Let’s face it—halogen and incandescent headlight bulbs are a thing of the past. fanless, driverless LED headlight bulbs were used in this installation.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points. Repeat these tape lines for your other headlight.

6. Remove your headlight assembly if necessary, remove the current bulbs, and install your new LED bulbs. Check your owner’s manual for specific instructions on how to replace your headlight bulbs.

7. Depending on your vehicle, you may have to adjust your headlight beam before or after the assembly has been reinstalled. Your owner’s manual will explain how to adjust the beams. Align each headlight so that the top edge of the beam is at the same height as your horizontal line(s). If your headlights can be adjusted horizontally or produce two light cutoff points, use the vertical tape lines to align them properly.

3. Shake the vehicle to ensure that your suspension system is settled. For more precise adjustments, inflate all tires to their designated psi capacity and have someone sit in the driver’s seat. Also, make sure that your vehicle’s gas tank is at least half full.

4. Measure from the ground to the center of your headlight assembly where the bulb is located. This step must be done for all vehicles. If your vehicle allows for horizontal headlight adjustments in addition to vertical adjustments, it’s important that you also measure the distance between the centers of both headlight bulbs. The vehicle featured in this video allows for vertical headlight adjustments only; therefore, center lines aren’t necessary but are shown for demonstration purposes.

5. Turn on your low-beam headlights. Using painter’s tape, mark your headlight measurements on a flat wall. Measure from the ground up, and apply a horizontal line of tape to the wall; this line represents the top of your headlight beam. You can either apply one long, continuous line or small sections where the brightest areas of the headlight beams are shown.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points.

One of the biggest hazards of your home electrical system is the possibility of an electric shock. Whether there is an accident during an electrician’s work or there is exposed wiring that could shock someone inadvertently, this is a hazard that can cause serious injury and even death. Fortunately, by installing a ground fault circuit interrupter (GFCI), you can help limit the exposure to shock and minimize the danger. Read on to learn more about GFCIs and how they work.

Limit the Danger of Electrocution

Electricity is always trying to find its way to the ground any way it can. Unfortunately, sometimes the most convenient path is through a human body. That's why if you touch a live wire, the current will likely run through you on its path downward. The consequences of electric shocks can include burns, heart arrhythmia, nervous system damage and death. That's why it's essential to protect yourself from shocks around your home, especially if you are using electrical equipment that is likely to contact water.

Ground fault circuit interrupters work by constantly monitoring the amount of current running through a circuit. The instant that the current level returning from the circuit drops below the level going out – which could indicate that the electricity is escaping to the ground, possibly through a human – the GFCI trips and cuts off the power. The device should kick in in as little as 1/40 of a second, potentially saving  you, your family member or your electrician from electrocution.

Where to Install Your GFCI

There are three types of GFCIs available. One is the receptacle type, usually in the form of electric outlets with small black and red switches built in. You can also purchase portable GFCIs to plug into any outlet, and some electricians actually build the GFCI into the home circuit breaker. Any GFCI should have a test button so you can make sure it is working properly before using it – a well-functioning GFCI should trip as soon as you plug in a malfunctioning tool, saving you from even a minor shock.

Ground fault circuit interrupters aren't ideal for every circumstance – very long circuits, permanent motors and fluorescent lights are all prone to tripping the GFCI even when there is no danger. On the other hand, GFCIs can provide crucial protection in the kitchen, bathroom, laundry room and other areas where water could compromise a circuit, and are also useful when using power tools around water.

Protect Your Family from Electric Hazards

It's relatively easy to install outlets that have GFCI protection, and it could end up saving your life. If you are interested in installing ground fault circuit interrupters in your house, contact an expert electrician today.

One of the easiest ways to dress up your space and update the style is by changing your chandelier. Before you run out the door in search of the perfect chandelier, make sure you know the dimensions of your space. An appropriately sized chandelier should serve as a beautifying focal point that fits seamlessly into your overall design scheme.

For a room without furniture: Add the length and width of your room in feet, and then convert that number to inches. For example, a room that is 12 feet by 14 feet (12 + 14 = 26) would require a chandelier this is approximately 26 inches wide.

For a room with furniture: If you already have a dining room table in the space, the width of your chandelier should be about a foot smaller than the width of your table. This will leave a 6-inch clearance from the outer edge of the chandelier to the table’s edge.

The bottom of your chandelier should rest at least 30-34 inches above the tabletop. Adjust according to personal preference, fixture style and ceiling height. It is okay to hang your chandelier a bit higher in dining rooms with cathedral ceilings.

Chandelier height should be about three inches for each foot of ceiling height, so for a room with a standard 8-foot ceiling (3 x 8 = 24), choose a chandelier with an approximate height of 24 inches.

I grew up in the 90’s, back when thrift store shopping was considered alternative and grunge.  While I tooled around Goodwill listening to Nine Inch Nails on my Walkman, my more sophisticated friends were at the mall, looking adorable & stylish in the latest trend from The Limited.

But that was the 90’s.

Thrift-store shopping, dumpster-diving, and hand-me downs deliver a new parlance that has clever DIY’ers quaking with excitement for Saturday yard sales and obsessively scouring Craigslist for the Next Big Find.  This elegant new term for taking used items and making them new = REPURPOSING.

Also commonly referred to as recycling, upcycling, reinventing, revitalizing and/or reusing, entire boards are dedicated to this subject on Pinterest. Everything – and I mean everything – can be repurposed.  So why not the light bulb?

With a few basic tools and a steady hand, a light bulb can be hollowed out and transformed into a unique gift or decorative project.  Prepping the bulb, however, is not a task that we recommend for the kids.  Before you undertake any of these projects, take a moment to read a tutorial on how to safely hollow out a light bulb.

1. Witches Brew

By Clarissa Allison | December 2nd, 2016

When it comes to choosing which manufacturers to represent, several things are taken into consideration. Longevity, reputation, variety of selection, and response time are all paramount. This week LouieLighting.com would like to introduce a manufacturing partner we are proud to showcase: RAB Lighting.

RAB Lighting has been a leading manufacturer of sustainable indoor and outdoor lighting fixtures since 1946. Their reputation is grounded in the finest manufacturing, supported by a growing infrastructure complete with sophisticated facilities and engineering capabilities. Known for its cutting edge product design, quality, and customer support, the company operates the 6 acre corporate headquarters and manufacturing facilities in Northvale, New Jersey as well as locations in China, Taiwan and Malaysia, from where RAB is serving a constantly growing lighting market.

In 2002, RAB Lighting provided the Vaporproof fixtures which formed the Olympic Rings – this project resulted in the largest sign in history. What a feat! Accomplishments such as these demonstrate the pride and craftsmanship central to the brand.