1.  Size and install smartly:  Whether you are installing a crystal chandelier over your dining room table or as a central design feature in your master bedroom, the diameter and height of your fixture must be in proportion to other items in the room.  The diameter of a dining table fixture should be 12 inches less than the diameter of the dining table.  The height of the chandelier should allow for a clearance of 30 inches from table top to the bottom of the fixture.

Quoizel’s “Tricia” chandelier adds elegance to this contemporary dining room.  * Interior design by Sandra D’Amata International, Inc.

If your crystal chandelier will be a central focal point in your foyer, living room or master bedroom, take into account your ceiling height and choose a chandelier that may be installed to leave at least a 7-foot clearance from the floor to the bottom of the chandelier.

2.  Reflect Resplendence:  The true beauty in a crystal chandelier extends far past the light source, decorative finishing and crystal configuration.  Crystal facets reflect and refract a brilliant array of colors and illuminating effects, especially when combined with sunlight and/or electric light sources.  Matte finishes on furniture and surrounding walls work well with crystal illumination.  Avoid creating glare and unflattering shadows off metallic or shiny surfaces.

3.  Choose the Right Bulb: Most chandelier bulbs will be candelabra-based, yet what type of candelabra bulb you choose will make a tremendous difference in both the total presentation of your chandelier and the overall illumination in your room.

Crystorama’s “Mercer” chandelier–installed with dimmable LED candelabra bulbs–provides magnificent illumination in this master bathroom.*

Frosted bulbs provide a more subdued illumination. They are recommended for most traditional dining room chandeliers.  Clear bulbs work well with chrome finished retro-modern chandeliers and may add to the radiant sparkle of modern crystal chandeliers.

For a more traditional look, flame tip bulbs are the right choice.  Flame tip bulbs also look best in chandeliers with faux drip-candle holders.  Torpedo bulbs are less tapered and present a contemporary look.  Round bulbs add an eclectic vibe to a traditional chandelier.  Uniquely-shaped and/or textured candelabra bulbs may add a custom-designed artistry to your chandelier.

RGB LED strip lights are a great way to add a pop of color to your above-ground pool. These low-voltage LED lights can be applied to the inside rim of your pool or around your pool deck. With RGB LED strip lights, you can choose from a ton of dynamic color-changing and single-color modes with adjustable brightness and speed control. They’re great for parties or late-night swims and can be easily installed. We’ve included installation instructions for our waterproof LED strip lights. Some cities require above-ground pool lighting to meet National Electrical Code (NEC) Article 680 standards, which would limit possible pool lighting installation locations. Before you purchase LED pool lights, check your city’s code requirements. We also recommend that you have a certified electrician install your lights.

1) Before ordering your LED strip lights, measure the diameter of your pool and multiply by 3.14 to find its circumference; this number indicates the total length of strip that you will need. The 21-foot pool used for these installation instructions has a circumference of 65.94 feet and requires 4 runs of 16-foot LED strips.

You will also need to measure the distance between where your power supply will be and both sides of your pool where the amplifiers will be installed (see the setup and wiring illustration below). These distances will tell you how much 18-gauge wire you’ll need for connecting the amplifiers to power. Make sure to account for the distance of any dips or turns that the wires may take along their paths.

Lastly, measure the approximate distance that will be between your controller and where your strip lights begin. This distance will tell you how much 22-gauge wire you’ll need for connecting the controller to your strips. You will also need two small sections of this wire for connecting your first and second strip lights to the amplifiers.

2) Before you’re ready to install your LED strip lights, be sure to drain your pool. Begin by creating or locating a dry area away from your pool for the power supply. The power supply should be contained in a weatherproof box. Power supplies should be installed between a ground fault circuit interrupter (GFCI) protected circuit and the pool’s junction box. It’s crucial to use a GFCI protected circuit as it shuts off if current flows where it’s not supposed to.

Wire the included plug to the power supply, but do not connect to power until the installation is complete.

