When you are getting any electrical work done in your home, you want to make sure that the job gets done in the best possible way and that the best materials and workmanship are used in the work too. This is exactly why you conduct a certain amount of research online and try to zero-in on a credible and well-established company. However, this can sometimes be easier said than done and you may scour several sites and still not be sure which company you should contact for the work you need done.

We understand exactly how difficult this decision can be and so we have put together this list of things you should consider while choosing a residential electrician:

This isn’t very difficult to decipher. In Australia, when it comes to electrical jobs, the only things you are legally permitted to do are to change your light bulbs & operate the electrical appliances in your home, for what they were designed for. If you need any other electrical work done, beyond that; you would have to hire the services of a licensed and certified electrical contractor. This includes even the small things such as:

Even when you feel that certain jobs are very basic and that you will be able to tackle them yourself, keep in mind that electrical jobs are very risky and dangerous; and a single wrong step can cause an electrical fire and pose a risk to life and property. This is exactly why it’s important to hire the services of a credible electrical company.

They will work safely, use the latest and most advanced testing and work tools and ensure the work is done safely and in line with the applicable legislation in the state. In addition, the work has to be done as per the Australian Standard Wiring Rules. The electrician is also required to provide a certificate of compliance for the work they have handled for you.

In the current day, every state and territory requires that electricians should hold a valid electrical license to carry out any work. Most of the states also require that the electricians be R.E.C’s (Registered Electrical Contractors), before they are permitted to handle any electrical work or run an electrical contracting business.

For more information, simply speak with the experts at Allround Electrical and take their advice on various aspects of CBUS installations. The number to call is – 1300 169 263. You can also write to us at this email address. You may also reach us through this online contact form.

Thanks for reading,1300 169 263

Regardless of bends, twists, or turns, Example of a cut line on LED strip lights

2. You will now have two LED strip lights. Carefully peel back the end portion of the paper strip covering the strip’s adhesive backing, and then remove the 3M VHB adhesive from the solder pads on the bottom side of one of the strips. The strip with its adhesive peeled back will be the top strip when soldered.

5. Align the non-tinned strip segment (strip with adhesive removed) directly over the newly tinned pads, and apply heat. Hold the soldering iron in place until the solder remelts and begins to flow. To strengthen the bond and improve visual appeal, a small portion of solder can be added to the top pad.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split and solder a run of non-weatherproof two-conductor or connecting wires. Peel away the blue wire so that only the positive (red), negative (black), and control (green) wires are left.

*No wires should be peeled away if you’re joining single-color or standard RGB light strips.

3. Properly heat your soldering iron. For best results, clean and tin the tip of the iron immediately before soldering. To tin the iron, touch solder to both sides of the iron’s tip.

4. Next you will need to tin the solder pads on both ends of the split strip light. When soldering, always apply heat to the target area on the strip and not directly to the solder. Once sufficient heat has been applied to the area, start introducing solder.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split, solder, and reseal a

3. Follow steps two through five located at the top of this post for soldering a standard RGB strip light.

4. To reseal the strip light, apply

The LED strip lights are now connected, and power should flow through the entire length of the weatherproof strip.

There are so many things to love about the coming holiday season. Great food, great company, family, festive decorations; we couldn’t be more excited! But there’s a not so great factor attached to it all, too. That hefty electric bill you’ll be seeing. Looking for ways to keep your costs at a minimum this holiday? The expert electricians at Hoffman Electrical can provide some easy fixes!

Our professionals have been proudly serving Tampa and Clearwater, Florida for years now. When it comes to quality and top-tier service, we’re the name to know in electrical! And as  apart of our great service, we’re always looking for ways to help out. If you want to reduce your energy costs this season, we’ve got the solutions you’ll be happy to know.