Maintenance Factor

Illumination Systems are designed to fulfill the required lighting level at the end of an operation term and not at day one of the new installation. The luminous flux of the system is going down over lifetime. This is a normal process, no product is lasting forever but the required illuminance levels should not be depreciated at any time. If a lighting system is setup, the maintenance plan has to be fixed too. So the facility managers know how often to clean the room, the luminaries and how frequently to change lamps. A reasonable time needs to be found between maintenance and operating hours, as maintenance cycles are connected to costs. The longer the operation time without maintenance, the more luminaries need to be installed to guarantee the required illumination level at the end of the term. The more frequent the maintenance cycles, the higher the maintenance factor, but also the related costs for the facility service.

Which Points are influencing the Maintenance Factor? Different factors influence the decrease in lighting level like the soiling of the room surfaces, the soiling of the luminaries, depreciation of luminous flux by the light sources or lamps failure.

Room Surface Maintenance Factor: The room surface maintenance factor is the ratio of the room surfaces reflectance before and after cleaning. It is the reduction of the lighting level according to soiling of the room. Luminaire Maintenance Factor: The luminarie maintenance factor is the ration of the luminaries luminous flux before and after cleaning. It depends on the luminarie construction and design (open housing or closed one) as well as on environmental conditions (dirty or clean). Lamp Lumen Maintenance Factor: The lamp lumen maintenance factor is the ration of luminous flux at a specific time compared to a new lamp. It is describing the aging of the lamp or the reduction of light intensity over time. Manufacturers offer comprehensive tables about their lamps luminous flux behavior. Lamp Survival Factor: The lamp survival factor depends on the service lifetime of a lamp. Some lamp lifetimes are reduced by frequent switching. The lamp manufacturers provide tables indicating the lamp survival factor. If a lamp is not working any more, the decision for immediate replacement or group replacement needs to be taken. If the lamp is replaced immediately (mostly in areas where the luminaire is easily reachable) the LSF can be set 1. On the other hand, the decision could be to replace lamps in special terms or group-wise. This could be the case in huge halls, where machines need to be stopped to reach the luminaires.

A maintenance factor of 0.8 shows, that the new lighting system needs to be over driven by 25% not to undercut the minimum required illumination level after 10 years. LED lighting systems are flexible and easy to connect to control systems. The installed load will provide efficient luminous flux at the end of the operation time but the energy that is “over” in the beginning can be saved. The new installation would illuminate an area with required 300lx by about 450lx. The energy can be saved by lighting management systems that are regulating the power concerning the luminous flux depreciation. HID lamps are not easy to control. The energy load that is “over” in the beginning is wasted. No change to save it.

Conclusion: Think carefully when setting up a lighting installations maintenance plan. This starts already with the choice for the light source. LED Modules are efficient, likely not failing and offer long lifetimes between 50,000h and 100,000h. The control possibilities are comprehensive. The luminaries overload, that needs to be installed to guarantee the end of lifetime illuminance levels, can be saved by light management systems. Regarding all the mentioned points, LED is the competing light source. The features are dominant over traditional light sources. Take the chance and install or renew your lighting system by  energy efficient LED light sources and luminaries. If you have further questions please contact the lighting experts at MyLEDLightingGuide.com and discuss products as well as solutions.

Here in Massachusetts, our electricians are used to handling all type of electrical systems and services. We also have our share of older homes, and with older homes come aging electrical systems. An expert upgrade provided by a trustworthy electrical contractor can offer your home various benefits.

If you’ve experienced issues with your electrical system recently, or even if your electrical system is functioning fine but depends on older technology, it could be time to seriously consider an electrical panel upgrade/ replacement. But what are the benefits of such an upgrade? We’ve shared a few advantages below.

You may not know it, but upgrading your electrical system might actually be legally necessary. This is because many older models no longer adhere to modern statutes and codes. Typically, if your panel still uses fuses and other outdated equipment, it probably isn’t up to code and will require a replacement.

Even more important than upgrading to legal building codes is protecting the safety of your home and your family. Old or worn electrical panels can cause an overload. This can short out your electricity and potentially even cause a fire. A newer electrical panel can provide increased safety for your home.

Today’s homes have an increasing amount of appliances and electronic devices in them. From plasma screen TVs to high-end computers and similar devices, our electrical systems play a larger role in our lives than ever before. As such, an improper electrical panel, you won’t be able to support the kinds of appliances you need to stay connected.

What you need is an up-to-date electrical panel that meets all of your electrical needs while keeping your home up to code and your family safe. Remember, electrical work can be dangerous, so don’t leave such an important project in the hands of amateurs. Also, do not be tempted to take this on as a “DIY” project, as this can do more harm than good.

By Clarissa Allison | April 22nd, 2016

Lighting an awkward or unusual space can prove to be a challenge but also lots of fun when one learns to expand their initial thoughts about what is possible when decorating. Below, read on for a list of tips on how to light your narrow living room or industrial loft with ease! Click the pictures to be brought directly to the product pages in question.

Make It Modern

Museums have a hard line to walk, exhibiting items for public education and enjoyment while protecting those same collections from damage. Today’s museum also carry the additional weight of safeguarding the future of the environment – as well as their financial future – against the dangers of unnecessary energy consumption. What advancements have been made in preservation lighting technology to help accomplish these goals?

Light, including all three types: ultraviolet (UV), infrared, and visible light, causes permanent and irreversible damage to museum pieces. Cumulative and dependent on the intensity and duration of exposure, light affects chemical composition, physical structure, and, the appearance of a collection. There is no conservation treatment that can repair it. Light damage is forever.

Only complete darkness ensures conservation, since exposure to light in any form naturally breaks down items. However, keeping pieces locked away in the dark defeats the mission of the museum – sharing those works with the public. It is thus a museum’s dilemma to find a suitable solution that balances the best of both worlds, in addition to considering energy costs and the environmental impact of its lighting selection.  

In your search for preservation lighting, you will find that a great deal of lighting solutions involve UV (ultraviolet light), the most energetic and destructive form of light. These include natural light, fluorescents, HID, and tungsten halogen lighting. Fortunately, the effects of UV can be controlled with simple filters, offering a greater variety of lighting options. UV filters are hard plastic tubes or soft sleeves wrapped around bulbs/light sources, which filter and block up to 98 percent of UV light, preventing its damaging effects. NOTE: UV filters lose efficiency over time and must be replaced every eight-10 years.

Specific, detailed recommendations for preservation lighting levels based on your collection type can be found from various sources, including the Library of Congress, National Park Service, UNESCO, and more.