There are times when you plug in the toaster or try and run the vacuum cleaner and it won’t work right. You probably unplug it and try it again and it works fine. You think nothing of it and assume it was a fluke—until it happens again with another appliance with the same outlet. Now, you have to wonder, is it an electrical problem or is it really just a fluke? These situations may appear to be no big deal on the surface, but they really are and can indicate there is something going on behind the outlet cover. Something like frayed or loose wires that could create a spark and start a fire that burns slowly and becomes a serious problem before you know it. You need an electrician in Beverly Hills to investigate these little problems before they become big ones that threaten your home and your safety. The team at The Electric Connection is here to help.

Outlets that work intermittently are just one of the symptoms of a serious electrical problem. Lights that flicker or do not turn on even when a new bulb is installed are another sign of electrical trouble. The light fixture may have wiring that has deteriorated or the wiring in the ceiling could be bad. Because you can’t tell simply be looking at the light or the light switch, you need to call an electrician familiar with Beverly Hills electrical needs.

The electrician will do an inspection and thoroughly investigate the problem. If it is a wiring issue to a single outlet or light fixture, it is a fairly easy fix. If you have a breaker that trips frequently, let an electrician know. This is another sign of a problem. Never leave little electrical problems unchecked. They can quickly become serious concerns. Give The Electric Connection a call today and schedule your electric inspection.

Electrical engineers usually have a huge responsibility in implementing safe electrical conduits to ensure safety and efficiency in designs of power substations. Conduits are the means in which power cables run from the ground to the electrical equipment and appliances. In addition, conduits provide protection of medium-voltage circuits in the power substation. Examples of circuits that need this protection are collector circuits entering the substation and distribution circuits leaving the substation to feed residential and commercial power needs.

Regardless of bends, twists, or turns, Example of a cut line on LED strip lights

2. You will now have two LED strip lights. Carefully peel back the end portion of the paper strip covering the strip’s adhesive backing, and then remove the 3M VHB adhesive from the solder pads on the bottom side of one of the strips. The strip with its adhesive peeled back will be the top strip when soldered.

5. Align the non-tinned strip segment (strip with adhesive removed) directly over the newly tinned pads, and apply heat. Hold the soldering iron in place until the solder remelts and begins to flow. To strengthen the bond and improve visual appeal, a small portion of solder can be added to the top pad.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split and solder a run of non-weatherproof two-conductor or connecting wires. Peel away the blue wire so that only the positive (red), negative (black), and control (green) wires are left.

*No wires should be peeled away if you’re joining single-color or standard RGB light strips.

3. Properly heat your soldering iron. For best results, clean and tin the tip of the iron immediately before soldering. To tin the iron, touch solder to both sides of the iron’s tip.

4. Next you will need to tin the solder pads on both ends of the split strip light. When soldering, always apply heat to the target area on the strip and not directly to the solder. Once sufficient heat has been applied to the area, start introducing solder.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split, solder, and reseal a

3. Follow steps two through five located at the top of this post for soldering a standard RGB strip light.

4. To reseal the strip light, apply

The LED strip lights are now connected, and power should flow through the entire length of the weatherproof strip.

More people have been thinking of trying to switch from oil-dependent vehicles to electric cars. However, many of the same individuals are also intimidated by the numbers of gas vs. charging stations available near them. While this might not be a problem in larger cities, more rural locations can run into charging issues. This is why charging your vehicle at home is so important. Around 88% of electric vehicle drivers refuel at home or at work.

Depending on your car, you might need different levels of charge. A level 1 charger uses wall sockets in the average home. However, 1 charge could take about 22 hours to complete. A level 2 charger is a little better. It works with a 240-volt wall outlet and can give you around 70 miles per charging hour. You can use the same outlet as your washer and dryer, but having a dedicated outlet for your car can help you prevent potential problems from alternating electricity flows.

A level 3 charger is the fastest and most efficient option for charging an electric car. Level 3 chargers, also called DC fast chargers, use a special charging port to get power to the battery while bypassing the car’s onboard charger. With this kind of station, you can fully charge your vehicle in a half hour.