Outdoor lighting of many varieties can effectively keep your space well-lit, safe, and inviting for you and your guests. These lights are typically reliable and long-lasting, but if they stop working and leave you in the dark, it can be a frustrating experience. Having an understanding of your lights and their potential issues can help you if you need to conduct outdoor lighting troubleshooting. There are several types of outdoor lights, all with different looks and objectives. Spotlights provide bright, direct light onto a specific area. Uplights are installed at or below ground level to shine upwards onto objects while downlights are installed high in a tree or structure to shine down. Floodlights use a motion sensor to shine directly onto an area when they sense someone there. Path or walkway lights are installed as individual fixtures along a walkway to illuminate it. Solar lights gather energy from the sun throughout the day, then turn on at night. These lights are installed in a variety of areas such as on a home; on a deck;  around a patio, deck, sitting area, or pool; or on the ground. There are also a variety of bulbs including halogen, incandescent, LED (light emitting diode) and bug light, each with their own uses and benefits. Each of these fixtures has several parts and can be susceptible to different issues depending on their parts and assembly. If your lights aren’t working properly, it can be concerning, and create potentially dangerous situations.

water and vinegar to remove residue and keep your lights shining brightly.While some outdoor lighting troubleshooting can easily be done on your own, outdoor lights are complex fixtures that aren’t always easy to diagnose and fix.

Did you know there could be unknown home safety issues lurking in your presumed safe haven? Your home’s age, installation issues, wear and tear, and overlooking safety devices could put you at risk.

Does your home have any of the following home safety issues?

Code and Wiring Updates Wiring codes in the U.S. are updated every three years to ensure electrical safety across the country. As a result, families living in older homes are at an increased risk of electrical safety issues due to:

Ensure home safety with an electrical home inspection  Don’t let home safety issues result in property damage or present a danger to your family. Find and address home safety hazards quickly and efficiently with an electrical home inspection. Mr. Electric® can provide a detailed, prioritized written checklist of all areas of your home requiring immediate attention, areas for improvement, and potential upgrade possibilities to ensure the safety of your home. Ensure peace of mind by proactively addressing home safety issues. Contact Mr. Electric today. Our professional electricians are dedicated to the safety of your home and family.  

Aluminum LED profile housings allow you to create customized light fixtures with LED strip lights. Our Klus brand LED channels are available in many different styles, including recessed-, or flexible, O-shaped, and more. Available in 1- and 2-meter lengths, the channels can be easily cut for any application from under-cabinet lighting and bookshelf lighting to showcase lighting and transition strip lighting. They’re available with a variety of lens options, such as clear, frosted, and etched that complete the profiles. We’ve put together a step-by-step guide for using these channels to create your own light fixtures. Please note that your specific channel might vary from the one used in this tutorial.

Materials needed:

1. With a pair of clippers, carefully clip through the clear plastic heat shrink as shown in figures A-C. You will want to take your time and be careful not to cut the strip’s wires while removing it.

2. Lay the LED strip into the channel, and position it along the bottom so that the ends of the strip and the channel are lined up (fig. A). Now, remove the paper from the strip’s adhesive backing (fig. B), and adhere the strip to the LED channel—starting at the lined end and working your way to the other end of the strip. Be sure to leave roughly 1/4-inch free at the end of the channel so that you can install the end cap as shown in figure C.

3. If one of your end caps doesn’t come with a pre-drilled hole, you will need to drill your own to allow the wires of the LED strip light to come through. In this case, we used a Dremel tool, but other options are viable as well. Regardless of the tool you choose, it is helpful to mark the end cap where you would like the wires to come through. Start the hole small, and increase the size as necessary.

4. Place the end cap on the wired side of the strip by threading the wires through the end cap as shown in figure A. Insert the end cap into the end of the light bar, and push firmly until it is fully in place (fig. B).

5. On the open end of the bar, slightly peel up the end of the LED strip (fig. A); this is necessary to install the end cap. Now measure your channel lens, and trim off the excess with clippers (fig. B). Be careful when trimming to avoid cracking the plastic. Excess material can be lightly sanded off. Once the lens has been cut to the proper length, slide it into the channel, and install the end cap as shown in figures C and D.

6. That’s it! Your customized LED light fixture is complete and ready for installation, which we will cover in the next step.

7. Mounting this LED profile is as easy as applying double-sided tape to the back of it and sticking it to your intended surface. Be sure to cut the tape to fit the back of the LED profile and to leave the tape backing on the side not attached to the channel until you are ready to mount it.

For most LED profiles, mounting clips are available for a more permanent installation.

If you have questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

Your home is constantly evolving. The people who live in it grow up. You may expand the family at some point or your family may shrink as the kids move on. With your ever-changing family, your home will need to grow and evolve with your needs. Remodeling your family home makes a lot more sense than pulling up stakes and buying a new home that will fit your needs for a short time. You can make your home fit your family by remodeling with the help of an electrician in Santa Monica. The team at The Electric Connection is here to help you realize your dreams.

A remodeling job is an exciting adventure as you work with a contractor to transform your home into one that you are proud of and completely comfortable in. Unless you are a skilled tradesman, you won’t want to try and take on this big job yourself. Your fun adventure will quickly turn into a nightmare that could not only put your safety at risk, but the safety of your home. It is imperative you leave all of the Santa Monica electrical work to a professional.

Prior to starting the remodeling process, you will want to have a conversation with your electrician and other contractors about what your goals are. Some points to discuss with your electrician are as follows;

• Replacement of existing light fixtures • Installing data lines

While the electrician is in the house, it doesn’t hurt to have an electric safety inspection completed as well. This will help you identify any areas that should be upgraded or replaced during the remodel. This will make your home safer and give you peace of mind. If you are ready to take the first step in remodeling your home, give The Electric Connection a c all today.