Most new buildings are now using a variety of electrical and electronic equipment. As such, the contractors have to design a wiring schematic that will deliver power to a wide and diverse range of devices that include traditional and modern electrical loads.  The wiring must also provide a means of supplying power to the monitoring and control devices such as wireless sensors, thermostats, automatic light controls, thermostats, the IoT, and other web-based technologies.

The electrical requirements will vary from one building to another and may include a combination of the following components:

The type and use of a building structure influences the type of wiring to use. And the building owner and electrical contractor should consider current and future power requirements when determining the size of conductors, raceways, protective gear and other necessities.

GFCIs or ground fault circuit interrupters are safety devices that have been extremely effective in reducing the total number of home electrocutions by almost 50%, in Australia. Most new homes and businesses now have these devices installed in locations where water is present in and around the premises. It’s important that electrical installations in outdoor locations be protected from wind and rain; that’s the one way to prevent shock hazards.

Before we understand what a GFCI is, let’s understand what a ground fault is. It is the unintentional flow of electrical current between the source and any grounded surface. If the electrical installation isn’t properly protected, an individual that comes into contact with an energised part can suffer an electrical shock.

For instance, if the person is holding any deteriorated electrical cord attached to the hair dryer, and it happens to touch a plumbing fixture they are using, they can get electrocuted and will suffer a painful shock.

This small receptacle has “test” & “retest” buttons on it. It may sometimes be built into circuit breakers that are installed in the main electrical panels. When electricians are conducting an electrical audit, they also test whether the GFCIs are functioning properly. They might also recommend that you get GFCIs installed in the vicinity of plumbing fixtures.

These are extremely useful electrical safety devices which trip the electrical circuits in case they detect any leakage current or ground fault. An individual that’s become the pathway for a leaked current can get a severe shock or will get electrocuted. It is important to get GFCIs installed in any outdoor or indoor areas where you feel that water might come in contact with the electrical installations or fixtures you have on your property.

Ideally, the areas where GFCIs should be installed include:

It is important that these devices be checked with regularity. If you have opted for an electrical maintenance contract, the electricians will ensure that the GFCIs are checked along with all the other installations; this will help confirm they are working as they should and that they provide the necessary safety to those living or working on your premises. You can also test the GFCIs on your property, by following these basic steps:

If you aren’t too sure about whether you have GFCIs installed at the right points on your property, call in your local electrician. They will inspect all the fixtures and inform you if GFCIs have to be installed in any specific rooms or outdoor spaces. Aside from this, they will also audit the rest of the installations and tell you if any upgrades are required.

By: Jason Lee

Halloween is over which means the holidays are officially here. That means the relatives are on their way and you’ll be using your large appliances more often causing your electric bill to look scary long after Halloween has ended. Don’t let the increase in relative visits and vampire electric devices drive up the electric bill.

To keep the electric bill down, remember to only use the dishwasher when it is full. Running the dishwasher when it is only half full will amount to a lot more energy consumption.

Items like washers and dryers are guilty of consuming more energy during the holidays too. Washing clothes in cold water and setting the dryer on low heat will help in reducing the electric bill.

Knowing when to say goodbye to your old system is another way to save on energy. Older appliances run up the electric bill. If you have an appliance that is over 10 years old, consider replacing it with a newer, energy efficient model.      

It is also a good idea to have all large household appliances connected to their own dedicated circuit. To many of these large appliances operating at the same time on the same circuit can cause a blown fuse or a tripped breaker. A dedicated circuit for each large electrical household appliance will keep this from happening.

Lastly, don’t let your everyday electrical devices like laptops, cell phones or tablets get greedy and hog the power outlets. Only charge these items when they need it.                                                     

You’ll have enough to worry about as the holidays set in. Take the electric bill off the list by doing these simple energy savings tips from Mr. Electric.

With the long days of summer fast approaching, many homeowners are contemplating a home solar panel installation. If you’re one of them, start making plans now!

Homeowners stand to get the most energy out of solar panels during the summer months, since greater sunlight will hit them. That translates to more savings and a greater immediate return on your investment.

But people tend to pursue these solar installations when there is more sun, increasing the demand and the workload for solar installers. We’re not complaining, but it does mean that sometimes orders aren’t completed with the lightning speed we prefer. The sooner you set up an installation, the sooner we can have it complete. There are sometimes more steps than just putting panels and a system on your home. Improvements to the roof or the yard to accommodate a system of your specifications can be necessary, which lengthens the process.

The advantages of getting a jump on the competition are significant. As soon as your system is active, you’ll see immediate reduction of your power bill, leading to greater and greater savings over the years, as municipal power costs rise.

Additionally, nobody knows how long the incredible financial incentives for solar panels will last. Longstanding federal tax incentives are currently bolstered by powerful rebates and incentives offered by local authorities but they won’t last forever. If you want to take advantage of them and get a solar installation switched on before summer arrives, give us a call to schedule a consultation. We can start the planning process right away and give you quotes the same day so you know exactly what a solar panel installation will look like at your home. We’re gearing up for a busy summer and we hope to see you out there!