That new electric car will surely save you money on gas and make you feel good about doing something good for the environment, but there are some things you must consider. Before you start planning that trip to Paris with all the money you save on gas, you need to figure out how you will keep the car charged. Without a charge, you will need to rely on gas, thus defeating the purpose of your electric car. This is why you need an electrician. Burbank electric car owners can call The Electric Connection for help.

When you purchased your car of if you are in the research phase and trying to figure out what car to buy, you probably heard about the charging stations. There are two main types. The slower charging stations are much less expensive while the others are faster and more expensive. Obviously, the less expensive station has a major benefit and it can be plugged in virtually anywhere. This makes it convenient to charge the car. However, the downside is the time it takes to give the car a full charge.

On the other hand, you have the initial investment of the faster charging system. But, in this case, the car will charge in about 8 hours versus the 16 to 24 hours it takes for the slower system. Because it is a much more powerful electric car charging station, you will need an electrician. Burbank residents will need a dedicated 240-volt outlet to plug the station into. An electrician will need to check the electric panel to make sure there is enough space to support the additional electrical needs. If you would like to learn more about the different electric car charging stations, give The Electric Connection a call. If you have already made the decision to purchase a fast charging station, we can install it for you.

1-by-4-foot,  LED light panels use Even-Glow® technology and diffused optical lenses to deliver smooth, flawless illumination without visible bulbs or hot spots. They can be recessed mounted or surface mounted to an existing ceiling junction box. The LED fixtures emit up to 4,600 lumens of natural white illumination for home lighting, kitchen lighting, living room lighting, office lighting, basement lighting, sign backlighting, hospital lighting, and more.

LEDs in the panel lights are designed to last five times longer than fluorescent tube light bulbs without the notorious hum or flicker they produce. Each LED panel light has a slim, white aluminum alloy frame and an internal 0-10-volt dimmable constant-current driver. Dimming can be achieved with a 0-10-volt switch or by using the light’s power-cycle feature to activate set brightness levels. The energy-efficient panel lights operate within a 100-277V AC range.

In our new 5th Wheel RV, we received some ceiling mounted 12VDC florescent fixtures. They were equipped with 2 each 18”, 15W tubes and electronic ballasts. The fixtures are a “Low Voltage RV Luminaire” from “Direct Sourcing Alliance” identified as “Type RVL 18RNB-W”, “2 x 15W”, “Input Rating: 12V DC, 30W”. Their performance has been dismal with operation limited to, initially 30-45 minutes before shutting down due to overheating of the ballast. The “on” time got progressively shorter over the next few weeks. The overheating was certainly not due to ambient temperatures which have been in the low 70s or cooler. On disassembly for conversion to LED operation it was discovered the ballasts have discolored due to high heat (see closest end of ballast in Picture 2).

During review of options for LED conversion I was looking for a natural light color temperature with equivalent lumen output to the two 15W florescent tubes. I settled on the SuperBrightLEDs part number RLBN-NW30*3SMD which is a 19.5 inch rigid strip with 30 each 3SMD modules. The advertised light output was 603 lumin at a color temperature of 5600K. The two 18”, 15W tubes were stated to produce 825 lumins each so I was a little concerned about light loss especially since I was going to have to cut 6 LED modules off each of the two strips to fit inside the existing fixture. I bought a 3rd strip but in the end did not use it as the light was ample.

I first started by removing the “guts” of the florescent leaving some length of the switched power wires for future use. See pictures 1, 2, and 3.

After cleaning the interior of the fixture with alcohol for acrylic tape adhesion I fitted the rigid LED strips and cut 6 LED modules from the length, then mounted the strips using 3M double sided acrylic tape. Finally, completed power connections to existing fixture switch circuit. See pictures 4 through 10.

;

When installed and operating properly, security lighting like motion lights can add a great measure of safety and security to your Bethesda home. But these systems are not flawless, and they come with their fair share of frustrations and difficulties. Having issues with a motion light that stays on at all hours? The certified electricians at Kolb Electric have an answer!

Looking for a reliable electrician to perform an outdoor lighting installation for your home in Maryland? Contact Kolb today!

The good news is there are only really a few potential causes for this, and many of your solutions are a fairly quick fix. There is an issue or two that might require a professional’s assistance, but we’ll get to that later. For now, your problems are most likely caused by:

If your outdoor lighting installation is still acting up, we’re sorry to say that there’s a good chance you’re dealing with damage that requires the help of a certified Bethesda electrician. Most likely what you have is a damaged motion light fixture. The damage can come from a few sources, one or two of which might sound familiar:

If you’re having issues with your security lighting in Bethesda, you can always count on the experts at Kolb to get you the service and dependable solutions you need! Contact our team today to find out how a certified Kolb electrician can help you restore your security lighting, or if you want to learn more about our outdoor lighting installation services!