It is a cold October evening and you are preparing dinner. You are in full motion with all your appliances working overtime to get the meal done as soon as possible – and the power shuts off. Not only are you frustrated because you are set behind schedule but now you have to try to fix the problem. This happens to people on a daily basis and is a nuisance that can be avoided with the right electrical usage and correct setup. Lets walk where you should go from here.

As we have discussed in the past, the electrical panel (or breaker) is an integral part of the home’s electrical system. It regulates all incoming electricity and manages it throughout your house. When a breaker shuts a circuit off, or it “trips”, it is protecting you and your home from a potentially dangerous situation. The breaker will shut off that circuit because it has detected high voltage, high temperature, or another internal problem. If the breaker does not trip the circuit that is affected can overload and create an electrical shock or electrical fire.

To get your electrical breaker back on, identify the circuit that is in the off position and flip in back to the on position. With a properly labeled electrical panel it can be easy to quickly identify the affected circuit. If the breaker feels hot the touch or the circuit immediately trips again, do not attempt to turn it back on and call an expert electrician. Sometimes a circuit could trip due to a high amount of usage and may only be a minor problem with no repercussions. But if the breaker immediately trips when turned backed on or it trips regularly, there is a larger cause and the problem should be addressed as soon as possible.

There are a number of reasons why breakers could trip. The circuit that is being turned off could potentially have too much load and being overloaded. There could also be a problem in the wiring itself that is causing electrical surges and shorts that the breaker is detecting. It could also be a problem with the breaker itself. The panel may be old and reaching the end of its functionality. It may be time for the panel to be replaced.

It is not a good idea to keep turning on your breaker if it continuously trips. If you cannot identify a pattern in your routine that is causing the trip you should contact an Expert Electrician. They will be able to tell you if the problem is originating from the wiring or within the panel and even fix the problem for good.

Don’t put up with tripping breakers, it will become more than just an inconvenience. Get the right help and have peace of mind that your home is safe and dinner will get finished on time.

Under-Cabinet LED Lighting Kit is available for purchase that contains a plug-and-play LED light strip, push-button dimmer, remote, 12V power supply, and connection accessories. If you want to build a custom kit, follow the steps below the diagram to ensure that you get everything you need.

3. Select a dimmer or controller

For single-color LED strip light setup

Select the power supply large enough to operate the amount of LED strip light you need to use. If you want to control the brightness of your light strips, you will need a Single-color dimmer shown installed with a non-dimmable power supply

For color-changing LED strip light setup

Follow the instructions above for the single-color light strip setup. However, instead of a dimmer, use a RGB color-changing light strip installation

4. Use an LED amplifier for long runs of strip

Depending on the strip chosen and its maximum run (the number of strips that can be installed consecutively before needing amplifiers), you will need to install an light strip interconnect cables. It is best to purchase a length of strip that is more than your application requires. For example, if your project requires 8 1/2 feet of strip, we recommend purchasing 9 feet of strip to ensure that you have everything covered.

Having access to a 24/7 emergency electrical service is a necessity, not a luxury. There’s no telling when something in your house’s electrical system might malfunction, and a quick response is crucial. At the same time, you might feel tempted to try your hand at fixing the problem yourself to save time and cut back on expenses. This is a big mistake, one that can jeopardize your safety while also costing you more money and time than you were hoping to save in the first place. Getting help from the professionals is by far the best way to handle electrical problems safely and effectively.

Of all the reasons you shouldn’t try to perform electrical repairs yourself, the most important is the very real risk of hurting yourself. Electrical work can be dangerous, which is why experts go through so much training to do their job. Remember that every electrical system packs a huge punch of power, and a shock could be enough to injure or kill.

Even if you think you’re knowledgeable enough to do the job yourself, there is always a chance of running into complications that only a professional can handle. Calling for 24/7 emergency electrical service is the right choice — your safety is too important to gamble with for the sake of saving money.

If you’ve fallen victim to a serious electrical issue, trying to get the problem resolved quickly can backfire if it ends up being more serious than you suspected. A minor repair that seems to help the problem at first could be covering up a more critical issue, which could become a costly problem later on.