The type of in-wall wiring and cables you choose for your home will largely depend on what kind of signal you need to carry, where you’re going to route the wire, and how far the signal will have to travel between your various peripherals. Whatever type of wiring you choose to go with, you want to be sure you get one that’s rated for in-wall use by the Underwriters Laboratory (UL). This is usually going to be indicated with a CL2 or CL3 rating when it comes to speaker wire and audio/video cables. A good number of Ethernet cables are rated for in-wall use as well, usually indicated with a CM, CMR, or CMP rating. When choosing the right rating for each specific type of wiring, the UL looks at a range of different factors, including the heat being generated from current flowing through the wire, how quickly the cable will catch and spread fire when exposed to flame, and the wire’s vulnerability to damage from external stresses.

It is also important to look for a cable that’s rated for your specific needs. For instance, you are going to want cable that is rated as CL2P or CL3P if you are planning to run it in your heating ducts, or if you are looking to run your cable underground to connect to your outdoor speakers, you will want to make sure your cable is rated for direct burial. It should also be noted that when you are making the decision of what custom wiring you will need for your home, you need to be aware of your local fire codes and make your selections accordingly.

When you are looking for the right type of speaker wire for your home, there are two things you need to factor into your decision: the gauge and number of conductors. The gauge of wiring you choose should depend on how far the wire is going to have to travel from the receiver to the speaker. Significant power loss can occur over long runs of wiring, reducing your system’s performance. This might not be a significant issue in a single-room setup, but it is something to keep in mind if you are looking at a multi-room system. In terms of conductors, speaker cable comes with two or four. Two should be all you need for wiring a single speaker, but if you are looking at doing a multi-room setup, or a system with volume controls, you will mostly likely want four.

No home wiring setup would be complete without a solid Ethernet setup, but knowing which type of wiring to use can be a little confusing. When you are looking to create a wired computer network in your home, or carrying audio/video and control signals all across the home, CAT-5 cables have been the standard for a long time, but a better option these days might be to look at CAT-5e or CAT-6 cables. These newer cables are able to pass more data along the wire at a much faster rate than the older wires. The CAT-5e and CAT-6 wiring options are also backwards compatible with devices that were designed to work with the older CAT-5 wiring, meaning you won’t have to buy all new equipment. Ethernet cabling actually stands up to interference better than almost all audio/visual cables, which is a large reason it has become so popular in recent years for whole-house audio/video systems. It can also be a more cost-effective option to run long lengths of Ethernet cabling than it can be to run the same length in audio/video cable.

Any time of the year is a good time to save money, especially when it comes to the issue of one’s electricity bill. However, it is very understandable that the summer season is when one’s electricity bills tend to go straight through the roof because of the increasingly hot weather! This summer season, make sure that you end up saving some money on your electricity bill with the following energy savings cost cutting tips.

For starters, make sure that you keep your TVs and also your lamps quite a distance away from your thermostat. You see, both TVs and lamps emit heat, therefore prompting your air conditioning to actually run excessively and more than it really has to! Instead, place your TV and lamps across the room and think hard about switching to compact fluorescent bulbs.

Insulation is yet another thing you should do properly if you want to attend to your energy savings and your summer electricity cost cutting steps. You ought to insulate in an intelligent manner, for one thing. This means that you should look to insulate in some areas more than others, such as the attic. When you insulate your attic, you actually lower the negative effects of the heat that stem from the scorching rays of the sun. If you do this correctly, you are going to stop the heat that tends to build up on top of your home from actually filtering down to the rest of the residence.

Sometimes, your summer electricity cost cutting measures are so simple that they may even seem deceptively…simple! Take for instance the issue of your windows. When days get really, really hot in the summer months, just remember to close either your blinds or your curtains prior to leaving for work in the morning. This will minimize the effect of the sun’s blistering rays from beating down into the various rooms of your residence, thereby warming up your home to unbearable levels. As a sweet bonus, the fading effect of the sun’s rays to your rugs and your furniture will also be minimized.

Finally, you should use your microwave more than the oven for when you are preparing dinner. If you utilize your microwave, you can efficiently get your dinner ready in just a few minutes rather than an hour, and you will also be generating a lot less heat than if you utilize your oven!

So as you can verily see, there are a lot of things that you can do with regard to saving some money on your electricity bills over the summer. All that matters is that you have to be committed to adopting some of these money saving tips over the summer.

Have you recently had a home inspection completed or are you getting ready to purchase a home and don’t understand the inspection report? A certified electrician at ElectricMan can help you figure out exactly what the inspector found and what it all means. Having your home inspection deciphered by ElectricMan can save you time, money and a lot of stress.

Here are some examples of the most common home wiring problems that a certified electrician can remedy:

These problems may be eyesores, or perhaps you don’t notice them at all, but almost all of them can be hazardous and require immediate attention by a certified electrician. Before you start worrying about your latest home inspection and get knee-deep in all the repairs at once, ElectricMan can help you decode each project and give you a quote on needed repairs. Remember, it’s about your family’s safety, so it’s always best you pick your electrician based on the quality of work and his reputation rather than letting the seller pick the repairman.

If you suspect your home is subject to some of these problems, or for help interpreting your home inspection contact a certified electrician at ElectricMan today. ElectricMan is a trusted, local Dallas electrician with 27 years of experience. For more information visit the ElectricMan website and don’t forget to ‘like’ us on Facebook and follow us on Twitter, Pinterest and YouTube.