If you’re dying to install your new instructions for how to install a light bar. These instructions include options for installations with or without a wire harness and for connecting to existing LED lights. Installation will vary based on the type of vehicle, existing lighting setup, and chosen wiring method, but these instructions can serve to give you a general idea of the process. Light bar mounting instructions are also available and are listed by WH-DTS10, WWH-DTD30; (ATP) WH-ATPD20, sdoptional mounting brackets; be sure not to overtighten the hardware (you will need to adjust it in step 7).

3. Route the lighting side of the wiring harness from the battery to the light in a safe, secure manner. Connect the harness to the light. Be sure to avoid heat sources and any moving parts while running your wires. Prolonged chafing of the wires may lead to a short in the circuit. Typically, following the vehicle manufacturer’s wiring harness is a safe path to follow. Some lights may not have DT or ATP connections on them, but the connectors can be added from the harness kit or purchased separately (ATP-FPT).

4. Continue to route the switch portion of the harness to the desired location of the switch. The switch may need to be unplugged from the harness to make routing of the harness easier. An optional remote-controlled switch (RS-x) are also available with different legends.

5. Connect the black (ground) wire with the large ring terminal from the harness to the negative battery terminal. Connect the red (power) wire with the large ring terminal from the harness to the positive battery terminal.

6. Secure the relay to a suitable location, and test the light to make sure the circuit works.

7. Finally, aim the light in the desired direction, and tighten all mounting hardware.

3. Connect the black ground wire of the new light to the ground wire of the old light with solder and heat shrink tubing (PSC-x). Connect the red power wire of the new light to the power wire of the old light.

4. If the new LED work light or off-road light bar has an ATP or DT connector that you wish to utilize, corresponding ATP (DT-MPT) pigtails are available.

5. Finally, aim the lights in the proper direction, and tighten all mounting hardware.

1. Find a suitable mounting location that will allow for running wires and mounting the LED light bar. Mark where your holes will be for the light bar brackets or mounting feet. Check behind drilling locations to ensure nothing will be damaged. Drill appropriate-sized holes.

2. Mount the lights with the provided hardware or with DT-MPT or RRS-SP, RRS-SPx, or RCS-RF25A) under your hood to speed up install time and avoid routing wires through your vehicle’s firewall. Route another run of red wire from the pigtail adapter (connected to the light) to the output terminal of the switch. Be sure to avoid heat sources and any moving parts while running your wires. Prolonged chafing of the wires may lead to a short in the circuit. Typically, following the vehicle manufacturer’s wire harness is a safe path to follow.

4. Be sure to double-check for all obstructions and proper clearance. Drill an appropriate sized hole for the switch, and mount it.

5. Connect your black wire to the negative battery terminal. Connect your red wire to the switch input terminal and to the positive battery terminal with an appropriate-sized fuse holder (MAF-x) installed within 18 inches of the battery. You will have to cut your section of red wire to allow for the fuse holder to be installed between the switch and battery. Connect your other run of red wire to the switch output terminal.

6. Finally, aim the lights in the proper direction and tighten all mounting hardware.

]]>

Piano Lamps Sing and Make Sweet Music at Capitol Lighting!

Ambient lighting in a piano room or formal living space is the key note needed and piano lamps can make this room sing and make sweet music!  Capitol Lighting offers a beautiful selection of piano lamps and picture lighting for any room in your home. Make a grand statement with modern piano lamps on your baby grand piano! House of Troy lighting makes any piano sing and they offer picture lighting in a wide selection of finishes to choose from such as polished brass-gold, black and even satin nickel brushed steel.

Create the perfect ambient lighting in your formal living room or piano room with House of Troy lighting.  Piano lamps and picture lighting is the key note needed to create a soft and inviting glow in a formal space.  Shop Capitol Lighting online for all of your formal lighting needs and start creating sweet music with House of Troy lighting.

When it comes to fixing the electrical work in your Florida home, most homeowners who jump into the DIY pool do so for two main reasons. One, of course, is for the thrill of victory, so to speak. The other, and more obvious reason, is for the cost savings. The majority falls into the second category, but the results are often just the opposite.

Well-meaning homeowners often end up spending nearly double of what they budgeted due to poor planning, lack of knowledge, and costly mistakes.