If you are like most families, you probably have an extension cord – if not multiples – around your house. But did you know that these are among the most dangerous electrical appliances in your home? If not used properly or cared for appropriately, an extension cord could be the cause of fatal injuries, electrocutions, or even a house fire.

Not all extension cords are the same and it is important to select the appropriate extension cord for your needs. The next time you go to grab the same old extension cord, ask yourself these three questions that will help you determine whether it is appropriate for the task at hand.

If you are looking to use an extension cord outside, you must check to make sure that it is equipped for such. An outdoor extension cord has tougher insulation/jacket allowing it to withstand moisture, temperature change, UV rays, etc. An extension cord that is safe for outside use will say so clearly on its packaging. If you are not sure, contact the manufacturer.

The length and gage of your extension cord will determine the wattage rating of the cord. Ensure your device(s) wattage doesn’t exceed the cords wattage, this could cause overheating and/or a fire. The wattage of a device is generally found on a tag attached to the cord. Again, if you are not sure, contact the manufacturer to clarify. Better safe than sorry!

Another important consideration is the length of time that you are using the extension cord. An extension cord is only intended for temporary use. Leaving an extension cord plugged in will cause electricity to continue to circulate through the device and could potentially cause overheating, a fire or defects to the device. If you are looking for a permanent fix, look into installing more electrical outlets around your home and plug your device directly into the outlet.

For more information on how to ensure the safety of your home and devices, contact Expert Electric at 604-681-8338.

LED light bulbs and fixtures are the best alternatives for many reasons.

LED lights are available in several shades of white. These shades are referred to as a bulb’s correlated color temperature (National Institute of General Medical Sciences, states that, “Circadian rhythms are physical, mental and behavioral changes that follow a roughly 24-hour cycle, responding primarily to light and darkness in an organism’s environment.”

According to writes, “Several studies have documented the importance of light in reducing depression, decreasing fatigue, improving alertness, modulating circadian rhythms, and treating conditions such as hyperbilirubinemia among infants. Further, the presence of windows in the workplace and access to daylight have been linked with increased satisfaction with the work environment.” Windows are the best method of accessing daylight, but cool white LED lights along with the right color temperatures at the right times, can have the same effect on the body.

Warmer color temperatures lead to the release of melatonin, which causes drowsiness. This is appropriate during bedtime hours, but causes problems for those who need to stay awake, such as overnight nurses and doctors. Introducing natural or cool white light to hallways, operating rooms, and nurse stations can help hospital staff, especially overnight workers, feel more alert and energetic.

EPA has a list of cleanup procedures, such as having everyone leave the room, opening a doors or windows, shutting off heat and air-conditioning systems, and other specific instructions.

Fluorescent and incandescent bulbs also emit low doses of UV radiation that can damage not only facility materials but can also damage skin and eyes. According to a CBSLA.com discusses the results of another study that had similar findings. In this article, it is said that, “. . . exposure to the (fluorescent) bulbs could lead to premature aging and cancer.”

Continued UV exposure is also harmful to the eyes. A LED lights won’t flicker or emit any color spikes. Color fluctuations and flicker can cause negative effects, such as headaches and dizziness. When used for hospital lighting, LED bulbs and fixtures can improve overall health and eliminate the possibility of additional health risks posed by fluorescent and incandescent bulbs.

Seeing colors as they truly are is critical in health care environments. Inaccurate color rendering of skin or blood could lead to a misdiagnosis or failure to see signs of infection or jaundice. The spectral graph below can be helpful in understanding the advantage of high-CRI light sources. Lights with a low CRI will show fewer colors while high-CRI lights cover more of the spectrum. A light source’s ability to show more colors increases its accuracy in revealing the true colors of people, objects, and surroundings.

FreemanWhite, a health-care-focused design firm reports, “. . .light fixtures with a high CRI . . .  help caregivers assess rashes, lesions, and skin pigmentation.” They go on to say, “In the interest of avoiding liability claims, better lighting quality can enhance a caregiver’s ability to diagnose correctly, identify reactions, prevent secondary infections, and minimize readmissions.” High-CRI LED lights can also help prevent medication errors.

