efficiently as possible. Your attic fan can be installed one of two ways, either gable mounted or roof mounted, and is controlled by an automatic thermostat that shuts it off or turns it on.

An attic fan will perform as effectively as it should in a properly sealed and insulated attic, so that no heat or moist air can sneak its way in. This helps with your HVAC efficiency, and also protects your roof and your attic’s structure.

Your attic fan serves as a way to efficiently ventilate the space, but it is so much more than that, too. As we stated above, the temperature in your attic can be far above the outdoor temperatures. This is if you do not have an attic fan installed. Regular vents do allow for some cooling, but not to an extent that you’ll notice the difference.

A properly installed and serviced attic fan can help drop your attic temperatures by as much as 50 degrees, making your entire house cooler. This means you’ll be able to turn up your air conditioner’s thermostat by as much as 10 degrees, but still remain comfortable.

In the wintertime, moisture can quickly turn to ice or frost, and as that expands in can damage your roof and the structural integrity of your attic. An attic fan, however, can fend off the moisture before it is able to damage your roof in this manner.

Ice is not the only danger that moisture brings, either. When moisture cannot be ventilated and is left to sit, mold can start growing. Unfortunately it’s very easy for moisture to reach your attic—even your showering and cooking allows this to happen. But an attic fan can resolve this problem.

Your air conditioner will not have to work so hard to do its job when it is assisted by an attic fan. Also, it’s likely to last a lot longer—given that you schedule regular maintenance—when you don’t have to run it as often. Repairs will happen from time to time, but an efficiently working AC system is a lot less likely to give you problems than one that doesn’t have the assistance of an attic fan.

Being prepared for anything is nearly impossible, but you can be prepared for some of the little eventualities in life like a power outage. If you are prepared for the outage it is a lot less inconvenient than if you were taken completely off guard. Power outages happen for numerous reasons. Most of the time the outages are not long in duration, but there are times the outages can be extensive and your life is sorely interrupted. An electrician in Santa Monica has some advice for you to follow before an outage happens so you can be ready to deal with the aftermath. At The Electric Connection, you will find a team of knowledgeable electricians who can provide you with service to deal with any electrical problems caused by an outage. There are times appliances malfunction after a power outage. You can prevent this from happening by having a whole home surge protector installed.

You can also prepare for the lack of lights by putting a couple of flashlights along with extra batteries in a safe place that you can easily find when the lights are off. A kitchen drawer, a nightstand table or near the front door are all good places. Along with flashlights you will want to have a supply of emergency candles along with matches or a lighter. Don’t forget to keep candleholders handy as well. If you are not comfortable with using candles or relying on flashlights, you can talk with a Santa Monica electrician about installing a standby generator.

Keep the phone number of the power company handy as well. Most power companies will have an emergency number. This is the number you would call to find out how long the outage will last. If you have any more questions or would like to learn more about generators or surge protectors, give The Electric Connection a call today.

We often forget how important it can be to call an electrician if a problem arises with a home’s electrical system. In fact, most homeowners are complacent that their wiring system is just fine and needs no care or maintenance. More often than not, the only time a licensed electrician is called to a house when something is going wrong. It’s important to understand how to recognize when you may need to be preemptive about electrical problems and subtle signs that your electrical system needs maintenance or repairs. Keep an eye out for the following issues that could arise, indicating a bigger electrical problem in your home.

If you’re a fan of power strips, that’s not necessarily a problem right away. The problem happens when you start to overload a specific circuit in your home. Attaching a power strip and then packing it full of energy-heavy devices can quickly cause circuit breakers to flip. In addition to that risk, they can quickly become a fire risk when used inappropriately. Opt for power strips with surge protectors and be careful concerning how much you plug into them. If you need more outlet availability in a space, that’s when you need to call a local electrician.

While the rugs themselves aren’t a sign of electrical problems, the wires and cords run under them are. More and more people are adapting older homes to their current needs, leaving exposed cords and cables throughout the house. You don’t need to run them under carpet and rugs. In fact, that can be a tripping hazard. An electrician can quickly run wires and cables through the walls to get the cables out of sight and out of mind.

If you own an older home, you may have noticed how your outlets don’t look quite like outlets in newer homes. For a long time, two prong outlets were the standard. No many appliances use a three prong plug style in order to provide a ground for the electricity. Don’t be someone who just cuts the third prong off of their appliances or bends it back to make it fit in the two prong outlet; upgrade your outlets instead. Properly grounded outlets can reduce the risk of electrical fires and other risks due to electricity.

It’s important to regularly check your home’s main service panel. Regular visual checks and professional checks by an electrician can help to prolong the life of the panel and help avert any problems from improper care. When you visually inspect the panel, check for any signs of problems, including potential rust. If your panel is rusting, it’s time to have an electrician install a new one for safety and performance.

If you’ve ever turned on a light switch and found that the plate was warm to the touch, then you should call an electrician. Points where power is utilized in the wall should never be warm, and definitely not hot. It’s a sign of a bigger electrical problem that could be a safety hazard.

Aluminum LED profile housings allow you to create customized light fixtures with LED strip lights. Our Klus brand LED channels are available in many different styles, including recessed-, or flexible, O-shaped, and more. Available in 1- and 2-meter lengths, the channels can be easily cut for any application from under-cabinet lighting and bookshelf lighting to showcase lighting and transition strip lighting. They’re available with a variety of lens options, such as clear, frosted, and etched that complete the profiles. We’ve put together a step-by-step guide for using these channels to create your own light fixtures. Please note that your specific channel might vary from the one used in this tutorial.

Materials needed:

1. With a pair of clippers, carefully clip through the clear plastic heat shrink as shown in figures A-C. You will want to take your time and be careful not to cut the strip’s wires while removing it.

2. Lay the LED strip into the channel, and position it along the bottom so that the ends of the strip and the channel are lined up (fig. A). Now, remove the paper from the strip’s adhesive backing (fig. B), and adhere the strip to the LED channel—starting at the lined end and working your way to the other end of the strip. Be sure to leave roughly 1/4-inch free at the end of the channel so that you can install the end cap as shown in figure C.

3. If one of your end caps doesn’t come with a pre-drilled hole, you will need to drill your own to allow the wires of the LED strip light to come through. In this case, we used a Dremel tool, but other options are viable as well. Regardless of the tool you choose, it is helpful to mark the end cap where you would like the wires to come through. Start the hole small, and increase the size as necessary.

4. Place the end cap on the wired side of the strip by threading the wires through the end cap as shown in figure A. Insert the end cap into the end of the light bar, and push firmly until it is fully in place (fig. B).

5. On the open end of the bar, slightly peel up the end of the LED strip (fig. A); this is necessary to install the end cap. Now measure your channel lens, and trim off the excess with clippers (fig. B). Be careful when trimming to avoid cracking the plastic. Excess material can be lightly sanded off. Once the lens has been cut to the proper length, slide it into the channel, and install the end cap as shown in figures C and D.

6. That’s it! Your customized LED light fixture is complete and ready for installation, which we will cover in the next step.

7. Mounting this LED profile is as easy as applying double-sided tape to the back of it and sticking it to your intended surface. Be sure to cut the tape to fit the back of the LED profile and to leave the tape backing on the side not attached to the channel until you are ready to mount it.

For most LED profiles, mounting clips are available for a more permanent installation.

If you have questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.