Under-Cabinet LED Lighting Kit is available for purchase that contains a plug-and-play LED light strip, push-button dimmer, remote, 12V power supply, and connection accessories. If you want to build a custom kit, follow the steps below the diagram to ensure that you get everything you need.

3. Select a dimmer or controller

For single-color LED strip light setup

Select the power supply large enough to operate the amount of LED strip light you need to use. If you want to control the brightness of your light strips, you will need a Single-color dimmer shown installed with a non-dimmable power supply

For color-changing LED strip light setup

Follow the instructions above for the single-color light strip setup. However, instead of a dimmer, use a RGB color-changing light strip installation

4. Use an LED amplifier for long runs of strip

Depending on the strip chosen and its maximum run (the number of strips that can be installed consecutively before needing amplifiers), you will need to install an light strip interconnect cables. It is best to purchase a length of strip that is more than your application requires. For example, if your project requires 8 1/2 feet of strip, we recommend purchasing 9 feet of strip to ensure that you have everything covered.

A summer in Florida brings about a ton of exciting activities. From the pool to the playground, there’s a lot of adventure to be had! But don’t break out the barbecue just yet! The certified electricians at Hoffman Electrical would like to take a moment to identify some common electrical hazards that can come as a result of all of this summer fun.

Our experts have been bringing our patrons the best in electrical services for years. And in that time nothing has ever been as important to us as your safety! To avoid risks of shock and fire, read along for some safety tips you should put into practice.

Don’t worry, we’re not going to spoil the fun. These tips are quick, easy, and are mostly about taking precautions:

If it’s time to bolster the electrical defenses of your home, look to the certified electricians at Hoffman Electrical! We can ensure your home is safe and shock free this summer, leaving you to have fun in safety! Hoffman Electrical is a family owned and operated business serving the Tampa and Brandon, Florida communities since 1989. Our friendly and knowledgeable staff of electricians install, repair, and perform regular maintenance check-ups in Hillsborough and Pinellas counties.

With over 1 million homes in the Dallas area over 20 years old, older home electrical safety is a major concern that should be assessed by a licensed Dallas electrician. Many homes in the 70’s and 80’s were built with electrical wiring and breaker panels that have been known to be a fire and electrical shock hazards. If you live in one of these older homes, and it has not been updated, it is very important that you have a licensed Dallas electrician come out and take a look at the electrical system in your home, to ensure your family’s safety.

RGB LED strip lights are a great way to add a pop of color to your above-ground pool. These low-voltage LED lights can be applied to the inside rim of your pool or around your pool deck. With RGB LED strip lights, you can choose from a ton of dynamic color-changing and single-color modes with adjustable brightness and speed control. They’re great for parties or late-night swims and can be easily installed. We’ve included installation instructions for our waterproof LED strip lights. Some cities require above-ground pool lighting to meet National Electrical Code (NEC) Article 680 standards, which would limit possible pool lighting installation locations. Before you purchase LED pool lights, check your city’s code requirements. We also recommend that you have a certified electrician install your lights.

1) Before ordering your LED strip lights, measure the diameter of your pool and multiply by 3.14 to find its circumference; this number indicates the total length of strip that you will need. The 21-foot pool used for these installation instructions has a circumference of 65.94 feet and requires 4 runs of 16-foot LED strips.

You will also need to measure the distance between where your power supply will be and both sides of your pool where the amplifiers will be installed (see the setup and wiring illustration below). These distances will tell you how much 18-gauge wire you’ll need for connecting the amplifiers to power. Make sure to account for the distance of any dips or turns that the wires may take along their paths.

Lastly, measure the approximate distance that will be between your controller and where your strip lights begin. This distance will tell you how much 22-gauge wire you’ll need for connecting the controller to your strips. You will also need two small sections of this wire for connecting your first and second strip lights to the amplifiers.

2) Before you’re ready to install your LED strip lights, be sure to drain your pool. Begin by creating or locating a dry area away from your pool for the power supply. The power supply should be contained in a weatherproof box. Power supplies should be installed between a ground fault circuit interrupter (GFCI) protected circuit and the pool’s junction box. It’s crucial to use a GFCI protected circuit as it shuts off if current flows where it’s not supposed to.

Wire the included plug to the power supply, but do not connect to power until the installation is complete.

3) Connect your RGB LED controller to the power supply. Cut the barrel off of the controller wiring. Strip back the remaining wires, and connect its wires to the power supply.

4) Cut the LC2 connector off of the remaining end of the controller, and strip back the wires. Run 22-gauge four-conductor wire to connect the controller to your low-voltage pool lights; use dolphin connectors to join like-colored wires. Connect your first two LED strip lights to the controller by joining each set of like-colored wire with a dolphin connector. You should be connecting four wires of each color (red, blue, green, and black) together. For added protection, cover all wire connections in this installation with electrical tape.

5) You will apply strip 1 clockwise around your pool rim and strip 2 counterclockwise. If you have a flat surface, use mounting clips to secure the strips in place as you go. If you want to mount the strips under your pool rim, drill small holes in the trusses approximately every 2 feet. Use cable ties to anchor the strip to the truss. You can also use speed nuts or cotter pins for strip anchoring to avoid drilling holes.

Solder a small section of 22-gauge four-conductor wire onto the strip’s end terminals. To reseal the LED pool light strip, slide wires through the holes of a 10-mm end cap, fill the cap with silicone, and slide it into place on the end of the strip. Be sure to cover all of the exposed conductive traces to ensure water resistance. Allow a minimum of two to three hours for the sealant to cure.

7) Once the new end wires are attached to the strip, you will mount the amplifier. Use the double-sided 3M foam pad to mount the amplifier in the middle of strip 1 and strip 3. For best results and added security, apply 3M adhesion promoter to the amplifier and its installation location on the pool wall.

8) Using a dolphin connector, join each like-colored wire on strip 1 to the same color on one end of the amplifier. Do the same when connecting strip 3 to the other side of the amplifier. You should be connecting three wires in each color (red, blue, and green) together on each side of the amplifier. The black strip wire will be joined with white amplifier wire. Note that the separate group of just black and red wires are meant to be connected to the power supply. Follow the same instructions for connecting strips 2 and 4 to the amplifier on the other side of the pool.

9) Use 18-gauge wire and dolphin connectors to connect the amplifiers to your power supply.

10) Plug the power supply’s attached cord into an outlet, and enjoy your LED pool lighting system! Refill your pool with water, but make sure to leave space between the water line and the lights.

For more LED pool lighting options, see our entire selection of waterproof color-changing LED strip lights.

For technical questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.