Another method of LED hospital lighting control is the use of occupancy sensors. These sensors will save money beyond those that result from reduced energy consumption. Sensors will also extend the life span of bulbs and fixtures even further by turning them off when no one is in the area. These sensors are best suited for low-traffic areas.

Prisons and correctional facilities are full of security threats, it’s just common sense.

That is why it’s a major task and a seemingly forever ongoing one to try everything in the book to reduce threats and increase security for everyone in, near, or even outside the facility.

Today we wanted to address how we can solve 2 major correctional lighting system and things you should look out for when finding fixtures perfect for your building and budget.

Firstly, a LED prison lighting system will reduce indirect stress and irritability in both inmates and staff.

Secondly, LEDs within correctional buildings will improve detection of movement, which we all know is crucial.

How you ask? Well, lets talk about each one individually and break it down a bit more than just one sentence. From there, we will talk about how to go about making the conversion over to LED, like we mentioned at the start.

Have you ever been around a light that was flickering and or buzzing? It can get annoying, and fast. Imagine living under these conditions, everyday all day; no break other than a few hours when you go outside. Sounds like no fun, and it can lead to some serious stress and irritability issues for both inmates and staff.

For obvious reasons, additional stress on inmates will never produce a good outcome for anyone. But, another important point is that this can effect your staff and guards too. It can affect their ability to perform at full capacity, which in combination with highly irritable inmates is not a good mix whatsoever.

With LED technology, they will never be susceptible to flickering nor buzzing. Not even near the end of the lights lifespan will they flicker or buzz, unlike other technologies commonly still used in such facilities. Thus, you can avoid any stress or irritability which may be caused from flickering / buzzing lights.

If you can’t tell where everyone is at every second, you’ve got an issue. This is especially important for outdoors during the time when it is dark out. Sure, some light is better than none; but why jeopardize your operations with a flickering light when you could upgrade to LED and get rid of the issue entirely?

As you may or may not know, flickering lights make it harder to not only detect movement, but also identify humans. Think of a strobe light, it’s a bit harder to actually make out what is going on entirely. This holds true with a flickering light, even if it isn’t as bad as a strobe light is.

Here we are going to list a couple of the other major general benefits that LED technology offers over other technologies such as metal halide, HPS, fluorescent, and similar.

There are really only two routes you can take, LED retrofit lighting kit will work perfectly. On top of that, retrofitting is a much cheaper option (typically) then a full replacement is. So, if you don’t need to fully replace then stick with retrofit kit LEDs and you will save a lot on your lighting system investment.

Conclusion

Flaws can always be picked at, especially in such tedious and unpredictable environments like the one we are discussing in this topic.

Electric cars are increasing in popularity as more people realize how economical the cars are. Gas prices are constantly on the rise and people are desperate to find a way to save money. Not to mention, electric cars are great options for those who are interested in preserving fossil fuels. If you have bought an electric car already or plan on purchasing one, you are probably interested in learning about how you can charge the car.

Your electrician in Glendale explains what you need if you are planning on charging your car at home. Depending on where you live, this may be a necessity. While public charging stations are becoming more popular, it is not always convenient to drive to a station and wait. At The Electric Connection, we understand the desire many people have to install a charger in order to charge the car overnight or whenever the car is not in use.

Electric car chargers are available in two main sizes. The smaller, slower charging station can be plugged in virtually anywhere. This station will not typically require an electrician’s help. The only time you would need to call a Glendale electrician is if you do not have enough outlets near where you park the car or you need an additional breaker to support the charging station.

If you are interested in the stations that charge the car in half the time, you will definitely need an electrician’s services. A new, higher voltage outlet will need to be installed. Depending on the current breaker panel in your home, you may also need an electric panel upgrade. A dedicated breaker will need to be installed that will be solely for the car charger.

If you are interested in learning more about your electric car charging options, please give The Electric Connection a call. We would love to assist you.