Is your LED bulb blinking too fast? No worries—it’s an easy fix! LED lighting draws much less power and lasts way longer than standard incandescent lighting that comes stock with most vehicles. Although the reduced draw of LEDs has advantages, replacement of turn signal bulbs with LEDS will cause what is called hyperflashing. Hyperflashing is when the turn signals blink faster than your stock incandescent bulbs did. This happens because your new LED bulbs draw such little power that your turn signal relay sees the bulbs as being out.

Installing an ixing hyperflashing. These modules are economically priced and are usually simple to install. In most cases, these flasher units are little circular or square boxes with metal prongs sticking out one side that simply plug into where your stock flasher went. Our LED flashers function with both LED and incandescent bulbs, so even if you have LED turn signals in the back and incandescent bulbs still in the front, you can use our LED flasher modules with no problems. Before you order, compare the pin diagram of the stock flasher with the pin diagram of our flashers on our website.

For technical questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

A significant number of homes in Baltimore and Bethesda, MD, Alexandria, VA, and Washington, DC built between the mid-1960s and the first half of the 1970s have hazardous aluminum wiring rather than copper. During that time, aluminum wiring was considered safe to use and viewed as a cost-saving measure. The U.S. Consumer Product Safety Commission (CPSC) now believes aluminum wiring poses a safety hazard in homes that still have this type of wiring.

The biggest danger associated with aluminum wiring is that unanticipated fire hazards arise from the oxidation and deterioration caused at the points where aluminum wiring is connected at outlets, light fixtures, and splices. While this can cause overheating and arching that won’t trip a circuit breaker, it can cause a fire. Aluminum wiring was used in an estimated 2 million homes between 1965 and 1973—and many of these homes are located in the MD, VA, and DC area.

If you’re concerned about dangerous aluminum wiring, pay attention to the following warning signs:

All of these signs indicate a potential fire hazard for standard aluminum wiring.

Aluminum wiring should be thoroughly evaluated by a qualified electrician who is experienced in inspecting and correcting wiring problems. The CPSC recommends a few methods for correction. The first is to rewire the home with copper wire, an expensive option that really only makes sense if the homeowner is already in the process of completely remodeling or doing deep renovations. The second option is to use the Copalum crimp method to correct the problem. This involves attaching a piece of copper wire to the existing aluminum wire with a specially designed metal sleeve and powered crimping tool. It is a permanent repair option that will eliminate the dangers posed by aluminum wiring. A third option is to use a UL listed copper to aluminum connector to attach a copper wire to the existing aluminum wire.

Only an experienced electrician can accurately determine the level of danger a home with aluminum wiring faces, and then fix the problem in an efficient, timely manner.

If your home has aluminum wiring, we recommend that you call Kolb Electric or contact us online. We will send one of our expert electricians out to evaluate the aluminum wiring in your home to determine the best option to make your home as safe as possible. We’ve been serving Baltimore and Bethesda, MD as well as Alexandria, VA and Washington, DC since 1925. You can count on our experienced electricians to get the job done right the first time.

Available in a variety of shapes and sizes and with multiple base types, these long-lasting LED bulbs are perfect for an elegant, vintage look. Chips-on-board (COB) LEDs imitate the look of thin filament wire in antique-style bulbs and emit a rich, warm white or ultra-warm white color. The decorative bulbs are great for many applications, such as chandeliers, wall sconces, ornamental fixtures, and light strands, and they consume only a fraction of the energy consumed by incandescent bulbs.