Aluminum LED profile housings allow you to create customized light fixtures with LED strip lights. Our Klus brand LED channels are available in many different styles, including recessed-, or flexible, O-shaped, and more. Available in 1- and 2-meter lengths, the channels can be easily cut for any application from under-cabinet lighting and bookshelf lighting to showcase lighting and transition strip lighting. They’re available with a variety of lens options, such as clear, frosted, and etched that complete the profiles. We’ve put together a step-by-step guide for using these channels to create your own light fixtures. Please note that your specific channel might vary from the one used in this tutorial.

Materials needed:

1. With a pair of clippers, carefully clip through the clear plastic heat shrink as shown in figures A-C. You will want to take your time and be careful not to cut the strip’s wires while removing it.

2. Lay the LED strip into the channel, and position it along the bottom so that the ends of the strip and the channel are lined up (fig. A). Now, remove the paper from the strip’s adhesive backing (fig. B), and adhere the strip to the LED channel—starting at the lined end and working your way to the other end of the strip. Be sure to leave roughly 1/4-inch free at the end of the channel so that you can install the end cap as shown in figure C.

3. If one of your end caps doesn’t come with a pre-drilled hole, you will need to drill your own to allow the wires of the LED strip light to come through. In this case, we used a Dremel tool, but other options are viable as well. Regardless of the tool you choose, it is helpful to mark the end cap where you would like the wires to come through. Start the hole small, and increase the size as necessary.

4. Place the end cap on the wired side of the strip by threading the wires through the end cap as shown in figure A. Insert the end cap into the end of the light bar, and push firmly until it is fully in place (fig. B).

5. On the open end of the bar, slightly peel up the end of the LED strip (fig. A); this is necessary to install the end cap. Now measure your channel lens, and trim off the excess with clippers (fig. B). Be careful when trimming to avoid cracking the plastic. Excess material can be lightly sanded off. Once the lens has been cut to the proper length, slide it into the channel, and install the end cap as shown in figures C and D.

6. That’s it! Your customized LED light fixture is complete and ready for installation, which we will cover in the next step.

7. Mounting this LED profile is as easy as applying double-sided tape to the back of it and sticking it to your intended surface. Be sure to cut the tape to fit the back of the LED profile and to leave the tape backing on the side not attached to the channel until you are ready to mount it.

For most LED profiles, mounting clips are available for a more permanent installation.

If you have questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

The frequency of accidents caused by the incorrect usage of electricity has increased as our dependency on electronic devices has increased over the last several years. Every year, accidental electrical fires cause millions of dollars in property damages. Because of this, you should always practice as much electrical safety as possible whenever you use your electrical appliances and devices. To make sure that your home is as safe as it can be from electrical accidents, you should also consider talking to an electrician in Glendale about performing an electrical safety assessment, updating service panels and ensuring that your home is properly grounded.

Can you use any size fuse or circuit breaker in your electrical panel?

Many older homes still utilize an outdated fuse box inside the service panel, instead of a safer and more modern breaker panel. If you still have a fuse box, then it is very likely that your electrical system is not prepared to take the amount of electricity that you use every day. This results in fuses blowing very frequently for many homeowners. Rather than replacing blown fuses with the appropriately sized replacements, some homeowners choose to oversize the fuse in order to reduce the frequency of blown fuses. This can be very dangerous, though not nearly as dangerous as replacing the fuse with something that cannot blow, such as a coin. Doing either of these should be avoided. Fuses are protective devices that are designed to stop electricity from flowing into a circuit whenever it reaches a level that is dangerous. Whenever you oversize or bypass a fuse, your circuit can overload. This can lead to overheating, fire and electrical shock.

One of the best ways to deal with an older fuse box is to have your electrical service upgraded by one of the technicians at The Electric Connection. We can send someone out to upgrade your service, and install the appropriately sized circuit breakers in your new electrical service panel. If you are experiencing any issues with your electrical panel, please don’t hesitate to give us a call today.

Click here to visit our website.

The traditional lighting style–while tasteful and low-key–provides just the right touch when you want to draw the eye to a design focal point without overpowering it. Few lighting styles work as unobtrusively as transitional chandeliers while managing to showcase an advanced stylishness for discerning design aficionados. You can choose from Capitol’s vast selection of lighting features that include:

• Multiple glass shade shapes

• Brass, crystal and metal finishes to complement existing or planned furnishings

• Finishes that include bronze tones, gold accents, brushed nickel, polished nickel, clear and crystal

• Fixture styles that include pendant lights, chandeliers, mini chandeliers, island lights, flush-mounted lights, recessed lighting and track and rail lighting

• Bulb types that include incandescent, fluorescent, halogen and LED technologies

• Energy Star lighting efficiency

• Title 24 compliant

• Dimmable fixtures

NAHB), 9 out of 10 people who are looking for a new home are more likely to choose an energy-efficient home. And, they are often willing to pay a little more for it.

cheat sheet to help you choose the right one.

Exterior lighting made the top 5 on the list of most wanted new home features. Make that lighting energy-efficient, and you’ve got a winning combination for attracting buyers. Contrary to popular belief, a low voltage outdoor lighting system doesn’t necessarily save you in energy costs. However, when you add LEDs into the mix, it’s a whole different story. Energy star rated LEDs use about 75% less energy than incandescent lights and last 25 times longer. Installing an walk into an empty room that still has every light on? Lighting controls like occupancy sensors save energy by detecting body heat and dim your lights, it reduces energy use and extends the life of your bulb. According to Lutron’s bathroom, bedroom or Earth Day Energy Center.