When a light switch or electrical outlet doesn’t function correctly, a professional electrician can trace this back to a variety of causes. First, it’s possible this non-functioning device was never connected to the wiring in your building. Secondly, the circuit affected by a switch or outlet may not be completed because of another component. For example, a switch may control an outlet which is unoccupied by a lamp or any other electrical device. Also, an outlet may be connected to a switch which is in the off position. A third cause might be related to a defective breaker, or a breaker which was tripped or turned off, but never switched back on. However, a fourth possibility may relate to a much larger problem.

Sometimes, a switch or outlet fails when it is damaged by arcing. If the arcing was caused by a connection to aluminum wiring, great potential hazards exist. If your home or building was constructed or renovated before 1972, or during the late sixties, it may contain aluminum wiring. Aluminum wiring was used legally during those years, but outlawed for installation in new homes, commercial buildings, remodels and renovations after it was identified with conditions which could lead to electrical fires.

Although aluminum wiring itself is generally no more hazardous than copper, its splices and connections with other metals present a real hazard because they can become corroded and begin arcing. Because arcing in these connections can lead to a fire within surrounding materials, aluminum wire was discontinued. However, many homes still contain aluminum wiring, and research conducted by the Consumer Product Safety Commission (CPSC) reveals that buildings with aluminum wiring pose a fire risk which is 55 times greater than the risks with similar structures wired with copper. So, if you discover an electrical outlet or switch which doesn’t appear to be functioning correctly, it’s possible this outlet or switch was damaged by a connection with aluminum wiring.

If you have safety questions about this type of problem, or any electrical concerns regarding your residence or commercial building, please contact Bryant Electric Service at 512-402-8587. Our licensed electricians are trained and equipped to perform professional safety inspections, and they can repair any type of electrical problem.

Most people have experienced a circuit breaker trip at some time or the other; and the first couple of times it happens, it can be quite alarming. However, this is a very important safety component in any electrical circuit. A circuit breaker is essentially an automatic device used to stop the flow of current within a circuit, as a safety measure. It is specifically designed to protect your property, equipment in your home/commercial space and you from overloading the electrical circuit.

The sole reason a circuit breaker trips is to prevent the overheating and overloading of an electrical circuit, beyond the capacity of that circuit. If there is no breaker in place, the electrical units in that circuit can get damaged and potentially lead to a fire.

In case a circuit breaker trips, the very first thing to do is to locate it in your panel box. The switch you are looking for is the one that isn’t completely in an On/Off position. Once you turn the switch into the ‘on’ position, the power will be restored. In case the power doesn’t come on, simply switch it off and then on again.

If the circuit breaker trips even after you have reset it, don’t just try resetting it again. It’s doing what it’s designed to do and telling you that there is something wrong that has to be investigated. There are three different things that can cause a circuit breaker to trip:

This is the commonest cause of a circuit breaker trip. It occurs when the electrical energy that’s flowing through the circuit is much more than what it can handle. The simplest way to solve this problem is to redistribute the power to some other circuits. Very simply put, in case too many heavy appliances are connected to a single circuit, move a couple of them to one that isn’t as loaded.

It’s important that you check whether the circuits aren’t loose. First, switch off the power and look for any loose wires; you can do this by closely inspecting the hot wires and outlets that lead from the service panel to the circuit breaker, and then tighten the connection that’s loose.

If after checking the circuit overload, you find there aren’t any issues in that areas, the problem could be a short circuit. This is caused when any live wire touches another neutral/live wire. At times a short circuit may be caused by a broken wire within the breaker. It’s far more difficult to identify this as it could be just about any part of the wiring system which is connected to that circuit. At times, the culprit could be an appliance that’s plugged into an outlet.

This issue is quite a dangerous and severe one and it’s important that it be diagnosed quickly. It can be quite tedious to look for a short circuit and the outlets, plugs and wiring that are connected to that circuit, but these checks are important. Look for cracks or signs of burning in the insulation and call an electrician without delay.

If it’s neither a short circuit nor a circuit overload that’s caused the circuit breaker to trip, it could be a ground fault issue. This happens when any hot wire touches the metal outlet box or the ground wire.

If a circuit breaker trips in your home or commercial property, keep in mind that it’s a very serious issue and not something that should be ignored. For the best electrical solutions, call Allround Electrical at 1300 169 263. You can also drop us a line via email or contact us through this online form.

Thanks for reading,1300 169 263

An inexpensive way to help ventilate your bathroom is with the installation of a bathroom fan. If you already have one, is it adequate? Homeowners have probably realized an improperly operating or nonexistent bath fan results in excess moisture in the bathroom. This leads to numerous problems including mold growth. An electrician in Los Angeles can take care of the installation or replacement of your bath fan.

Why You Need a Bath Fan

Bath fans are essential tools needed to keep the humidity level down in the bathroom during hot showers. Without a way to pull the hot air out, condensation builds up on every surface in the bathroom, including the toilet paper! This is clearly not something you want to experience. Mold growth can become problematic and leave the bathroom with an unpleasant mildew smell.

DIY or Electrician?

If you have an existing bath fan that needs replaced, it is typically a fairly simple swap. You will need to handle some electric wires as you disconnect the old and wire in the new one. If you are familiar with electrical work this is a pretty easy task. If you have never dealt with wiring, it is advisable you contact your Los Angeles electrician to handle the job for you. You will need to consider your personal safety before embarking on this task.

If there is not a current fan, you have a little more work to do. You will need to properly vent the pipe, cut a hole in the ceiling and bring in an electrical connection to hook the fan up to. This is definitely a job you will want to leave to the professionals. A switch to turn the fan off and on will also need to be installed.

If you are ready to keep your bathroom dry and mildew free, give The Electric Connection a call.

The electricity running through your home from the main power grid is fast and hot. In the U.S., supply lines carry electricity at 115 to 240 volts. When you plug something in, you’re dipping into this current to power your appliances and lights, making the potential for electrical outlet sparking very real.

Sparks are no laughing matter. If they’re large and hot enough, they can even start a house fire. So when you notice electrical outlet sparking in your home, it’s important to take a closer look. While some sparks may be part of normal operation, other times they can be a sign of a severe issue. It all depends on the cause of the sparking.