Let’s face it—halogen and incandescent headlight bulbs are a thing of the past. fanless, driverless LED headlight bulbs were used in this installation.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points. Repeat these tape lines for your other headlight.

6. Remove your headlight assembly if necessary, remove the current bulbs, and install your new LED bulbs. Check your owner’s manual for specific instructions on how to replace your headlight bulbs.

7. Depending on your vehicle, you may have to adjust your headlight beam before or after the assembly has been reinstalled. Your owner’s manual will explain how to adjust the beams. Align each headlight so that the top edge of the beam is at the same height as your horizontal line(s). If your headlights can be adjusted horizontally or produce two light cutoff points, use the vertical tape lines to align them properly.

3. Shake the vehicle to ensure that your suspension system is settled. For more precise adjustments, inflate all tires to their designated psi capacity and have someone sit in the driver’s seat. Also, make sure that your vehicle’s gas tank is at least half full.

4. Measure from the ground to the center of your headlight assembly where the bulb is located. This step must be done for all vehicles. If your vehicle allows for horizontal headlight adjustments in addition to vertical adjustments, it’s important that you also measure the distance between the centers of both headlight bulbs. The vehicle featured in this video allows for vertical headlight adjustments only; therefore, center lines aren’t necessary but are shown for demonstration purposes.

5. Turn on your low-beam headlights. Using painter’s tape, mark your headlight measurements on a flat wall. Measure from the ground up, and apply a horizontal line of tape to the wall; this line represents the top of your headlight beam. You can either apply one long, continuous line or small sections where the brightest areas of the headlight beams are shown.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points.

Technology is advancing at a dizzying pace. What used to be the ‘latest’ and ‘most advanced’ devices yesterday becomes redundant today. When people embrace any technology, they do so because it adds convenience, comfort and safety to their lives in one way or the other. When it comes to your home, all these three aspects matter a great deal. It’s why many people are now veering towards the smart home concept.

Sure, many homeowners already have Internet-based security systems and landscape irrigation systems that are connected to timers etc; but smart homes are designed and set up to do much more than that. Having a smart home is a lot about Wi-Fi connectivity and more. Take a look at some concepts; this will help you create a plan for your smart home.

It’s not uncommon for companies that launch smart home products to say that connecting their devices to the Internet is a breeze. Sure, they are bang on spot most of the times, but what actually matters a great deal is the Wi-Fi connectivity in your home. These are some of the things you will have to keep in view while planning your smart home:

This is vital, and it’s something you should keep in view while planning your first smart home. The longer the distance the radio waves have to travel, more the connectivity issues. The best way to overcome this kind of an issue is to install the Wi-Fi router at the center of your property and on the ground floor.

You will find a number of products which claim they are able to extend the Internet connection in your home. The simple fact is that multimedia over coaxial power-line adapters, network extenders etc tend to slow down the signal by around 50% and that reduces the consistency of the network. Of course, you won’t find any issues with driving a motion sensor or a smart bulb; however, you might just find it challenging to stream a movie to your tablet/laptop, only because it can’t figure out which Wi-Fi router it should connect to.

At times, installing a network of Ethernet cables turns out to be the best solution. You can use cable runs to install your smart home hub devices in spots that are more accessible. The devices that are connected to these hubs will function more smoothly if you do this. If your home is already wired for telephones, hardwiring for Ethernet won’t be too difficult. You will need to speak with your electrician and check whether he would be able to run an extra cable to the point you need it at, without too much of drilling and sawing.

When you are planning your smart home, ensure there are sufficient power points at different places in your house. While certain devices may be battery-powered, many aren’t. So whether it’s a Wi-Fi router/extender, web security camera etc, you will need a power point to plug them in. And of course you don’t want power cords dangling all over your smart home.

Very simply put, if you are building a new smart home or remodeling your existing one, sit down and plan not just for the current smart devices you plan to install, but for future ones as well. Map out a detailed plan and get some advice from the installer too. Coming back to the first point – focus on getting a very good Wi-Fi router and ensure its positioned at the right point on your property.

Very importantly, get a professional to do all the wiring work once you have your entire smart home plan in place. For more information about smart home device and hardwiring solutions, call Allround Electrical at 1300 169 263. You can also drop us a line via email or by filling out this contact form.

Thanks for reading,1300 169 263

We live a world that is very plugged in. All of gadgets that keep us updated with work, play and family require a charged battery that can only be achieved by plugging the unit into the wall. We have an electrical appliance for just about any task we have. All of this means we are very dependent on the electricity we are so lucky to have. Sometimes, our needs surpass the supply. How many times have you had to dig out an extension cord because you were short on outlets or you needed to charge your laptop while you were in an area that didn’t have an available outlet? It happens a lot. You need the services of an electrician, like those at The Electric Connection.

Additional outlets installed in your home or office can make life easier. It allows you to streamline your work space whether you are cooking dinner or working on a big project for work. You don’t have to figure out what to unplug so you can plug in another device. You can have it all with the help of an electrician in southern California. It doesn’t take a lot of work and there won’t need to be a complete remodel to add the additional outlets.

In some cases, the electrician may need to add an additional breaker to support the new outlets. This is generally when you want to run a large appliance, like a refrigerator or stove, or when you already have a number of appliances on the same breaker. This is something that will be evaluated before any electrical work is started. An additional breaker is usually not an issue. In rare cases, a panel upgrade may be necessary. This is usually for older homes that have limited breakers or outdated wiring. Give The Electric Connection a call today and get started on your way to electrical outlet freedom.