Every home has a fire detection system. This vital safety feature should be well understood. Smoke detectors, carbon monoxide detectors and security systems give homeowners peace-of-mind. Furthermore, when combined with a security system, these devices work together to form a complete home protection plan.

The second type of detector is an ionization detector. It uses a small amount of radioactive material to ionize the air in an internal chamber. This in turn, generates a voltage that can be measured. By-products of combustion will change the voltage that is generated and trigger the alarm. This type of detector is better at identifying active combustion with little to no smoke.

While both types of smoke detectors will safely alert a homeowner to a fire, combination alarms exist that employ both methods. Consequently, the responsiveness of the whole system increases. Hard-wired detectors are also available which can be wired to trigger all the alarms in a home if anyone detects a problem.

In any appliance that uses combustion, such as a furnace or stove top, a potential exists for hazardous carbon monoxide buildup. This by-product is tasteless, odorless, colorless, and highly toxic in large concentrations. Therefore, a carbon monoxide detector is highly recommended. It will monitor the levels of CO in the air and alert inhabitants before they become dangerous. They are available as stand-alone units that can be plugged in to standard wall outlets or as combination roof-mounted CO and smoke detectors.

Home security systems have been around for decades and make use of a combination of sensors including door, window, glass-break, and motion sensors. Historically, these devices were hard-wired and fed back to a central control panel. Many modern systems make use of wireless sensors that allow for easy retrofitting of existing homes. Door and window sensors utilize a small magnet and magnetic strip held open when the door or window closes. If the magnet is moved away, the magnetic strip springs closed and triggers the alarm.

Glass-break sensors are placed near windows and use a microphone to listen for the distinctive frequencies associated with glass breaking. Motion detectors take advantage of a variety of technologies, such as passive infrared, microwave, or ultrasonic. This technology detects something moving within its range. These can be part of exterior security lights or interior motion sensors. Security cameras can also play a role in home security. Install them indoors or outdoors.

When installed and used properly, a home security system can easily increase home safety while reducing the chances of burglary or fire. Most insurance companies offer discounts for home security systems. Because of this, the entire cost of the system may be offset or eliminated altogether. Be sure to ask your insurance company about discounts to homeowner’s insurance for improving or installing a new security system.

Transforming a basement into livable space is a big deal. It requires a lot of planning, work and execution. If you have a basement, you have a lot of space down there that you could be using to entertain, as bedrooms or simply to add value to your home. When done correctly and up to code, your basement can count towards the total square footage of your home. Every additional square foot adds anywhere from $50 to $200 to your total value depending on where you live. An electrician in Glendale, like those at The Electric Connection, can help you get that remodel underway and up to code in no time.

Basements are generally already wired with electricity, but the lack of walls, ceiling and more than a cement floor are an issue. Once you add flooring and put in a ceiling, the ceiling height tends to be a bit smaller than the average. However, it is still functional and as long as it meets the building code, you can make it work. Now, basements tend to be dark, but you can change that with the installation of recessed lights by an electrician. Glendale homeowners will not have to worry about losing any head room with these lights because they are flush with the ceiling.

You can add several lights that will really brighten up the space. Whether you are transforming your basement into a den or the ultimate game room, you want to preserve as much ceiling space as possible while providing plenty of light. If you are dividing the area into separate rooms, your Glendale electrician can add the wiring needed for the outlets as well as the light switches needed to operate the lights in each space. A basement remodel is a fun project that is rewarding and will provide an excellent return on your investment. Give The Electric Connection a call today and schedule your lighting installation.

It is true that most of the electrical problems you have in your home will need to be taken care of by a licensed electrician. However, there are various smaller problems that you can easily and safely troubleshoot. Here are just a few:

This can be quite bothersome and yet pretty easy to troubleshoot. Begin by checking that the bulb has been screwed in correctly. It needs to be in all the way. If that is in order, check to see that the wattage is correct for the fixture in which it has been fixed. If the wattage is not right, that can be causing overheating and it can even lead to a fire. In the event that the wattage is correct, just replace the old bulb with a new one. If the light is still flickering, then it is possible that the electrical outlet or the cord has a problem.

Fun Fact: His obsession with a chandelier led Italian astronomer, mathematician and physicist, Galileo to discover the law of pendulum motion.

While, we cannot guarantee that you will understand the laws of physics, we can guarantee that you will be captivated by the brilliance of a chandelier.

More than ever, we are experimenting with home lighting design to display our individuality, and nothing conveys unique style more than a fabulous chandelier.

Professional lighting consultants at Capitol Lighting can help you to illuminate your sense of style and find the perfect chandelier(s) to complete your decorative interior design.  A few simple laws of lighting and trusting your own good taste will get you there…

Chandelier Application and Design Tips from Capitol Lighting

Outstanding Applications:  From powder rooms to dining rooms, the chandelier enhances the appeal of your home environment. Chosen above all else for their aesthetic rewards, chandeliers also provide needed general ambient illumination.

