Let’s face it—halogen and incandescent headlight bulbs are a thing of the past. fanless, driverless LED headlight bulbs were used in this installation.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points. Repeat these tape lines for your other headlight.

6. Remove your headlight assembly if necessary, remove the current bulbs, and install your new LED bulbs. Check your owner’s manual for specific instructions on how to replace your headlight bulbs.

7. Depending on your vehicle, you may have to adjust your headlight beam before or after the assembly has been reinstalled. Your owner’s manual will explain how to adjust the beams. Align each headlight so that the top edge of the beam is at the same height as your horizontal line(s). If your headlights can be adjusted horizontally or produce two light cutoff points, use the vertical tape lines to align them properly.

3. Shake the vehicle to ensure that your suspension system is settled. For more precise adjustments, inflate all tires to their designated psi capacity and have someone sit in the driver’s seat. Also, make sure that your vehicle’s gas tank is at least half full.

4. Measure from the ground to the center of your headlight assembly where the bulb is located. This step must be done for all vehicles. If your vehicle allows for horizontal headlight adjustments in addition to vertical adjustments, it’s important that you also measure the distance between the centers of both headlight bulbs. The vehicle featured in this video allows for vertical headlight adjustments only; therefore, center lines aren’t necessary but are shown for demonstration purposes.

5. Turn on your low-beam headlights. Using painter’s tape, mark your headlight measurements on a flat wall. Measure from the ground up, and apply a horizontal line of tape to the wall; this line represents the top of your headlight beam. You can either apply one long, continuous line or small sections where the brightest areas of the headlight beams are shown.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points.

If there’s one thing kids seem to love, it’s playing with everything around the house other than their toys—the more dangerous the better! Electrical outlets in particular are an endless source of fascination for young children, and according to the Electrical Safety Foundation International, hospitals across the country treat nearly seven children for electric shock and burn injuries related to tampering with wall outlets each day. But buying childproofing devices for your electrical outlets can be a challenge, and if you don’t choose carefully they may not fit in your outlets or may be too easy for your child to pull out. So how do you choose?

There are two types of outlets commonly seen in homes—standard and decorator outlets. You can tell them apart by looking at the number of screws they have:

Different types of outlets have different requirements for childproofing materials, so figuring out which type you have is very important. Note that standard outlets will be able to use most childproofing methods—decorator outlets are a little more complicated, but the packages on the items you buy should list whether they are compatible. Remember that most items approved for decorator outlets will not work in standard outlets, and vice-versa, so choose carefully!

Outlet covers, which usually plug right into the outlet, are a good choice for outlets that have “fixed” items that are plugged in all the time, such as lamps or televisions, as well as areas that use large adapters like at the computer. Outlet covers are effective at keeping both infants and toddlers out of the outlets, which means they’ll last for a number of years. Outlet covers for both standard and decorator outlets can be purchased.

Unlike outlet covers, safety outlet plates replace your existing outlet plates and have a small sliding door that covers the receptacle when not in use. These work best for outlets that you have to repeatedly plug things into and unplug things from, such as a vacuum cleaner. They are also difficult for children to figure out and should be effective for many years.

Ideal for outlets that are kept out of site and rarely used, outlet plugs are usually easier for kids to figure out but are still good at preventing access to the inside of the outlet. The good news is that they can be used interchangeably in standard and decorator outlets.

Keeping your children safe is your number one priority, and childproofing your electrical outlets is a great way to do that. Damaged or malfunctioning outlets can also be a major safety hazard in your home, so if you need outlet repair in Maryland, Virginia, or Washington, DC, call Kolb Electric today!

Spring has sprung. This means more days where it gets a little warm and you may need some air conditioning—but not so warm that you can count on turning off the heater for the year though. While your utility bills may be a bit lower in springtime than in other times of the year, it is still a concern. One of the best ways you can keep those utility bills even lower is by sealing your home against temperature loss. This does not cost much and is something you can do yourself—though a Glendale electrician may be able to provide advice if you find yourself with questions.

Sealing your home is one of the most effective means of keeping down energy consumption—this not only lowers your utility bills, it can reduce your reliance on fossil fuels too. Consider these tips as a great place to get started:

Are you thinking that it might be a good time to install solar panels for your home? More correctly, there has never been a better time to invest in solar panels. Why is it such a good time to install solar panels?

For starters, there are incredible federal tax rebates currently in place that allow you to detect a portion of the expense of installing the panels from your taxes. About a third of that cost, no matter the cost, can be subtracted from your taxes.

The California Solar Initiative was put in place a few years back to encourage residents to take advantage of one of our most abundant resources: sunshine. Now, you may be eligible for a variety of monetary incentives to install a home solar array. The policies are extremely varied across the state, and many of them have expired. Some areas still have potential for Solar Incentives, so acting now could save you additional money.

There is already a favorable picture of the solar installation scene right now, but it gets even better when you consider solar leasing. Solar leasing isn’t the right choice for everybody, but it has tremendous allure, too. Basically, solar leasing is a partnership between you and a solar installation contractor. They install the system and you pay back the cost of the materials over time. Even as they pay down their solar lease, many residents enjoy savings on their power bills, too. You might even be eligible for free installation, making the proposition an investment of zero dollars for a lifetime of savings.

If you’re interested in the potential of solar panels and solar leasing, call us to discuss your options. We can get you started with a quote over the phone today and soon have a solar array up at your house. It’s never too late to start saving, so start today!