If you’re dying to install your new instructions for how to install a light bar. These instructions include options for installations with or without a wire harness and for connecting to existing LED lights. Installation will vary based on the type of vehicle, existing lighting setup, and chosen wiring method, but these instructions can serve to give you a general idea of the process. Light bar mounting instructions are also available and are listed by WH-DTS10, WWH-DTD30; (ATP) WH-ATPD20, sdoptional mounting brackets; be sure not to overtighten the hardware (you will need to adjust it in step 7).

3. Route the lighting side of the wiring harness from the battery to the light in a safe, secure manner. Connect the harness to the light. Be sure to avoid heat sources and any moving parts while running your wires. Prolonged chafing of the wires may lead to a short in the circuit. Typically, following the vehicle manufacturer’s wiring harness is a safe path to follow. Some lights may not have DT or ATP connections on them, but the connectors can be added from the harness kit or purchased separately (ATP-FPT).

4. Continue to route the switch portion of the harness to the desired location of the switch. The switch may need to be unplugged from the harness to make routing of the harness easier. An optional remote-controlled switch (RS-x) are also available with different legends.

5. Connect the black (ground) wire with the large ring terminal from the harness to the negative battery terminal. Connect the red (power) wire with the large ring terminal from the harness to the positive battery terminal.

6. Secure the relay to a suitable location, and test the light to make sure the circuit works.

7. Finally, aim the light in the desired direction, and tighten all mounting hardware.

3. Connect the black ground wire of the new light to the ground wire of the old light with solder and heat shrink tubing (PSC-x). Connect the red power wire of the new light to the power wire of the old light.

4. If the new LED work light or off-road light bar has an ATP or DT connector that you wish to utilize, corresponding ATP (DT-MPT) pigtails are available.

5. Finally, aim the lights in the proper direction, and tighten all mounting hardware.

1. Find a suitable mounting location that will allow for running wires and mounting the LED light bar. Mark where your holes will be for the light bar brackets or mounting feet. Check behind drilling locations to ensure nothing will be damaged. Drill appropriate-sized holes.

2. Mount the lights with the provided hardware or with DT-MPT or RRS-SP, RRS-SPx, or RCS-RF25A) under your hood to speed up install time and avoid routing wires through your vehicle’s firewall. Route another run of red wire from the pigtail adapter (connected to the light) to the output terminal of the switch. Be sure to avoid heat sources and any moving parts while running your wires. Prolonged chafing of the wires may lead to a short in the circuit. Typically, following the vehicle manufacturer’s wire harness is a safe path to follow.

4. Be sure to double-check for all obstructions and proper clearance. Drill an appropriate sized hole for the switch, and mount it.

5. Connect your black wire to the negative battery terminal. Connect your red wire to the switch input terminal and to the positive battery terminal with an appropriate-sized fuse holder (MAF-x) installed within 18 inches of the battery. You will have to cut your section of red wire to allow for the fuse holder to be installed between the switch and battery. Connect your other run of red wire to the switch output terminal.

6. Finally, aim the lights in the proper direction and tighten all mounting hardware.

It is that time of year again! Spring is here and the flowers are starting to bloom as well as the trees. You are probably already dusting off your lawn furniture and getting ready for another season of mowing the lawn and trimming the hedges. Don’t forget to take a look at your landscape lighting as well. There are probably some lights that need replacing or maybe you are considering adding more lights or replacing your solar lights with electric lights. No matter what the case is, you will want to hire an electrician in Santa Monica to get the job done right. The team at The Electric Connection is ready to help you get your landscape lighting in tip top condition so you can be proud of your yard this summer.

Landscape lighting has come a long way in the last decade. There are so many different kinds of lights to choose from you are sure to find something that fits your personality and style. You don’t have to stick with the typical lantern-style lighting lining your walkway. Go bold and add a little flair to your landscaping by choosing lights that are a little different from the norm, but still just as effective. Once you have chosen your style of lights, call your Santa Monica electrician. You will want to make sure the lights are installed properly and will work throughout the season. Electric lights tend to be more reliable than their solar counterparts. They can also be placed in shady places under shrubs and on the shady side of the house.

Because there are some electrical wires associated with electric landscape lights, it is best to have the job completed by a professional electrician. Santa Monica homeowners will feel better knowing it was done right and their home’s safety has not been compromised by incorrect wiring. Give The Electric Connection a call today and schedule your landscape lighting install or upgrade.