Power in Proportion: To enjoy the full benefits of a chandelier, you must choose a fixture that is the correct size.  A chandelier that is too big will overpower; one that is too small will look out of place.  Finding the right chandelier size is easy:  Add the length and width of the room in feet, and then convert that number to inches (i.e. a room that is 12 feet by 16 feet would require a chandelier that is approximately 28 inches wide). When in doubt between available chandelier sizes, size up to achieve a more balanced presentation.

Special Considerations for Over Dining Tables:  When hanging a chandelier over a dining table, the total chandelier width should be about a foot smaller than the table width to allow approximately a 6-inch clearance for those seated around the table.

The Long and Short of It:  Over a dining table, the bottom of the chandelier should hang about 30 inches over the tabletop. The height of the fixture should measure about three inches for each foot of ceiling height, so for standard 8 foot ceilings choose a chandelier with an approximate height of 24 inches.

In a one-story foyer or in rooms with standard 8-foot ceilings, a chandelier should hang no less than 7 feet from the floor.  In a two-story foyer or in rooms with higher ceilings, the chandelier should hang approximately 8-10 feet from the floor. If your foyer fixture is to be viewed through a picture window, select a chandelier that will fill this space and center the fixture accordingly.  Note:  A two or three-tiered chandelier works best for rooms with higher ceilings.

Installation Awareness:  Be sure to employ a qualified electrician and follow National Electrical codes when installing fixtures.  It is especially important to consider the proper mounting procedures for hanging a heavier chandelier.  Usually fixtures weighing 50 pounds or more must be secured to the home’s permanent structure.

Maintaining the Glamour:  Keeping your chandelier in pristine condition requires proper cleaning and attention to specific instructions pertaining to certain finishes.  Generally, crystal and glass elements are kept clean with a basic soap and water combination.  Nonabrasive cleansers for most finishes are required.  Drying fixture components completely will help protect their luster.

Best Accessories:  Ceiling medallions, chandelier shades, decorative chain and cord covers may add to the ambience of the chandelier.  These items may be special ordered to give your chandelier a unique flair.

Imperative Additions:  Be sure to use the correct bulbs for your chandelier.  Where you have a choice between frosted or clear, choose the bulb that goes best with the fixtures finish.  Always employ dimmer controls with your chandelier.

Get High and Mighty with a Mini: The mini chandelier has become an increasingly popular lighting fixture around the home due to the versatility of its small size. Many designers are opting for mini chandeliers, rather than pendant or island lights, over long dining room tables and kitchen islands. Mini chandeliers are also gracing powder rooms and master bathrooms, as well as bedside tables.

Accent the Positive:  Although the chandelier should be the main lighting attraction, low-voltage spot lights, a matching torchiere floor lamp, +/or coordinating wall sconces make great designing additions to supplement lighting needs and complete the room’s décor.

The lighting experts at Capitol guarantee that you will captivate guests and enjoy your home to the fullest with the most illuminating fashions in home lighting and accessories.  Capitol Lighting’s lighting consultants can help you find the perfect chandelier for your home and give you tips on hanging a chandelier.

Many homeowners know the pride and satisfaction that results from completing DIY repairs and improvements. But when it comes to electrical work, the stakes of making a rookie mistake can be high.

There are several common electrical projects that aren’t complicated or extensive, but even the simplest jobs can result in serious injury or property damage if they’re performed improperly. Before making any plans to engage in a DIY electrical project, it’s important to know the risks.

What Can Go Wrong

Electricians undergo an enormous amount of training in order to earn the licenses and certifications they need to do their work. That’s because mistakes could not only be dangerous for them, but also for anyone in the homes or buildings they’re working on. Even if you know your way around the circuit box, here’s what an electrical mishap can bring:

Hiring Electricians Saves Money

One of the most common reasons why electrical novices attempt this sort of work is to save money. But that plan can easily backfire even if no one gets hurt in the process.

Poorly performed electrical work can spark destructive fires. It can also fry circuits, destroy fixtures and even damage major appliances. When things go wrong, the cost of repairs is usually several times what it would cost to hire an electrician in the first place.

Making matters much worse, homeowners insurance companies will typically ask for confirmation that electrical work was performed by a licensed electrician before covering any damage from a related event. If your insurance carrier learns that you did the work on your own to save a few dollars, you could lose your claim or even invalidate your policy. Be sure you understand your full policy details before engaging in DIY work.

Know the Code?

When you hire an electrician, you’re not just passing the risk along to a professional -- you’re hiring someone who has knowledge you don't even realize your lacking.

Electrical work is constantly getting safer and more reliable through updates to the electrical code. Licensed electricians are required to keep up with this code as it evolves, so when you work with a professional, you can count on receiving the safest electrical work possible. When you go it alone, you may follow outdated methods because you weren’t aware of the code update.

Don’t take a chance. Your life and home are too valuable. When you need electrical work performed safely and properly, call upon your knowledgeable, licensed, local electricians.