RGB LED strip lights are a great way to add a pop of color to your above-ground pool. These low-voltage LED lights can be applied to the inside rim of your pool or around your pool deck. With RGB LED strip lights, you can choose from a ton of dynamic color-changing and single-color modes with adjustable brightness and speed control. They’re great for parties or late-night swims and can be easily installed. We’ve included installation instructions for our waterproof LED strip lights. Some cities require above-ground pool lighting to meet National Electrical Code (NEC) Article 680 standards, which would limit possible pool lighting installation locations. Before you purchase LED pool lights, check your city’s code requirements. We also recommend that you have a certified electrician install your lights.

1) Before ordering your LED strip lights, measure the diameter of your pool and multiply by 3.14 to find its circumference; this number indicates the total length of strip that you will need. The 21-foot pool used for these installation instructions has a circumference of 65.94 feet and requires 4 runs of 16-foot LED strips.

You will also need to measure the distance between where your power supply will be and both sides of your pool where the amplifiers will be installed (see the setup and wiring illustration below). These distances will tell you how much 18-gauge wire you’ll need for connecting the amplifiers to power. Make sure to account for the distance of any dips or turns that the wires may take along their paths.

Lastly, measure the approximate distance that will be between your controller and where your strip lights begin. This distance will tell you how much 22-gauge wire you’ll need for connecting the controller to your strips. You will also need two small sections of this wire for connecting your first and second strip lights to the amplifiers.

2) Before you’re ready to install your LED strip lights, be sure to drain your pool. Begin by creating or locating a dry area away from your pool for the power supply. The power supply should be contained in a weatherproof box. Power supplies should be installed between a ground fault circuit interrupter (GFCI) protected circuit and the pool’s junction box. It’s crucial to use a GFCI protected circuit as it shuts off if current flows where it’s not supposed to.

Wire the included plug to the power supply, but do not connect to power until the installation is complete.

3) Connect your RGB LED controller to the power supply. Cut the barrel off of the controller wiring. Strip back the remaining wires, and connect its wires to the power supply.

4) Cut the LC2 connector off of the remaining end of the controller, and strip back the wires. Run 22-gauge four-conductor wire to connect the controller to your low-voltage pool lights; use dolphin connectors to join like-colored wires. Connect your first two LED strip lights to the controller by joining each set of like-colored wire with a dolphin connector. You should be connecting four wires of each color (red, blue, green, and black) together. For added protection, cover all wire connections in this installation with electrical tape.

5) You will apply strip 1 clockwise around your pool rim and strip 2 counterclockwise. If you have a flat surface, use mounting clips to secure the strips in place as you go. If you want to mount the strips under your pool rim, drill small holes in the trusses approximately every 2 feet. Use cable ties to anchor the strip to the truss. You can also use speed nuts or cotter pins for strip anchoring to avoid drilling holes.

Solder a small section of 22-gauge four-conductor wire onto the strip’s end terminals. To reseal the LED pool light strip, slide wires through the holes of a 10-mm end cap, fill the cap with silicone, and slide it into place on the end of the strip. Be sure to cover all of the exposed conductive traces to ensure water resistance. Allow a minimum of two to three hours for the sealant to cure.

7) Once the new end wires are attached to the strip, you will mount the amplifier. Use the double-sided 3M foam pad to mount the amplifier in the middle of strip 1 and strip 3. For best results and added security, apply 3M adhesion promoter to the amplifier and its installation location on the pool wall.

8) Using a dolphin connector, join each like-colored wire on strip 1 to the same color on one end of the amplifier. Do the same when connecting strip 3 to the other side of the amplifier. You should be connecting three wires in each color (red, blue, and green) together on each side of the amplifier. The black strip wire will be joined with white amplifier wire. Note that the separate group of just black and red wires are meant to be connected to the power supply. Follow the same instructions for connecting strips 2 and 4 to the amplifier on the other side of the pool.

9) Use 18-gauge wire and dolphin connectors to connect the amplifiers to your power supply.

10) Plug the power supply’s attached cord into an outlet, and enjoy your LED pool lighting system! Refill your pool with water, but make sure to leave space between the water line and the lights.

For more LED pool lighting options, see our entire selection of waterproof color-changing LED strip lights.

For technical questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

The electrical system in a home is incredibly complex, and it can fall prey to a number of different repair needs. Although it’s tempting to try to fix what may seem like “little” electric problems using a few tools like a pair of pliers and electricians’ tape, you should avoid this “do-it-yourself” temptation at all costs. The power coursing through the circuits in your home could cause high voltage shocks and or lead to electrical fires. Only entrust the repair work to licensed electricians from a reliable contractor.

Pay close attention to any signs in your house that there are electrical repair needs: flickering lights, power surges, sparking light switches, acrid burning smells, etc. Turn off the power and immediately call for licensed electricians; you never want to risk injury or a fire.

Fluorescent ballasts are used in many industrial warehouses as they offer cheap and efficient lighting. These ballasts can last decades but depending on the type of environment (extreme cold/extreme heat), may be subject to a shorter lifespan. Check your ballast fixtures for these warning signs to see if it is time for a ballast replacement.

There are several signs that can indicate to you that it is time to replace your ballast these include:

If your ballast fixtures have any of these signs, it could mean that they are in need of replacement. Before scheduling and planning to have your ballasts replace, replace the bulbs with brand new bulbs. At times issues can relate to a specific bulb and not the ballast, giving off false symptoms.

For many handy people, they will feel confident in replacing a ballast themselves. If you are replacing a ballast yourself, please use the proper protective equipment and ensure that all power to the ballast is turned off to prevent electrocution. As part of the ballast replacement you will be required to cut and rewire the electrical wires. This can be technical and a mistake in the process can result in damage to the new fixture, bulbs, and possible electrocution. If you are not comfortable or knowledgeable with the process of ballast replacement, we would highly recommend that you contact a licenced electrician to complete the installation for you. This way you can be sure you will be left with a working ballast that is correctly installed and safe.

If your workplace, garage, or home is in need of ballast replacements, contact Expert Electric at 604-681-8338. One of our licensed electricians can help to diagnose the issues being experienced and bring everything back to working condition.

Having a hot tub or spa at home is a wonderful amenity. But before you have the ability to sit back and relax, there can be a lot of headaches. Proper preparation is required before you position the hot tub and plug it in. Here are a few things to keep in mind when planning your hot tub or spa installation.

You probably have an idea of where you would like to place your hot tub. If you are planning to build a place for it outdoors, ensure that you have:

Keep in mind the warranty of your hot tub. Some bases can void the warranty and the material of surrounding walkway, such as gravel, can track more debris into the hot tub.

For an indoor spa, ensure that the room you have chosen is suitable for the conditions. You will require a strong foundation as well as suitable ventilation for the steam and moisture.

Before starting a deck, support structure, or upgrades to a room in your home, check with your municipality that you are able to complete the improvements. You may require permits and there may be codes that your new structure must meet in addition to the manufactures’ warranty. Building illegally can cost you more in the long run.

This is where a certified electrician is important. Most hot tubs require approximately 240 volts. A hot tub does not plug directly into a standard outlet like other appliances; you will be required to add an additional circuit breaker into your main service panel. This can be a complex job and should be done correctly to keep your family and home safe. Improper electrical wiring can cause electrical surges and fires.