The weather outside bas been quite hot as the temperature has been reaching and exceeding the 30’s lately. Your electrical bill is probably rising with the temperature as well. Now is the time that many people start visiting stores in search of an air conditioning unit. This is a great way to cool down your home, but if your home’s electrical system is not prepared for the electrical load or you purchase the wrong unit, you could be left sweating more money than you expected.

Window-mounted air conditioning units are quite common to see in bedrooms or living rooms. These can be purchased from any local home appliance store. These units are mounted in the window and secured. These units pump in cold air and exhaust hot air to the outside – great for rooms that are frequented and difficult to keep cool.

The small units can also be purchased from your local appliance store. These smaller units cannot cool the same amount of area as a window-mounted unit, but can do the trick for small areas that you want to keep cool. The advantage of these is that you can move them from room to room quickly with little setup and takedown. One disadvantage of these units is that they tend to be quite noisy.

You may be fortunate enough to have one of these installed in your home. Central air units can be connected by ducts throughout the house and regulate the temperature set in the home. A central air unit is great for getting a consistently cool temperature in any room in the home while also keeping the noise to a minimum. One trick when it comes to central air is to ensure that you get a unit that matches the square footage for your home. If your air conditioning unit is too large for your home it may not properly dehumidify your home and run on short cycles.

When purchasing an A/C unit you want to ensure that you have a timer and energy-saver option. This will help keep your monthly electrical bills down. Energy efficient units will use less electricity and timer options can prevent the units from running when they are not needed. You also want to make sure that the unit is the appropriate size for your room or home. If the unit is too large it will cycle off quickly and can freeze air moisture without removing it, which can lead to a higher electrical bill.

If you are in the market for a new air conditioning unit for your home, make sure you do adequate research to ensure you are purchasing the right unit at the right size. Read the package for the required voltage and wattage. If you are adding an A/C unit in your home you could overload electrical circuits that are no prepared. If you have questions about your home’s electrical efficiency in the summer, call Expert Electric at 604-681-8338.

A frayed refrigerator plug can easily be classified as a very serious risk, both to the fridge itself, and to your entire home. Frayed, ripped, or otherwise damaged cords are a potential source of electrical fire, arcing and power failure. So, what do you do when you discover a frayed plug on your appliances?

Put simply, get it repaired! Often, replacements are available, but are very costly, and occasionally entirely unavailable depending on the age and model of your fridge.

We never endorse “Do It Yourself” solutions to any electrical issues, as electricity is fickle and extremely dangerous. A wrong move can cost you more than a busted appliance, it can cost you your health (or some serious money in fire damage repair to your home). Leave electrical work to Kolb Electric electricians! That said, we do believe in informed consumers, and thus have detailed our professional process for frayed or damaged plug repair.

Too often we encounter electrical incidents at home that could have been avoided with proper precaution and a timely replacement or repair. Don’t allow your home to harbor risks by leaving damaged plugs alone! Leaving damage untreated can lead to:

To address frayed, or damaged plugs we:

Be ready for any eventuality with our electrical repair services! Contact our experts today to learn more about our electrical services, or to schedule an appointment.

Perhaps you've always wondered what's in the mysterious metal box on the basement wall. It's a circuit breaker box, and without it your whole home electric system would be unsafe, leaving you in danger.

Circuit box repairs or upgrades require an expert, but you don't need to be a master electrician to understand the basics of how it functions. The most common problem is a tripped circuit, and you can usually reset it yourself.

What's in the Box?

The circuit box is frequently found in the basement, although it could also be in a garage, closet, utility room or even outside. All the electricity coming into your house flows through the box.

If you open the metal door, you see a bank of switches. Each one corresponds roughly to a room in the house, while certain outlets for major appliances like the washer or furnace probably have their own switch. They should be labeled.

There also may be a main disconnect breaker, usually at the top of the box, which allows you to cut off power to the entire house. In many newer homes the main disconnect may be outside near the electric meter. Some homes do not even have one. This is useful if you are doing electrical work in your house, or in the circuit box itself. The switch should be labeled “main” or something similar.

How It Works

Why do you need a circuit box? When an electrical device malfunctions, such as the motor in your freezer overheating, wires can get crossed, creating a huge spike in electric charge. That puts you at risk of overloading your electrical system, and unchecked overloads can cause lead excess heat stress on wires, or worse.

Fortunately, your circuit breakers are on the job. There is an electromagnet or bimetallic strip inside each breaker. If the current moving through the circuit gets too high the device flips a switch, disconnecting the circuit. No more electricity can flow to the part of your home where the problem is, so the danger is averted.

So if the power goes off in one part of your house but still works in the rest, a tripped circuit breaker is the most likely culprit. The switches in your electrical panel should be labeled; if not you can still tell which one got tripped, because it will be flipped part way toward the off position. Some switches also show red when they've been tripped.

How Do I Fix It?

All you have to do to restore power is flip the switch all the way to the off position, then back to on. If flipping the circuit back on doesn't solve the problem, it might be something more serious. In that case, it's time to call a licensed electrician.

Some newer circuit breakers have advanced features, such as the ability to detect when a person makes contact with a live wire and automatically cut off the current, potentially preventing injury or death by electrocution.

If you live in an older home you may still have a fuse box. It operates on the same principle as a circuit box, with one major difference -- the wire inside the fuse actually burns up if too much current passes through it, so if the fuse blows, you need to replace it. Most fuse-style panel are maxed out, so if you have one it would be a good idea to consult your electrician and see if it’s time to consider a replacement.

Need Some Professional Guidance?

Your local Mister Sparky® electricians are always here to help. If you're having problems with your circuit breakers or fuse box, give us a call.