The kids are grown and have homes of their own, so it’s time to make those empty rooms into that den, office, sewing room or home theater that you’ve been wishing for over the years. Or, perhaps you’d like to update your kitchen with new appliances or add some new, luxurious bathroom lighting fixtures. Maybe you’ve been thinking about a whirlpool bath. Why not? However, don’t forget to give your local electrician a call as you’re planning those changes. Chances are good that you’ll need a few electrical upgrades to make sure your wiring system is ready to handle the increased load. Consulting an electrician in Pasadena who is licensed and knowledgeable about home renovations can help you keep you avoid last minute complications as your project gets underway.

Electrical system upgrades are often an afterthought when homeowners start planning a remodeling project. Often, the plans are made and the new appliances, lighting and other electrical components chosen before the very basic issue of how to power them is discussed with an electrician. Pasadena homeowners, for the most part, just don’t stop and think about things like electrical load distribution and wiring system capacities when picking out that new, streamlined refrigerator or over-the-range microwave. However, forgetting to plan for those practical things can lead to unexpected costs when the need for electrical upgrades to make it all work becomes apparent. Including a licensed and bonded electrician in the initial planning of your home improvement project can ensure that necessary electrical work is budgeted in from the start, eliminating unpleasant surprises.

If you’re planning a remodeling project and have yet to choose an electrician in Pasadena homeowners won’t find an electrical contractor than H Electric. With more than twenty years of experience with remodeling projects in the Pasadena area, we offer knowledgeable advice and quality electrical services to ensure that your project turns out right. And, every job we do is backed by our famous lifetime guarantee.

Click here to read more

In the late sixties, and early seventies aluminum wiring began to be used because most available copper was going to the Vietnam war effort. However, aluminum wiring is not ideal for small home electrical systems.  The electrical devices at that time were not designed to handle the high temperature coefficients of aluminum wiring. Aluminum wires can also expand in diameter and length as they get hot, they can actually back out the screw terminals, causing a loose connection. This, in turn, can cause heat, which can ultimately lead to a fire.

After problems with aluminum wire termination became known—including one notable house fire—the UL (Underwriters Laboratories) and other agencies adopted new safety regulations and put more restrictive standards in place. However, many homes from the 60s and 70s still do not have safe aluminum wiring terminations. But there are a number of ways to solve this problem without having to rewire a home.

Consumer Safety Council Recommendations

According to the Consumer Safety Council, there are only two approved methods that splice aluminum wire to copper wire:

These standards have caused acceptance problems with home inspectors and insurance companies, which has led to homeowners paying 2 to 4  times as much as they should to have their aluminum wiring terminated.

The power goes off and on at random times and often when you least expect it. When it happens, it is a minor nuisance that requires you to reset clocks and turn back on whatever appliance you are using. You don’t typically think of that few seconds of the power going off and then going right back on as serious. It is. Those little power outages are killing the life of your appliances and damaging your sensitive electronics. Every time the power flickers or surges, anything that is plugged in is basically getting a jolt. An electrician in Los Angeles wants you to save your electronics and appliances by investing surge protection. The team at The Electric Connection can get your home protected in just a few short hours.

Every day, little surges of electricity are sent through the lines and into your home. You may hear your refrigerator compressor kick on when nobody has left the door open or your lights may get suddenly brighter or dim. These are all signs of a power surge explains an electrician. Los Angeles homeowners may notice these things happen if they run more than a couple appliances at a time or when something like the AC unit kicks on. The electricity is pulled from the other appliances and electronics to run the AC, which is a lot like cutting off the supply. This makes everything else, including the AC, work a little harder and not run quite as it should. This is what causes the damage.

The fix is to have a whole house surge protector installed at the electric panel by a Los Angeles electrician. This will control the electrical flow and prevent those surges from happening. If the power goes out and comes right back on, the surge protector will prevent any one appliance from getting a jolt of electricity that may fry the board. Give The Electric Connection a call today and schedule your surge protection installation.

Limit switches, as the name suggests, are precision switches that are designed to work as limiting devices. The switch is typically snap-action and designed to sense the presence, absence, or be triggered by an excess or lack of physical contact at the position where it is installed.

The flexibility and adaptability of limit switches to different tasks and environments has made them very popular as components of conveyor belt systems.

Industrial conveyor belts are considered to be amongst the greatest inventions for boosting production, as well as reducing time, costs and manpower requirements. They are commonly used in production, mining, assembly lines and just about every major industry or sector today.

They typically consist of a number of pulleys that rotate under a continuous belt. Some of these pulleys are powered and they drive the belt, keeping any material on top continuously moving towards its destination.

Conveyor belts can be broadly classified into two classes, which are:

These conveyors are used for transporting smaller volumes of material like packaged goods, or lighter materials like boxes.

These are heavy duty conveyor systems which are designed to carry heavier loads or bulky materials, like industrial and agricultural goods.

While conveyor belts can tremendously increase efficiency, they are prone to jamming from over-loading unless the correct safety measures are put in place. Limit switches help prevent this by measuring the height or number of individual products passing through the conveyor system. In case the switch senses an object that may cause an obstruction, it shuts the system down to prevent damage or spillage.

Depending on the environment and purpose, there are a variety of limit switches which can be used in conveyor systems: