Is your LED bulb blinking too fast? No worries—it’s an easy fix! LED lighting draws much less power and lasts way longer than standard incandescent lighting that comes stock with most vehicles. Although the reduced draw of LEDs has advantages, replacement of turn signal bulbs with LEDS will cause what is called hyperflashing. Hyperflashing is when the turn signals blink faster than your stock incandescent bulbs did. This happens because your new LED bulbs draw such little power that your turn signal relay sees the bulbs as being out.

Installing an ixing hyperflashing. These modules are economically priced and are usually simple to install. In most cases, these flasher units are little circular or square boxes with metal prongs sticking out one side that simply plug into where your stock flasher went. Our LED flashers function with both LED and incandescent bulbs, so even if you have LED turn signals in the back and incandescent bulbs still in the front, you can use our LED flasher modules with no problems. Before you order, compare the pin diagram of the stock flasher with the pin diagram of our flashers on our website.

For technical questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

As a rule, the bottom of any hanging light should be at least 6’8″ off the ground – unless it’s over a table or island. When you have an 8′ ceiling, this doesn’t give you a whole lot of room to play. If you long for the grand impact of a decorative

A room with a single light fixture is depressing. Kick the shadows by adding multiple light sources. A few stylish flush-mount ceiling lights. Some table lamps. An accent light here or there. When you have multiple lights shining in different directions, the space will feel lighter and more open. Make sure to place ceiling lights at least 3′ from the wall, any closer and harsh shadows will make your ceiling seem lower. 

Aluminum LED profile housings allow you to create customized light fixtures with LED strip lights. Our Klus brand LED channels are available in many different styles, including recessed-, or flexible, O-shaped, and more. Available in 1- and 2-meter lengths, the channels can be easily cut for any application from under-cabinet lighting and bookshelf lighting to showcase lighting and transition strip lighting. They’re available with a variety of lens options, such as clear, frosted, and etched that complete the profiles. We’ve put together a step-by-step guide for using these channels to create your own light fixtures. Please note that your specific channel might vary from the one used in this tutorial.

Materials needed:

1. With a pair of clippers, carefully clip through the clear plastic heat shrink as shown in figures A-C. You will want to take your time and be careful not to cut the strip’s wires while removing it.

2. Lay the LED strip into the channel, and position it along the bottom so that the ends of the strip and the channel are lined up (fig. A). Now, remove the paper from the strip’s adhesive backing (fig. B), and adhere the strip to the LED channel—starting at the lined end and working your way to the other end of the strip. Be sure to leave roughly 1/4-inch free at the end of the channel so that you can install the end cap as shown in figure C.

3. If one of your end caps doesn’t come with a pre-drilled hole, you will need to drill your own to allow the wires of the LED strip light to come through. In this case, we used a Dremel tool, but other options are viable as well. Regardless of the tool you choose, it is helpful to mark the end cap where you would like the wires to come through. Start the hole small, and increase the size as necessary.

4. Place the end cap on the wired side of the strip by threading the wires through the end cap as shown in figure A. Insert the end cap into the end of the light bar, and push firmly until it is fully in place (fig. B).

5. On the open end of the bar, slightly peel up the end of the LED strip (fig. A); this is necessary to install the end cap. Now measure your channel lens, and trim off the excess with clippers (fig. B). Be careful when trimming to avoid cracking the plastic. Excess material can be lightly sanded off. Once the lens has been cut to the proper length, slide it into the channel, and install the end cap as shown in figures C and D.

6. That’s it! Your customized LED light fixture is complete and ready for installation, which we will cover in the next step.

7. Mounting this LED profile is as easy as applying double-sided tape to the back of it and sticking it to your intended surface. Be sure to cut the tape to fit the back of the LED profile and to leave the tape backing on the side not attached to the channel until you are ready to mount it.

For most LED profiles, mounting clips are available for a more permanent installation.

If you have questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.