For the photo shown to the right, taken at night in a Texas ghost town, Danser assembled the following items: a powerful, handheld LED light; his Canon 5D Mark iii camera and Canon 16-35 mm L lens (at 16mm); Canon 580ex 2 flash; a red gel (piece of red cellophane to color the light of the flash); a tripod; and his girlfriend’s finger (to graciously hold down the shutter release button because he forgot his bulb release at home!).

Danser told Pegasus: “So, I set my camera on bulb mode and had my girlfriend hold down the shutter release button for 13 minutes, while the camera was very sturdy on the tripod. The place was pitch black except for the stars and the moon (very little ambient light pollution in the desert). As my girlfriend was keeping the shutter open, I walked to one side of the structure and methodically shined my flashlight (rated at 2000 lumens, so it’s pretty bright) all along the exterior and front facade of the building. This lasted for about five minutes before I turned the flashlight off and ran to the other side of the building and ‘painted’ for another five minutes.”

Danser said that one of the important tricks of light painting is to show off the textures of the buildings by shining his LED flashlight at an angle instead of from the camera position.

After “painting” the sides of the building for five minutes each, he ran inside and popped off about 10 red-gelled flashes to create the effect of a warm glow pouring out of the building.

When asked how he was able to run in and out of the building without showing up in the photo, Danser simply replied that “The camera could not ‘see’ me because I was moving quickly, and there wasn’t enough ambient light to expose me in the picture.” While popping off the gelled flashes in the building, he always made sure he was not visible to the camera.

After 13 minutes at an aperture of 2.8, Danser was able to get an excellent exposure of the night sky while having ample time to do all of the “light painting” that he had planned beforehand.

Soon I hope to try some light painting of my own with less expensive equipment to show you how anyone can adopt Danser’s technique. After all, light can be used in all kinds of art and photography projects.

In the meantime, check out this Danser’s website to see tons of beautiful experiments playing with—and painting with—light. Thanks, Matt!

Outlets and switches in Fairfax, VA are often taken for granted. So much for granted, in fact, that it’s almost amazing to consider what life in your home would be like without them. Without outlets, you wouldn’t be able to charge your cell phone or laptop. Without switches, you wouldn’t have any lights for the rooms in your house. It sounds ridiculous to even consider, but it’s a real possibility if you don’t replace them periodically. While outlets and switches can provide you with power for years, there will come a point where they need to be replaced or else be a liability and, ultimately, a safety hazard.

Add the perfect custom finish to the front of your home with outdoor hanging lanterns and wall lanterns.

When using two outdoor lanterns, they should measure about 1/4 the height of the front door(s). When you are using only one lanterns, 1/3 of your door height is appropriate.

Outdoor hanging lanterns should be centered over your front door(s), high enough so that the doors may open and close freely. If you have a picture window or archway above the front door, center the fixture so that it may be seen from inside your home.

Wall lanterns surrounding the front doors should be proportional to your home, when in doubt, size up! Remember, fixtures appear smaller from curbside viewing than most people would imagine.

Wall lanterns are also appropriate for rear and side entrances and by garage doors – same rule of thumb for sizing applies for these areas.

Path Lighting should be placed 6′ apart to ensure adequate beam spread.

Be sure to make your space functional! Task lighting is an important piece of the design; it will provide guidance and illumination in the necessary areas to ensure safety.

Focused illumination on key holes and security pads allows for easy access when you are entering and leaving your home at night. Outdoor LED wall lights or recessed spotlights work well in these areas.

Add path lighting to walkways every 6’ to provide adequate beam spread. This will create curb appeal ambiance and visibility when walking at night. Don’t forget to add light near the house numbers – this can help in emergency situations and for deliveries!

After the sun goes down be sure your home has the same curb appeal as it does during the daytime by adding outdoor and uplighting to the landscape.

Illuminating trees or other elements from below will create soft focal points in the landscaping after the sun goes down. Use a flashlight to test where you’d like the light to hit, then mount the fixtures accordingly. Be sure to mount fixtures out of grass for ease of mowing and other landscaping tasks.

Be sure to view your outdoor lighting after dark before signing off on a project; it’s easy to make necessary adjustments to refine your outdoor lighting design.

To avoid being “that neighbor”, be sure to eliminate glare and make sure your outdoor light fixtures do not create “light trespass” into your neighbor’s property.