There are several new models of electric powered cars becoming available as well as others in development.  These electric powered vehicles are the wave of the future.  But, right now, they are expensive (the cost upfront is still significantly higher than their combustion engine counterparts), and there are certain qualities about them that still make people a little bit hesitant to make the switch to a car that needs a charger rather than a tank full of gasoline.

No one can argue that these vehicles offer some significant advantages over cars that run on gasoline, which should seriously be considered high selling points if you’re considering buying an electric car in the near future.  They have the ability to significantly reduce air pollution in metropolitan areas because they have zero tail pipe emissions.  They also have the ability to help decrease our incredible dependency on oil.  It also turns out that electric motors are much more efficient than internal combustible engines – the amount of energy lost in the process of converting electricity into usable motor power is much less in an electric engine than in the standard engine.

Some of the problems that these electrical cars have had in the past (and still make people nervous) have been overcome or are in the process of being overcome.  Initially, the small motors meant slow acceleration.  However, the current electric motors really don’t accelerate significantly slower than other motors.  The batteries that these cars use have also evolved over time and now offer a much better range than early models.

The issues of range anxiety and worrying about charging your car more often than is really convenient most likely won’t disappear completely until there are enough people out there driving electric cars to prove that charging them is no more inconvenient than having to stop at a gas station to fill up regularly, but these are the cars of the future, and the future is closer than most people realize.

What are your thoughts? Post a comment or share on our Facebook Page

relatively high ceilings. Drive by any industrial park, warehouse, or factory, and walk inside and what you will see is a high bay light.

But walk into any factory or warehouse and you will see different styles and options, wattage’s and configurations. Traditional high bay fixtures that were once common place were Mercury Vapor, which were then replaced with High Pressure Sodium and Metal Halide bulbs. As new technologies were introduced, and old technologies became more common, the old HID bulbs were replaced with Induction and Fluorescent light sources. And more recently with the more wide spread approval and popularity of LED, we started to see conversions from these older technologies to the latest energy saving LED High Bays.

A High Bay Fixture, depending on the light source, can take on many forms and shapes. If you consider a Metal Halide or High Pressure Sodium fixture, they typically consist of a large heat sink block at the top of the fixture that typically houses the fixtures ballast. Below is an aluminum or acrylic dome and at the top of the dome is the HID bulb. These bulbs typically come in two wattage’s, 400 and 1000. 400 Watt Fixtures tend to be installed in ceiling heights no higher than 30 feet, 1000 watt fixtures are typically 40 feet or higher. Interestingly enough, spacing of lights is similar to the height they are located off the floor. A fixture installed at 20 feet from the floor is installed in a 20X20 pattern, 30 feet in a 30X30 pattern, 40 feet in a 40X40 pattern. Of the 3 type of HID bulbs, Metal Halide tends to be the best option. High Pressure Sodium Bulbs are very low on the temperature color and have the warehouse aisles have the ability to focus the light where it is needed. A light designed for a warehouse aisle is a lot different than a light designed for a gymnasium or a factory floor. In these spaces, a light that can flood the area evenly is important, in a warehouse aisle, a light that can light up the face of the shelves and the floor below is important. And when selecting energy efficient options, its just as important to understand the technology and what it is capable of doing. Adding controls to a T5 fluorescent fixture is a good idea only if the ballast is designed to handle that requirement and not lower the life expectancy of the bulbs. Motions sensors and daylight controls that dim the light output based on occupants and the amount of daylight available in the space. Technologies such as metal halide and high pressure sodium are not a good choice as these technologies are not good at dimming or turn on or off quickly. Fluorescent can dim, but you need special ballasts for them. So knowing what you want to do and may want to do is important at time of purchase, because not having the proper equipment or options could mean a costly lighting warehouses, factories, gyms and readily available through the utility companies, and mass adoption means the technology of LED had matured to the point where the questions and disbelief of past years have gone away.

When is it Time to Upgrade Your Electrical Work?

You can't see the electrical wiring in your home, but it’s integral to your day-to-day life. The electrical work behind your walls is responsible for lighting your home, powering your microwave and electric stove, running the air conditioning and so much more. So while your electrical work might be out of sight and out of mind, you'll definitely notice if something goes wrong. That's why you should prevent electrical problems before they start by evaluating your wiring and planning upgrades if your system turns out to be damaged, out-of-date, dangerous or otherwise not up to the standard required for modern homes.

Update Outdated or Dangerous Wiring

There are a number of reasons why your electrical work could be in need of an update. One of the most important, and potentially most expensive, is if you have an outdated wiring system running through your home. Homes built in the 1970s or earlier could have aluminum wiring, or even worse, knob and tube wiring – neither of which was designed to carry the amount of electricity necessary for today's households. If you have one of these systems in your home, you might be able to increase your home’s electrical capacity and improve its safety by replacing that infrastructure with modern copper wiring.

Even if you have a modern wiring system, problems like corrosion or damaged wiring may be undetected and worsening. That's a serious hazard hidden in your walls that you might not know about until it's too late. There could also be other dangers in your electrical work, like shoddy connections in your circuit box, too many outlets on a circuit, or a lack of proper grounding.

Look for Expert Guidance

If your electrical work seems like it's performing fine for now, that doesn’t mean there’s no reason to check it out. First and foremost, old wiring puts you at increased risk of an electric fire, which is a risk to both your property and your life. Furthermore, many home insurance agencies won't issue you coverage, or will charge increased premiums, if there is outdated electrical work. Old wiring also may not be up to your municipality's current local building code. Although existing homes are generally grandfathered into compliance if they don't meet new standards, you may be required to make updates to bring the system up to code if you perform any electrical work on your home in the future.

Properly evaluating the safety of a home electrical system is beyond the ability of most homeowners, let alone performing major upgrades like rewiring the home. If you have any doubts about the age or status of your home electrical work, call a qualified electrician today to advise you and make any necessary updates or repairs.

Whether you’re planning a week-long vacation or a short weekend getaway for Labor Day, you’re going to want to safeguard your home against potential break-ins. Of course, the hope is always that nothing bad will happen while you’re away, however, if we’ve all learned something it’s that preparedness is key. We all have our own methods for deterring burglars, but in the end the goal is always the same: make it appear as if there is activity both inside and outside the home.

We’ve put together a list of what we believe to be the most useful home safety tips. It’s always helpful to plan ahead of time rather than on the day of. When you put together a plan in advance, we guarantee you it will be more thorough and you’ll feel much better about leaving your home.

Ask a friend or neighbor to keep watch