3) Connect your RGB LED controller to the power supply. Cut the barrel off of the controller wiring. Strip back the remaining wires, and connect its wires to the power supply.

4) Cut the LC2 connector off of the remaining end of the controller, and strip back the wires. Run 22-gauge four-conductor wire to connect the controller to your low-voltage pool lights; use dolphin connectors to join like-colored wires. Connect your first two LED strip lights to the controller by joining each set of like-colored wire with a dolphin connector. You should be connecting four wires of each color (red, blue, green, and black) together. For added protection, cover all wire connections in this installation with electrical tape.

5) You will apply strip 1 clockwise around your pool rim and strip 2 counterclockwise. If you have a flat surface, use mounting clips to secure the strips in place as you go. If you want to mount the strips under your pool rim, drill small holes in the trusses approximately every 2 feet. Use cable ties to anchor the strip to the truss. You can also use speed nuts or cotter pins for strip anchoring to avoid drilling holes.

Solder a small section of 22-gauge four-conductor wire onto the strip’s end terminals. To reseal the LED pool light strip, slide wires through the holes of a 10-mm end cap, fill the cap with silicone, and slide it into place on the end of the strip. Be sure to cover all of the exposed conductive traces to ensure water resistance. Allow a minimum of two to three hours for the sealant to cure.

7) Once the new end wires are attached to the strip, you will mount the amplifier. Use the double-sided 3M foam pad to mount the amplifier in the middle of strip 1 and strip 3. For best results and added security, apply 3M adhesion promoter to the amplifier and its installation location on the pool wall.

8) Using a dolphin connector, join each like-colored wire on strip 1 to the same color on one end of the amplifier. Do the same when connecting strip 3 to the other side of the amplifier. You should be connecting three wires in each color (red, blue, and green) together on each side of the amplifier. The black strip wire will be joined with white amplifier wire. Note that the separate group of just black and red wires are meant to be connected to the power supply. Follow the same instructions for connecting strips 2 and 4 to the amplifier on the other side of the pool.

9) Use 18-gauge wire and dolphin connectors to connect the amplifiers to your power supply.

10) Plug the power supply’s attached cord into an outlet, and enjoy your LED pool lighting system! Refill your pool with water, but make sure to leave space between the water line and the lights.

For more LED pool lighting options, see our entire selection of waterproof color-changing LED strip lights.

For technical questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

The frequency of accidents caused by the incorrect usage of electricity has increased as our dependency on electronic devices has increased over the last several years. Every year, accidental electrical fires cause millions of dollars in property damages. Because of this, you should always practice as much electrical safety as possible whenever you use your electrical appliances and devices. To make sure that your home is as safe as it can be from electrical accidents, you should also consider talking to an electrician in Glendale about performing an electrical safety assessment, updating service panels and ensuring that your home is properly grounded.

Can you use any size fuse or circuit breaker in your electrical panel?

Many older homes still utilize an outdated fuse box inside the service panel, instead of a safer and more modern breaker panel. If you still have a fuse box, then it is very likely that your electrical system is not prepared to take the amount of electricity that you use every day. This results in fuses blowing very frequently for many homeowners. Rather than replacing blown fuses with the appropriately sized replacements, some homeowners choose to oversize the fuse in order to reduce the frequency of blown fuses. This can be very dangerous, though not nearly as dangerous as replacing the fuse with something that cannot blow, such as a coin. Doing either of these should be avoided. Fuses are protective devices that are designed to stop electricity from flowing into a circuit whenever it reaches a level that is dangerous. Whenever you oversize or bypass a fuse, your circuit can overload. This can lead to overheating, fire and electrical shock.

One of the best ways to deal with an older fuse box is to have your electrical service upgraded by one of the technicians at The Electric Connection. We can send someone out to upgrade your service, and install the appropriately sized circuit breakers in your new electrical service panel. If you are experiencing any issues with your electrical panel, please don’t hesitate to give us a call today.

Click here to visit our website.