrical boxes that grip a wide surface area of the sheetrock that makes up your ceiling to support the weight of the fixture below; for heavier fixtures, like large chandeliers or ceiling fans, there are larger, even joist-secured boxes that will need to be used.

If you’re moving a light fixture, it is important to note that there are certain limitations as to where the fixture itself can go. If you wish to relocate the fixture to a place where a joist exists just above, then you’re likely going to have to use a swag hook and chain to anchor the fixture in place, as a box under a joist is not an option. That said, if you’re moving the housing for the fixture itself, you’ll need to know which direction the joists above run, then choose to move it either through the same joist cavity or drill through a joist to run the current wiring to the new housing. Other things to consider include which switch controls the light and where it is located, as it is a safe bet that a wire will have already crossed all joists above (at some point). This can prevent your electrician from drilling needlessly by allowing them to fish the wire back to the earlier point. If your switch is further away than the destination, you can bet they’ll have to do some drilling. Jumping through, between, and around the joists in the ceiling represents the largest obstacle your electrician (and light fixture) will face.

Once your location is set, all that is left is to get your electrician out to assess and perform the work for moving your box. If you’re planning on doing one large fixture over a pool table, island, or entire room, then you’ll want to take into account the power output of the fixture compared to what that circuit can safely allow for as well as the weight of the fixture. A typical rule of thumb is that anything under about 35 pounds can be handled by a standard drywall box, but something more (or with a fan) will need extra stabilization. Surprisingly, if you’re running numerous small pendant lights, the electrician may have an even easier time running the circuit and ensuring that your lights are up and running in no time. Just be sure to discuss the fixtures you have in mind with your electrician before you purchase them to know what they believe your limitations are!

Whenever you need electrical work done around your Des Moines home, contact the experienced professionals at Electrical Gurus. We are proud to offer the finest licensed local electricians in the area and are always more than happy to help out on your household projects.

Electricity is something we can’t manage without, but it’s crucial to take due care while using it. When it comes to electrical safety, you can never be too careful, and it’s important to ensure that the electrical systems, wiring, fixtures and fittings in your home have been installed by a licensed and insured electrician.

The same level of care has to be maintained when you are using any electrical appliance and you must ensure that you don’t overload the system while operating any of them. It’s very common for people to use extension cords in their homes and not many property owners feel these electrical accessories should be included in their safety checklist.

If an extension cord is used continuously under the wrong conditions, it can potentially lead to electrical shock or even an electrical fire. We have put together a few extension cord safety tips:

The other important thing you should keep in mind is that you should never join two or more extension cords together. This can be very dangerous because that can cause a drop in the voltage in the cords; this reduces the effectiveness of the circuit breakers and safety switches in your home; in turn, this can result in an overload.

If this occurs, the strength of the actual current that’s flowing in the cords can damage appliances which can create a fire hazard & potentially cause electrocution. While an extension cord can be quite helpful in effectively delivering power to points where you need it; never forget that using an extension cord is just a temporary measure and shouldn’t be used to provide permanent power.

Some would argue and say that they have been using extension cords for years without any trouble; however, that doesn’t really mean it won’t compromise the electrical safety in your home, when you plug it in the next time. If you find you are using too many extension cords around your home, it’s an indication that there aren’t enough power outlets in your home, to cover your needs.

It’s best to call in an electrician, discuss your electrical requirements and get them to assess whether the existing installations meet them. For more information, simply speak with the experts at Allround Electrical and take their advice on various aspects of CBUS installations. The number to call is – 1300 169 263. You can also write to us at this email address.

Thanks for reading,1300 169 263

Help for Heroes, an organization that aids wounded soldiers in the UK. Munro’s inspiration for the exhibit:

Two years ago I was riding my bicycle in the lanes near my workshop – it’s a very good way to keep fit. But that winter afternoon it was dark and my lights had failed, and I fell off into a ditch full of icy cold cow-poop. As I got to my feet, the idea of cycling in a warm, dry, well-lit environment seemed irresistibly attractive. Almost immediately when I got home I started sketching the Star-Turn bike. – Bruce Munro, his website. Here’s one more photo of the magnificent Star-Turn:

‘Tis the season to be jolly with thousands of colorful lights glowing from your trees, gutters, front door wreath, and bushes. Billions of lights will be used to dress up homes and businesses throughout the country during the final months of the year. As festive as the light-up Santa and Rudolph may look on top of your roof, you have to make electrical safety the focus of your holiday lighting festivities.

Following are five tips to help you avoid common holiday lighting problems others will experience this year. Commit them to memory so electrical safety does not pull the plug on your merry-making décor this year:

1. If you are putting up a live Christmas tree, make sure it is well-watered and use LED bulbs for all decorations placed on the tree. Dry trees and heat from non-LED bulbs create home fires every holiday season. Do not place candles where they may be knocked over on a live tree. LED bulbs should be used when decorating trees in your outdoor landscape as well.

2. Thoroughly inspect every string of lights and plug-in points before using them indoors or outdoors. If you notice any of the following at even one point on the string, toss it out or repair the damage before use to ensure electrical safety for your home:

3. Power cords should be used to connect strings of lights, but pay attention to how many strings you are connecting per cord. In general, more than three strings of lights could be too much.

4. Avoid hanging your lights with tacks, screws, or nails. You do not want to crack, tear, or otherwise damage the electric cord. You can use insulated hooks instead.

5. Make sure you are plugging outdoor lighting features into ground fault circuit interrupter outlets. These outlets reduce the risk of electrical shorts or dangerous shocks if water, wet leaves, and other outdoor elements get into the sockets.

6. Do not use indoor-only holiday lights outdoors. There are clear differences in how these types of lights are made, even if they look the same. For instance, outdoor lights are created with more insulation so they are not as easily affected by rain and snow.

Do not allow electrical safety to cut the cord on your holiday lighting festivities. Light up the house and allow the big snowman to wave at the neighbors from your front lawn. Just make sure your snow globes, trains, and twinkling tree lights present no danger to your home, your family, and your neighborhood.