Let’s face it—halogen and incandescent headlight bulbs are a thing of the past. fanless, driverless LED headlight bulbs were used in this installation.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points. Repeat these tape lines for your other headlight.

6. Remove your headlight assembly if necessary, remove the current bulbs, and install your new LED bulbs. Check your owner’s manual for specific instructions on how to replace your headlight bulbs.

7. Depending on your vehicle, you may have to adjust your headlight beam before or after the assembly has been reinstalled. Your owner’s manual will explain how to adjust the beams. Align each headlight so that the top edge of the beam is at the same height as your horizontal line(s). If your headlights can be adjusted horizontally or produce two light cutoff points, use the vertical tape lines to align them properly.

3. Shake the vehicle to ensure that your suspension system is settled. For more precise adjustments, inflate all tires to their designated psi capacity and have someone sit in the driver’s seat. Also, make sure that your vehicle’s gas tank is at least half full.

4. Measure from the ground to the center of your headlight assembly where the bulb is located. This step must be done for all vehicles. If your vehicle allows for horizontal headlight adjustments in addition to vertical adjustments, it’s important that you also measure the distance between the centers of both headlight bulbs. The vehicle featured in this video allows for vertical headlight adjustments only; therefore, center lines aren’t necessary but are shown for demonstration purposes.

5. Turn on your low-beam headlights. Using painter’s tape, mark your headlight measurements on a flat wall. Measure from the ground up, and apply a horizontal line of tape to the wall; this line represents the top of your headlight beam. You can either apply one long, continuous line or small sections where the brightest areas of the headlight beams are shown.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points.

Fun Fact:  “To talk turkey,” means to speak candidly, directly, plainly and/or bluntly. There are several possible explanations to the origin of this phrase.  Some support a link to uncensored familial conversation around the Thanksgiving dinner table; Others say the phrase is linked to the actual sounds a turkey makes, because the male turkey’s “gobble, gobble” is a basic, unadorned, matter-of-fact kind of vocalization.

Wherever your holiday “turkey talk” may lead, Capitol Lighting’s Thanksgiving feast is sure to please everyone with custom designed lighting at unbeatable prices.  The lighting experts at Capitol will help you to illuminate your home for the holidays…elegantly, efficiently and affordably.

A little light goes a long way to bring charm and soothing illumination to the home environment.  Crystal mini chandeliers, mini table lamps, and other mini lighting fixtures create the stylized finish to designer decorated home interiors.  Feast your eyes on Capitol Lighting’s most outstanding selection of the season!

Add to your Thanksgiving holiday with the latest lighting designs from American Brass and Crystal Lighting.  Capitol Lighting invites you to take advantage of promotional pricing on ABC’s masterful works of art, including mini table lamps and crystal mini chandeliers available in a myriad of finishes including Antique Pewter, White Nickel and True Brass with crystal options ranging from Golden Teak Strass Teardrops to colorful Strass pendoloques.

Give Thanks for the Little Things

Capitol Lighting Highlights the “Mini Strass”

Warm up the room.  Instantly create elegance. Provide your home with charm! The mini chandelier has become an increasingly popular lighting fixture and accessory in home decorating schemes due to its versatility and small size. With extraordinary styling and imaginative design motifs, mini table lamps, too, are gracing more homes than ever.

Capitol Lighting’s Top 5 “Mini Must-dos” for a Superb Finish

To view the latest in home lighting and accessories and for more designing ways to put the mini on your menu this Thanksgiving, visit with the lighting professionals at Capitol Lighting.

Enjoy designer discounts on the best from American Brass and Crystal Lighting available this week at Capitol.

American Brass & Crystal (ABC Lighting) has built a reputation as one of the premier manufacturers of the finest quality cast brass and crystal mini chandeliers. All crystal chandelier and cast brass frames are molded in Italian casts by some of the finest metal craftsman in Europe and are then adorned with genuine Strass crystal from Swarovski. Each crystal mini chandelier from American Brass & Crystal Lighting is available in any of their 17 custom finishes and a multitude of different crystal grades, shapes and colors.

Visit a Capitol Lighting showroom or shop on-line at 1800lighting.com to custom designs your holiday illumination.  Enjoy promotional values on the latest mini lighting fashions from ABC.  The options abound; with American Brass & Crystal you create a design in a crystal chandelier that is uniquely your own and each one is hand made by American artisans with meticulous care.

Motion sensor LED stair lights let you safely and effectively navigate your steps while eliminating the need for any action. And because they turn off automatically, they also save power! We’ve recently installed these handy little LED stair lights and wanted to share the process with you.

wire that will be needed. It is best to order more than you need so that there’s slack in the line and enough to extend to where your power supply will be mounted.

It’s important to choose the correct wire gauge for the length of wire you need and amount of current that will be flowing through it. The key is to avoid voltage drop, which happens when the supplied energy of a power source is reduced as electric current flows through wire (or any other pieces of equipment that do not supply voltage on a circuit). The longer the run of wire, the lower the gauge of wire needed.

*If you need help determining the correct wire gauge, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

3. Using wiring from the

4. Use a run of wire to join the PIR sensor at the top of your steps with the power supply. You can wire both PIR sensors to the power supply using electrical tape or with

5. Connect your main line to the PIR sensor at the bottom of your steps, and begin connecting each step light with

7. Finally, connect to power.

LED stair lights and

4. Connect your main line to the PIR sensor at the bottom of your steps, and begin connecting each step light with

6. Finally, plug the power supply into your wall outlet.