It is estimated that thousands of electric shock accidents take place each year, of which some are fatal ones. Aside from this, there are incidents of electrical fires caused by poorly-installed or ill-maintained wiring. It’s important to understand that most of these fires and accidents are avoidable. There are some simple things you can do to prevent an electrical fire from erupting on your property, including:

Never try to force plugs into the outlets and don’t remove the third prong which is the grounding pin, to fit it a plug into an outlet with 2 prongs. Do not plug in too many appliances into a multi-plug outlet.

Check whether there are any loose-fitting plugs as these can be a fire/shock hazard. If you notice that any of the wall plates are broken/missing, replace them without delay. So that the components and wiring aren’t exposed. If you have very young kids in your home, make sure that you cover all used outlets.

Check the cords for fraying or cracks. Pay special attention to ones that are placed in any high traffic areas or under rugs and carpets.

Make sure that the wattage of the bulbs is compatible with the fixture requirements. If you find any bulbs with a higher-than-recommended wattage rating, replace them immediately. It’s also important to ensure they don’t overheat and that they are screwed-in securely.

These should never be used on a permanent basis. Use ones that have safety enclosures to protect kids from burn injuries and shock.

There should be GFCIs installed in the kitchen, bathrooms, garage, basement and various other indoor and outdoor outlets in your home. Test these on a monthly basis to ensure they are working as required.

Only older properties have fuse boxes and these don’t have the capacity to withstand the heavy electrical loads required by modern-day equipment and appliances. It’s far better to get these older systems evaluated by a skilled electrician and replace them with modern circuit breakers.

Faulty or old wiring is one of the commonest causes of residential electrical fires in Australia. Get these checked periodically for loose connections, loose wall fixtures or wall receptacles. If you hear any hissing, sizzling or popping sounds behind walls or from sockets, call in your local electrician without delay to get these installations inspected and replaced. If you find that any switches or electrical fixtures are hot to the touch, get those checked as well. Flickering light bulbs are another indication of problems in the electrical wiring as well and it’s best to get a thorough check conducted.

If you find that a specific circuit breaker trips repeatedly, or you experience shock when you touch it, you should unplug it immediately and get it replaced or repaired. Check for damage or cracks in the connectors and wiring and install surge protectors to protect all your expensive electronics.

When you upgrade your home, make additions or add extensions like extra rooms or an extra storey etc., or even add a large number of new equipment or electrical appliances to your home, that can overburden the existing electrical installations. At this point you would have to increase the service capacity of your home’s electrical system.

We are a company that has been operating in this space for a number of years and have the skill, knowledge as well as the resources to install, maintain and upgrade all types of electrical installations on your residential or commercial premises. For more information, contact the Allround Electrical team at this number – 1300 169 263. Alternatively, you can write to us at our email address.

Thanks for reading,1300 169 263

If you find yourself making that frustrating trip to the circuit breaker often enough to remember, there’s a good chance your electrical panel is overworking itself. An outdated electrical panel is a hassle no homeowner should have to put with. It’s not just an issue of faulty outlets and tripping over extension cords. An outdated electrical panel is a serious fire hazard.

It’s outdated for one, and that can cause a lot of problems, especially for any home improvement projects. An electrical panel’s job is to determine how much electricity is distributed to all appliances, lights, and outlets in your home. If your electrical panel is outdated, not only is it unfit to meet your electrical needs, it puts you and your home at risk. An up-to-date electrical panel has a circuit breaker, which trips or turns off when the wiring is overworked; this prevents your electrical system from overheating and starting a fire. An outdated electrical panel isn’t only a fire hazard; it’s harmful for the following reasons.

If your home needs an electrical upgrade, it can be as simple as replacing a few circuit breakers or replacing the entire electrical panel. It’s best to contact an electrical technician as the wiring in your home is a complicated mess, and a professional knows what to look for. They can inspect your home and provide the best suggestions on how to upgrade your electrical system.

If you live in the United States, you’re likely well-familiar with our typical wall-socket setup. Your plug has two flat pieces of metal roughly half of an inch wide, with one side sometimes being slightly wider than the other. Your wall socket has two slots that match this, with one side also being slightly larger than the other. However, sometimes there’s a variance: some plugs have a third prong below and between the normal two, and most electrical sockets also have a third hole to match this plug. What’s the difference between these two types of plugs and is one better than the other?

To put it simply, yes, one is better than the other. When it comes to electrical plugs, the old adage “less is more” does not apply—the three-prong plug is far better than a two-prong. To learn why, let’s discuss the difference between the two.

In order for electricity to flow, you must complete a circuit. A circuit essentially is a connection from your power source to the device, and then from the device back to the power source. The line that brings power from the power source to the device is called your “hot wire”, which is most often red and comes off the positive terminal (noted by the large “+” sign). The line that then returns from the device to the terminal, usually a black wire connected to a “-“ sign, is known as the “neutral wire.” A plug must have both of these lines in order to work.

However, the third prong in a three-prong plug is a “ground” plug, which dramatically improves safety. When an unexpected burst of electricity happens, such a short in the device or a surge from your power supply, the ground plug will take that abundance of additional electricity and move it away from the device and down into the ground where it is safe. This prevents your device from being overloaded which can cause overheating, sparking, and fires in addition to ruining it.

Three-prong plugs didn’t become the standard in homes in North America until the late 1960s. If you have a home that was constructed around this time or after, odds are your wall sockets are probably already of the three-prong variety. Two-prong plugs can work with three-prong sockets just fine, and you’ll rarely experience any issues.

However, if you have any old two-prong plugs, you’ll likely need your electrical system updated in order to upgrade to a three-prong setup. Properly installing ground wires can involve several hours of electrical work and even cutting into your walls in order to do so properly, so it’s a rather large undertaking. However, it’s by far the safest and most prudent option.

Another option that doesn’t involve tearing open your walls is to install a ground fault circuit interrupter outlet, otherwise known as a GFCI. These sockets are two-pronged, but feature a miniature circuit breaker that measures the resistance through a plug and mechanically shuts off when the risk of a shock is present. While this can help you avoid being shocked by a faulty device, there is still no ground wire present so your electronics are not protected from a power surge.