It seems like everything you buy today requires an electrical outlet. If you find yourself living in an older home or one with out-dated wiring, you could also end up at a loss for power. With electrical outlets spread sparsely around your home, it can be difficult to find enough outlets to plug in a lamp at the location you want or plug in all your electronics in the same spot. Fortunately, you do have some options for expanding your electrical accessibility and capacity.

The most common fix for this problem is to use extension cords. Extension cords can go extend as far as 150 feet, but are not always an ideal permanent solution. If you were running a significant amount of power through a long running extension cord on a regular basis, it would be a better idea to install an outlet at that location. With a heavy loaded extension cord you run a greater risk of fires and overloading the circuit. Undersized extension cords can overheat and cause a fire. If you will be running several electronics of the same outlet (television, computer, entertainment system) you should invest in a power bar with a surge protector. A power bar will be able to handle the larger electrical load and protect your valuable electronics from surges.

Another option would be to use an adapter to split two standard electrical sockets into four. This can be helpful when you need to plug in an additional lamp or phone charger in your room. If you find that you are tripping your breaker when you are plugging in more devices or appliances onto an adapter, power bar, or extension cord, you are probably overloading your circuit. The best course of action would be to have an electrician install a new outlet on a separate circuit.

While having new outlets installed by a professional electrician is the safest idea, it is not always possible in every situation. If you are a renter you may not be able to or want to upgrade the current electrical system. Or it is possible that your current breaker or electrical panel may not be able to handle additional electrical outlets. If that is the case, have a licenced electrician inspect your home electrical system to ensure that you are able to safely add on additional outlets. While planning for new outlets, identify areas that would be optimal for having power and covering the room appropriately. This way you can avoid problems down the road and installing an excessive amount of outlets in one room.

It is important to use undamaged extension cords and not run one extension cord off of another. For the best peace of mind, have one of our electricians install an additional circuit and outlets in your home. This will keep your home up to code and reduce the risk of fires significantly.

The weather outside bas been quite hot as the temperature has been reaching and exceeding the 30’s lately. Your electrical bill is probably rising with the temperature as well. Now is the time that many people start visiting stores in search of an air conditioning unit. This is a great way to cool down your home, but if your home’s electrical system is not prepared for the electrical load or you purchase the wrong unit, you could be left sweating more money than you expected.

Window-mounted air conditioning units are quite common to see in bedrooms or living rooms. These can be purchased from any local home appliance store. These units are mounted in the window and secured. These units pump in cold air and exhaust hot air to the outside – great for rooms that are frequented and difficult to keep cool.

The small units can also be purchased from your local appliance store. These smaller units cannot cool the same amount of area as a window-mounted unit, but can do the trick for small areas that you want to keep cool. The advantage of these is that you can move them from room to room quickly with little setup and takedown. One disadvantage of these units is that they tend to be quite noisy.

You may be fortunate enough to have one of these installed in your home. Central air units can be connected by ducts throughout the house and regulate the temperature set in the home. A central air unit is great for getting a consistently cool temperature in any room in the home while also keeping the noise to a minimum. One trick when it comes to central air is to ensure that you get a unit that matches the square footage for your home. If your air conditioning unit is too large for your home it may not properly dehumidify your home and run on short cycles.

When purchasing an A/C unit you want to ensure that you have a timer and energy-saver option. This will help keep your monthly electrical bills down. Energy efficient units will use less electricity and timer options can prevent the units from running when they are not needed. You also want to make sure that the unit is the appropriate size for your room or home. If the unit is too large it will cycle off quickly and can freeze air moisture without removing it, which can lead to a higher electrical bill.

If you are in the market for a new air conditioning unit for your home, make sure you do adequate research to ensure you are purchasing the right unit at the right size. Read the package for the required voltage and wattage. If you are adding an A/C unit in your home you could overload electrical circuits that are no prepared. If you have questions about your home’s electrical efficiency in the summer, call Expert Electric at 604-681-8338.

For large projects, a simple notepad and pen are not sufficient to provide accurate and timely cost estimates to clients. The good news is that there are some pretty good estimating software programs now available that do the job. Both residential and commercial contractors can save time, money, and win more bids by providing professional job estimates. These programs also offer the ability to manage projects, bill clients, and keep track of change orders. They feature a wide range of options for any size of contractor.

TurboBid is one of the most well received and fully featured estimating programs on the market. It contains a user-friendly graphical interface and offers training courses through their website. The software can connect to national and local material supplier databases to keep pricing updated throughout the bidding process.

Change orders and revisions are simple. The software will generate automatic reports and professional presentations for clients. It also allows fine adjustment of man-hour estimations in different locations of the building. This includes ceilings. The program can account for different worker skill levels and upcoming wage increases for longer projects.

The built-in database includes tens of thousands of parts and full assemblies to allow for quick and easy estimation. The program incorporates national and local electrical code requirements to ensure bids are code compliant. In addition, it has a value engineering feature that suggests code-compliant changes to the customer’s blueprints. This can ultimately save money by adding, removing, or relocating devices.