RGB LED strip lights are a great way to add a pop of color to your above-ground pool. These low-voltage LED lights can be applied to the inside rim of your pool or around your pool deck. With RGB LED strip lights, you can choose from a ton of dynamic color-changing and single-color modes with adjustable brightness and speed control. They’re great for parties or late-night swims and can be easily installed. We’ve included installation instructions for our waterproof LED strip lights. Some cities require above-ground pool lighting to meet National Electrical Code (NEC) Article 680 standards, which would limit possible pool lighting installation locations. Before you purchase LED pool lights, check your city’s code requirements. We also recommend that you have a certified electrician install your lights.

1) Before ordering your LED strip lights, measure the diameter of your pool and multiply by 3.14 to find its circumference; this number indicates the total length of strip that you will need. The 21-foot pool used for these installation instructions has a circumference of 65.94 feet and requires 4 runs of 16-foot LED strips.

You will also need to measure the distance between where your power supply will be and both sides of your pool where the amplifiers will be installed (see the setup and wiring illustration below). These distances will tell you how much 18-gauge wire you’ll need for connecting the amplifiers to power. Make sure to account for the distance of any dips or turns that the wires may take along their paths.

Lastly, measure the approximate distance that will be between your controller and where your strip lights begin. This distance will tell you how much 22-gauge wire you’ll need for connecting the controller to your strips. You will also need two small sections of this wire for connecting your first and second strip lights to the amplifiers.

2) Before you’re ready to install your LED strip lights, be sure to drain your pool. Begin by creating or locating a dry area away from your pool for the power supply. The power supply should be contained in a weatherproof box. Power supplies should be installed between a ground fault circuit interrupter (GFCI) protected circuit and the pool’s junction box. It’s crucial to use a GFCI protected circuit as it shuts off if current flows where it’s not supposed to.

Wire the included plug to the power supply, but do not connect to power until the installation is complete.

3) Connect your RGB LED controller to the power supply. Cut the barrel off of the controller wiring. Strip back the remaining wires, and connect its wires to the power supply.

4) Cut the LC2 connector off of the remaining end of the controller, and strip back the wires. Run 22-gauge four-conductor wire to connect the controller to your low-voltage pool lights; use dolphin connectors to join like-colored wires. Connect your first two LED strip lights to the controller by joining each set of like-colored wire with a dolphin connector. You should be connecting four wires of each color (red, blue, green, and black) together. For added protection, cover all wire connections in this installation with electrical tape.

5) You will apply strip 1 clockwise around your pool rim and strip 2 counterclockwise. If you have a flat surface, use mounting clips to secure the strips in place as you go. If you want to mount the strips under your pool rim, drill small holes in the trusses approximately every 2 feet. Use cable ties to anchor the strip to the truss. You can also use speed nuts or cotter pins for strip anchoring to avoid drilling holes.

Solder a small section of 22-gauge four-conductor wire onto the strip’s end terminals. To reseal the LED pool light strip, slide wires through the holes of a 10-mm end cap, fill the cap with silicone, and slide it into place on the end of the strip. Be sure to cover all of the exposed conductive traces to ensure water resistance. Allow a minimum of two to three hours for the sealant to cure.

7) Once the new end wires are attached to the strip, you will mount the amplifier. Use the double-sided 3M foam pad to mount the amplifier in the middle of strip 1 and strip 3. For best results and added security, apply 3M adhesion promoter to the amplifier and its installation location on the pool wall.

8) Using a dolphin connector, join each like-colored wire on strip 1 to the same color on one end of the amplifier. Do the same when connecting strip 3 to the other side of the amplifier. You should be connecting three wires in each color (red, blue, and green) together on each side of the amplifier. The black strip wire will be joined with white amplifier wire. Note that the separate group of just black and red wires are meant to be connected to the power supply. Follow the same instructions for connecting strips 2 and 4 to the amplifier on the other side of the pool.

9) Use 18-gauge wire and dolphin connectors to connect the amplifiers to your power supply.

10) Plug the power supply’s attached cord into an outlet, and enjoy your LED pool lighting system! Refill your pool with water, but make sure to leave space between the water line and the lights.

For more LED pool lighting options, see our entire selection of waterproof color-changing LED strip lights.

For technical questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

The MD, DC, and VA area is known for getting slammed with violent and powerful thunderstorms that produce severe lightning. Electrical surges, which are caused by lightning, can wreak havoc on your expensive electronics and appliances.

A lightning strike that hits a power line several miles away from your house can impact all your electronic items. Whole-house surge protection is the best option you have to protect your home electronics and wiring from the damage caused by lightning strikes.

Everyone from the National Fire Protection Association to the Institute for Business and Home Safety recommends the use of whole-house surge protection. As a homeowner, the good news for you is that protection is readily available, and even top-of-the-line solutions are affordable. The gold standard in whole-house surge protection is a two-tiered system—a whole-house surge protective device, or SPD, installed at the circuit breaker box, and plug-in SPDs on individual outlets. A whole-house SPD can protect against up to 40,000 amps of current flowing into your home from the outside; normal household power is between 200 to 300 amps. When an electrical surge occurs as a result of a lightning strike, the device detects the excess current and safely diverts it through the house’s grounding path. Whole-house surge protection provides homeowners in MD, DC, and VA peace of mind when a powerful thunderstorm passes the area.

Whole-house surge protection can typically be installed in a home for around $200—it’s an easy job for a top electrician. The cost of replacing electronic equipment in an average home is a whopping $8,000, and it may be even higher for homes in MD, DC, and VA. Whole-house surge protection is cheap insurance against electrical surges caused by lightning strikes. It provides a layer of protection to all the electronic items in your home.

To ensure complete safety, Kolb Electric recommends that you allow a qualified, experienced electrician to complete the wiring for whole-house surge protection—there are several steps involved that are best left to a professional.

If you require surge protection wiring or want a full whole-house surge protection installation, contact Kolb Electric.

Anytime you call on contractors to perform work for you, you want to make sure you are choosing a company that is delivering the best service on the market and is improving your home or business. That is true for hiring solar installers as well. When you hire solar installers, screen potential companies for the following traits:

You can expect the Electric Connection to satisfy all these conditions. We’re the leading solar installers in the Los Angeles area and are ready to set you up with a solar system that saves energy and money while we redefine your notions of exemplary contractors. Call us to start on the road to energy savings!

If you have just recently purchased a home or have concerns about the home you currently live in, you can call to have an electrical safety inspection. These inspections are performed by a knowledgeable electrician who can identify any potential hazards you may have in your home. It is always a good idea to have an inspection upon moving into a new home. It essentially gives you a peek behind the walls so you know exactly what you are getting into.

These inspections will need to be performed by an electrician. Pasadena residents can call The Electric Connection to have one of these assessments performed. If your home is older or if you have noticed some issues like tripping breakers, flickering lights or dead outlets, it is crucial you have an electrician come out. The electrician will also be looking for outdated electrical work that should be replaced to meet today’s current standards. Over the years, technology has given us safer methods of bringing electricity into our homes. You will feel safer knowing your home is up to code and as safe as possible.

There are some serious hazards that can be lurking in the walls that could end up starting a fire if left unchecked. These hazards may go unnoticed until it is too late. In many cases, there are some warning signs like the ones mentioned above and in other situations the problem goes undetected until it is too late.

During an inspection, the electrician will evaluate the home’s wiring for fraying or breaking along the line. The entire process is relatively short and inexpensive. Once the inspection is complete, you will get a report from your electrician. Pasadena homeowners will rest easy once they know the condition of their home’s wiring. Any problems that have been identified should always be fixed immediately. This is something The Electric Connection can help you take care of. Just give us a call today.